CUT-50 - Welding machine Vevor - Free user manual and instructions
Find the device manual for free CUT-50 Vevor in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product type | Welding machine / plasma cutter |
| Brand | Vevor |
| Model | CUT-50 |
| Supply voltage | 230 V ± 10% / 50 Hz |
| Cutting current | 30 - 50 A (adjustable) |
| Duty cycle | 60% at 40 A |
| Maximum cutting thickness | 12 mm (steel), 8 mm (stainless steel) |
| Compressed air supply | Uses an external compressor (pressure 3-5 bar) |
| Cooling type | Forced air cooling |
| Digital display | Yes, for cutting current |
| Cable length | Approximately 3 m (torch cable and ground clamp) |
| Weight | Approximately 5.8 kg |
| Dimensions (L × W × H) | Approximately 30 × 14 × 18 cm |
| Main functions | Plasma cutting, current adjustment, thermal protection, LED indication |
| Maintenance and cleaning | Regularly clean dust from the ventilation grilles and check the condition of the torch and consumables |
| Safety | Protection against overheating, overcurrent; wear personal protective equipment |
| Spare parts and repairability | Consumables available (electrodes, nozzles); repair possible by a qualified technician |
| General information | Supplied with torch, ground clamp, cable and instruction manual |
Frequently Asked Questions - CUT-50 Vevor
What is the maximum cutting thickness of the CUT-50?
The CUT-50 can cut metals up to 12 mm in steel and 8 mm in stainless steel, with optimal cutting quality at lower thicknesses.
How do I adjust the cutting current on the CUT-50?
The current is adjusted using the rotary knob on the front panel. Turn it clockwise to increase the intensity (from 30 A to 50 A) depending on the type and thickness of the metal to be cut.
Can I use the CUT-50 without an air compressor?
No, plasma cutting requires compressed air to blow away the molten metal. You must connect an external compressor providing a pressure of 3 to 5 bar.
What type of mains power is required?
The device operates on a 230 V single-phase supply with a frequency of 50 Hz. Ensure that the power outlet is properly earthed.
What should I do if the thermal protection light comes on?
This light indicates overheating. Allow the device to cool down for a few minutes, check that the ventilation openings are not blocked, and reduce the duty cycle if necessary.
How do I replace an electrode or nozzle on the torch?
Unscrew the torch head, remove the worn electrode and nozzle, then install new ones. Tighten moderately and ensure the parts are properly aligned before welding.
What protective equipment should I wear?
Wear a welding helmet with a filter visor, heat-resistant insulating gloves, and protective clothing covering the arms and body to avoid burns.
Is the CUT-50 suitable for cutting aluminum?
Yes, it can cut aluminum but with a lower maximum thickness (about 5 to 6 mm) and a reduced cutting speed compared to steel.
How do I clean the device after use?
Unplug the device and let it cool down. Use a dry brush or a lint-free cloth to remove dust from the grilles. Never use water or solvent inside.
What should I do if the cut becomes irregular?
Check the condition of the electrode and nozzle (replace them if worn), ensure the air pressure is correct (3-5 bar) and the current is suitable for the metal thickness. A poor ground connection can also be the cause.
User questions about CUT-50 Vevor
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Welding machine in PDF format for free! Find your manual CUT-50 - Vevor and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. CUT-50 by Vevor.
USER MANUAL CUT-50 Vevor
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Vevor
Model : CUT-50
Category : Welding machine