LSDP1-020-060-22 - Water pump Vevor - Free user manual and instructions
Find the device manual for free LSDP1-020-060-22 Vevor in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Water Pump |
| Brand | Vevor |
| Model | LSDP1-020-060-22 |
| Maximum Flow Rate | 20 L/min |
| Maximum Head | 60 m |
| Rated Power | 600 W |
| Supply Voltage | 220-240 V ~ 50 Hz |
| Inlet / Outlet | G1 inch (25 mm) |
| Maximum Liquid Temperature | 35 °C |
| Protection Rating | IPX4 |
| Pump Material | Cast iron body, stainless steel impeller |
| Maximum Suction Lift | 8 m |
| Maximum Operating Pressure | 6 bar |
| Dimensions (W x H x D) | 40 x 25 x 20 cm |
| Net Weight | 12 kg |
| Maintenance | Regularly clean strainer and check shaft seal |
| Safety Features | Thermal overload protection, dry-run protection |
| Spare Parts | Replacement seals and impellers available |
| Warranty | 1 year |
Frequently Asked Questions - LSDP1-020-060-22 Vevor
How do I properly install the Vevor LSDP1-020-060-22 water pump?
Place the pump on a flat, stable surface. Connect the inlet and outlet pipes securely, ensuring the pipe diameter matches the G1 (1 inch) connections. Use thread sealant on the joints to prevent leaks.
What is the maximum suction head for this pump?
The maximum suction lift is 8 meters. Install the pump as close as possible to the water source to reduce suction resistance and ensure a shorter vertical lift.
Can I let the pump run without water?
No. Running the pump dry can cause seal damage and overheating. Always fill the pump casing with water before starting, and never operate it when the water supply is interrupted.
How do I prime the pump?
Remove the priming plug, fill the pump casing with clean water until it overflows, then replace the plug and start the motor. This ensures the impeller is fully submerged for proper suction.
How often should I clean the strainer?
Inspect the strainer every 100 hours of operation and clean it if any debris is visible. A clogged strainer reduces flow and can cause cavitation.
What type of fluid can this pump handle?
The pump is designed for clean, non-corrosive water with a maximum temperature of 35°C. Do not use it with flammable, abrasive, or chemical fluids.
Is the pump self-priming?
No, this pump is not self-priming. It must be manually primed before the first use of each session. Ensure the inlet pipe is always filled with water.
What is the maximum operating pressure?
The maximum operating pressure is 6 bar. Use pressure-rated hoses and fittings, and monitor the pressure gauge to avoid exceeding this limit.
How do I store the pump during winter?
Drain all water from the pump and pipes to prevent freezing damage. Store the pump in a dry, frost-free location and disconnect it from the power supply.
Where can I find spare parts for this pump?
Spare parts such as impellers, shaft seals, and O-rings are available from Vevor's official website or through authorized dealers. Always use genuine parts for compatibility.
User questions about LSDP1-020-060-22 Vevor
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Water pump in PDF format for free! Find your manual LSDP1-020-060-22 - Vevor and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. LSDP1-020-060-22 by Vevor.
USER MANUAL LSDP1-020-060-22 Vevor
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Vevor
Model : LSDP1-020-060-22
Category : Water pump