EUROSYS 15PM - Active speaker PEAVEY - Free user manual and instructions

Product Type	Active amplified speaker (stage monitor)
Brand	PEAVEY
Model	EUROSYS 15PM
Format	Stage monitor / floor wedge
Speaker	15 inches (estimated)
Amplification	Built-in, 105 W continuous (8 Ω) / 150 W (4 Ω)
Inputs	2 parallel connectors (XLR or 6.35 mm jack)
Extension output	Connector for passive speaker (min. impedance 8 Ω)
Equalizer	4-band graphic: 100 Hz, 1 kHz, 5 kHz, 10 kHz, ±12 dB
Volume	Rotary volume control
Power supply	230 V AC, 50/60 Hz
Fuse	1.6 A, slow-blow
Power consumption	325 W max
Input sensitivity	0.7 V for 105 W at 8 Ω
Indicator	Power-on LED
Dimensions (H x W x D) (estimated)	70 x 43 x 35 cm
Weight (estimated)	20 kg
Maintenance	Clean with a soft dry cloth
Safety	Unplug before maintenance, do not expose to moisture
Included accessories	IEC power cord

Frequently Asked Questions - EUROSYS 15PM PEAVEY

How to connect the EuroSys 15PM to a mixing console?

Use the line inputs (XLR or 6.35 mm jack) by connecting the monitor output of your mixing console. The Volume knob controls the level.

What is the power of the built-in amplifier?

The amplifier delivers 105 watts continuous at 8 ohms and 150 watts at 4 ohms.

How to use the 4-band equalizer?

The equalizer has 4 faders (100 Hz, 1 kHz, 5 kHz, 10 kHz) allowing a correction of ±12 dB. They are used to correct feedback problems.

Can I daisy-chain multiple EuroSys 15PM?

Yes, the two parallel inputs allow daisy-chaining multiple speakers. You can also connect a passive speaker (8 ohms minimum) to the extension connector.

What type of fuse to use?

Use a slow-blow fuse of 1.6 amperes. Check the fuse holder near the IEC power inlet.

What are the dimensions and weight of the speaker?

Approximate dimensions are 70 x 43 x 35 cm (H x W x D) and weight about 20 kg.

How to maintain the EuroSys 15PM?

Clean the cabinet with a soft dry cloth. Always disconnect the device before any maintenance. Avoid moisture and impacts.

Can the speaker be used as a floor monitor?

Yes, the EuroSys 15PM is designed as a stage monitor and can be placed on the floor oriented towards the musician.

What is the input sensitivity?

The sensitivity is 0.7 V to obtain 105 watts at 8 ohms. It is compatible with line outputs of mixing consoles.

Can I connect an instrument directly?

It is not recommended to connect a guitar or microphone directly without a preamp. Use a mixing console or a suitable adapter to adjust the level.

USER MANUAL EUROSYS 15PM PEAVEY

EuroSys 15PM Powered Monitor Enclosure

OPERATING INSTRUCTIONS

EuroSys 15PM

Powered Monitor Enclosure

OPERATING INSTRUCTIONS

WARNING! TO PREVENT SHOCK OR FIRE HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE FROM CASE. NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL. REPLACE FUSE ONLY WITH ONE OF THE SAME TYPE AND SPECIFICATION.

Thank you for choosing Peavey's Eurosys 15PM powered monitor enclosure as part of your sound reinforcement system. We take great pride in the design and manufacture of our units and you can expect top performance and reliability. Your Eurosys 15PM has been rigorously tested before packing and despatch to your dealer. It has been designed to run from a nominal 230 Volt AC mains supply.

1. AMPLIFIER INPUTS

Use to connect line level signals from the monitor send of the mixer. Two sockets are provided to allow connection to further Eurosys 15PM powered monitors. (Daisy chaining).

2. VOLUME

This slider controls the level or volume of the enclosure.

3. 4 BAND GRAPHIC EQUALISER

Four sliders allowing up to +/- 12dB of adjustment at the centre frequencies of: - 100Hz, 1KHz, 5KHz and 10KHz. Use to assist with any feedback problems.

4. ~ PILOT LIGHT

Illuminates when AC mains power is being supplied to the amplifier.

5. EXTENSION SPEAKER SOCKET

Allows connection of a further unpowered monitor with an impedance of 8 ohms. The power amplifier will develop full power into 4 ohms. (150 Watts).

6. POWER SWITCH

Use to turn the Eurosys 15PM ON or OFF

7. MAINS CONNECTOR & FUSE HOLDER

An IEC 320 combined mains connector and fuse holder is fitted. A separate 3-wire mains cord fitted with a moulded plug is supplied.

8. 13 AMP PLUG REPLACEMENT

As the colours of the wires in the mains lead or cord of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

• the wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol, or coloured green or green yellow.
• the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
• the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

WARNING - THIS APPARATUS MUST BE EARTHED

SPECIFICATIONS

POWER OUTPUT (TYPICALLY)

105 Watts into 8 ohms

150 Watts into 4 ohms

INPUT SENSITIVITY

0.7 volt for 105 Watts into 8 ohms

FUSE RATING

1.6 ampere anti surge.

POWER REQUIREMENTS

325 Watts at 150 Watts output

MAINS VOLTAGE REQUIREMENTS

230 Volts AC (only) 50 / 60Hz

IN CASE OF DIFFICULTY CONSULT YOUR AUTHORISED PEAVEY DEALER

Due to our efforts for constant improvement, features and specifications are subject to change without notice.

Great Folds Road, Oakley Hay , Corby, Northamptonshire, NN18 9ET, England

Tel: [phone] Fax: [phone]