ProLiant ML110 G6 - Server HP - Free user manual and instructions
Find the device manual for free ProLiant ML110 G6 HP in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type de produit | Server (Tower) |
| Brand | HP |
| Model | ProLiant ML110 G6 |
| Form Factor | Tower (5U) |
| Processor Socket | LGA1156 |
| Supported Processors | Intel Xeon X3400 series, Core i3, Pentium G6950, Celeron G1101 |
| Memory Type | DDR3 ECC UDIMM |
| Memory Slots | 4 (dual channel) |
| Maximum Memory | 16 GB |
| Internal Storage | 4 x 3.5-inch LFF SATA bays |
| Storage Controller | Embedded SATA controller with RAID 0/1/10 (optional add-on) |
| Expansion Slots | 1 x PCIe x16, 1 x PCIe x4, 1 x PCIe x1, 2 x PCI (32-bit/33MHz) |
| Networking | 2 x Gigabit Ethernet (NC107i) |
| Power Supply | 400W non-hot plug, 85% efficiency |
| Management | Integrated HP iLO 3 remote management |
| Cooling | 1 x rear system fan plus processor fan |
| Dimensions (W x D x H) | 20.0 x 58.0 x 42.4 cm (7.9 x 22.8 x 16.7 in) |
| Weight | 18 kg (39.7 lb) |
| Operating Temperature | 10°C to 35°C (50°F to 95°F) |
| Operating Humidity | 10% to 90% RH |
| Safety Features | Overheat protection, meets UL, CSA, CE standards |
| Maintenance | Tool-less side panel access; keep vents clean; use compressed air for dust |
| Repairability | Easy access to internal components, optional hot-swap drive bays |
Frequently Asked Questions - ProLiant ML110 G6 HP
What processors are compatible with the HP ProLiant ML110 G6?
The server supports Intel Xeon X3400 series, Core i3, Pentium G6950, and Celeron G1101 processors using the LGA1156 socket. Ensure BIOS is updated for optimal compatibility.
How much memory can I install in the ProLiant ML110 G6?
The system has 4 DIMM slots supporting up to 16 GB of DDR3 ECC UDIMM memory. For maximum performance, install matched pairs.
What RAID levels are supported?
The embedded SATA controller supports RAID 0, RAID 1, and RAID 10. For advanced RAID options, install an optional RAID controller in a PCIe slot.
How can I remotely manage the server?
The ProLiant ML110 G6 includes HP iLO 3 (Integrated Lights-Out 3) for remote management. Configure it through the BIOS or iLO setup utility to enable out-of-band management and virtual media.
Can I use non-ECC memory?
The system is designed for ECC UDIMM memory. Non-ECC memory may work in some configurations, but it is not recommended for critical server use and may cause stability issues.
How do I reset the administrator password?
To reset a forgotten password, use the iLO 3 virtual media to boot a password reset utility, or clear the CMOS via the motherboard jumper. Refer to the maintenance guide for specific jumper locations.
How many drives can I install?
The chassis has 4 internal 3.5-inch LFF SATA drive bays. Optional hot-swap cages are available for hot-plug drive support. Ensure adequate airflow when populating all bays.
What is the power supply rating?
The standard power supply is a 400W unit with 85% efficiency. It is non-hot-plug, so you must power down the server before replacing it.
How do I expand storage or add controllers?
The server provides 1 x PCIe x16, 1 x PCIe x4, 1 x PCIe x1, and 2 x PCI slots for adding RAID controllers, NICs, or other expansion cards.
What maintenance is required for optimal performance?
Regularly clean air vents and fans with compressed air to prevent dust buildup. Check for firmware updates on the HP website and apply them to ensure stability and security.
User questions about ProLiant ML110 G6 HP
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Server in PDF format for free! Find your manual ProLiant ML110 G6 - HP and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ProLiant ML110 G6 by HP.