ProLiant MicroServer G8 - Server HP - Free user manual and instructions
Find the device manual for free ProLiant MicroServer G8 HP in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product type | Microserver |
| Form factor | Ultra-micro tower |
| Processor | Intel Celeron G1610T (default), optional Intel Pentium or Xeon |
| Chipset | Intel C204 |
| Memory | 2 x DIMM slots, DDR3 UDIMM, up to 16 GB |
| Storage | 4 x LFF (3.5") SATA bays |
| Network | 2 x Gigabit Ethernet ports |
| Remote management | Integrated iLO4 with Remote Console |
| Expansion slots | 1 x PCIe 3.0 x16 (low profile) |
| Dimensions (W x D x H) | 20.7 x 24.9 x 23.5 cm |
| Weight | Up to 7.9 kg (maximum configuration) |
| Power supply | 150 W fixed power supply |
| Power input | 100-240 VAC, 50-60 Hz |
| Front I/O ports | 2 x USB 2.0, 1 x SD card slot |
| Rear I/O ports | 2 x USB 3.0, 1 x VGA, 2 x GbE, 1 x iLO port |
| Cooling | 1 x system fan (non-hot-plug, non-redundant) |
| Operating temperature | 10°C to 35°C |
| Noise level | 28 dB typical |
| Security | Lockable front bezel, chassis intrusion sensor |
| Repairability | User-accessible components, service manual provided |
| Energy efficiency | ENERGY STAR qualified |
Frequently Asked Questions - ProLiant MicroServer G8 HP
What is the maximum memory capacity of the HP ProLiant MicroServer G8?
The MicroServer G8 supports up to 16 GB of DDR3 UDIMM memory across its 2 DIMM slots. Both ECC and non-ECC modules are supported, but for maximum reliability, ECC memory is recommended.
Can I use standard SATA hard drives in the MicroServer G8?
Yes, the server has four LFF (3.5-inch) SATA bays that accept standard SATA drives. You can install non-hot-plug disks, and the server supports RAID configurations when using an optional controller.
What operating systems are supported by the ProLiant MicroServer G8?
The server supports a variety of operating systems, including Windows Server, Linux distributions (such as Ubuntu, CentOS), and VMware ESXi. Always check the official compatibility list for the latest supported versions.
How do I access the remote management interface (iLO)?
The server includes integrated iLO4 (Integrated Lights-Out 4). To access it, connect the network cable to the dedicated iLO NIC or use one of the shared NICs, then browse to the server’s IP address on port 443 (HTTPS). The default login is on the label on the server or found in the documentation.
What is the power consumption of the MicroServer G8?
The power consumption varies with configuration, but the 150 W power supply has a typical draw of around 30-50 W under normal load. It is designed for energy-efficient 24/7 operation.
How many hard drives can I install in the MicroServer G8?
You can install up to four 3.5-inch SATA hard drives in the front drive bays. Additionally, there is an internal USB port for booting and an optional slim optical drive slot.
Does the MicroServer G8 support ECC memory?
Yes, it supports ECC UDIMM (Unbuffered ECC) memory. Using ECC memory helps prevent data corruption, which is particularly important for a server environment.
How can I update the BIOS or UEFI firmware?
You can update the firmware using the HP Intelligent Provisioning tool or by downloading the latest system ROM from the HP support website. The update can be performed through the iLO interface or by booting from a USB drive.
Can I add a dedicated graphics card to the MicroServer G8?
Yes, the server has one PCIe 3.0 x16 slot that can accept a low-profile graphics card or other expansion cards. Note that the power supply is limited, so high-end GPUs are not recommended.
How do I reset the administrator password for the server or iLO?
To reset the iLO or system administrator password, you may need to clear the CMOS or use the iLO reset procedure. Refer to the service manual for the exact steps. Typically, you can power off, remove the battery for a few minutes, or use a jumper on the motherboard.
User questions about ProLiant MicroServer G8 HP
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Server in PDF format for free! Find your manual ProLiant MicroServer G8 - HP and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ProLiant MicroServer G8 by HP.
USER MANUAL ProLiant MicroServer G8 HP
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : HP
Model : ProLiant MicroServer G8
Category : Server