Total Iron 7200 Titan - Air purifier CECOTEC - Free user manual and instructions

USER MANUAL Total Iron 7200 Titan CECOTEC

1. Safety instructions 15
2. Parts and components 18
3. Before use 18
4. Operation 19
5. Cleaning and maintenance 22
6. Technical specifications 22
7. Disposal of old electrical appliances 23
8. Technical support service and warranty 23

SOMMAIRE

Fig./Img./Abb./Afb./Rys.1

Fig./Img./Abb./Afb./Rys. 2

Fig./Img./Abb./Afb./Rys. 3

Fig./Img./Abb./Afb./Rys. 4

Fig./Img./Abb./Afb./Rys. 5

ESPAÑOL

Read these instructions thoroughly before using the appliance. Keep this instruction manual for future reference or new users.

1. SAFETY INSTRUCTIONS

All safety instructions should be closely followed when using the appliance.

Make sure that the mains voltage matches the voltage stated on the rating label of the appliance and that the wall outlet is grounded.

Do not immerse the cord, plug, or any non-removable part of the appliance in water or any other liquid, nor expose the electrical connections to water. Make sure your hands are dry before handling the plug or switching on the appliance.

Warning: If the appliance falls accidentally in water, unplug it immediately. Do not reach into the water!

Do not twist, bend, strain, or damage the power cord in any way. Protect it from sharp edges and heat sources. Do not let it touch hot surfaces. Do not let the cord hang over the edge of the working surface.

The appliance is not intended to be operated by means of an external timer or separate remote-control system.

Turn off and unplug the appliance from the mains supply when not in use and before cleaning. Pull from the plug, not the cord, to disconnect it from the outlet.

This appliance is designed to iron textiles. It is designed for domestic use only and, therefore, not suitable for commercial use. Do not use it outdoors.

To protect against burns or injuries to persons, do not iron textiles while being worn on the body.

Do not use any accessory that has not been recommended by Cecotec, as they might cause injuries or damage.

ENGLISH

The appliance is not intended to be used by children under the age of 8. It can be used by children over the age of 8, as long as they are given continuous supervision.

This appliance is not intended to be used by persons with reduced physical, sensory, or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning the use of the appliance in a safe way by a person responsible for their safety, and understand the hazards involved.

Supervise young children to make sure that they do not play with the appliance. Close supervision is necessary when the appliance is being used by or near children.

Keep the appliance and its cord out of reach of children under the age of 8.

Place the appliance on a dry, stable, flat, heat-resistant surface.

The temperature of accessible surfaces may be high while in use and could cause burns. Do not touch hot surfaces while in use or immediately after.

Unplug the appliance immediately if fire or smoke is observed. Do not leave the appliance unattended while in use. Unplug it from the mains supply when you finish using it or when you leave the room.

The appliance must not be plugged in when filling or emptying the water tank.

The tank cap must not be open when the appliance is switched on.

The use of tap water is recommended. If the lime content of the tap water is too high, use a mix composed by 50 % of tap water and 50 % of water with low mineral content. Do not use only water with low mineral content.

Burns can occur when touching hot metal parts, hot water, or steam. Hot water may leak from the iron. Be careful when

ENGLISH

filling or turning the steam iron upside down.

To protect against burns or injuries, do not direct steam toward persons or animals when ironing.

The iron must be used and placed on a stable surface. When placing the iron on its stand, make sure that the surface is stable.

Keeping the iron at maximum temperature for too long may cause discolouration, which will not affect the performance of the appliance.

Do not try to repair the appliance by yourself. Contac the official Technical Support Service of Cecotec for advice.

Cleaning and maintenance must be carried out according to this instruction manual to make sure the appliance functions properly. Turn off and unplug the appliance before moving and cleaning it. Make sure the iron has completely cooled down before storing it.

Cleaning and maintenance tasks must not be carried out by children.

Store the appliance and its instruction manual in a safe and dry place when not in use.

Cecotec takes no responsibility for any damage caused by misuse of the appliance. Any misuse or non- compliance with these instructions renders the warranty and Cecotec's liability null and void.

If the power cord is damaged, it must be replaced by the Technical Support Service of Cecotec.

Warning: All our ironing range's products have undergone quality control tests previous to their commercialization. These tests consist of filling the water tank in order to check tightness and to ensure correct operating of the device. Once the test has been carried out, the tank is emptied and dried, but there is a slight probability that water could remain inside it.

TOTAL IRON 7000 STEAMPRO / STEAMPRO TOTAL IRON 7200 TITAN / TOTAL IRON 7500 TURBOSLIM

ENGLISH

2. PARTS AND COMPONENTS

Steam station

Fig. 1.

1. Steam toggle button
2. Clean button
3. Water spray button
4. Function indicator
5. Spray nozzle
6. Soleplate
7. Water inlet cover
8. Water tank
9. Cord winding groove
10. Unit base
11. Thermal insulation stand
12. Temperature dial
13. Temperature indicator
14. Handle
15. Steam trigger

Temperature dial

Fig. 2.

1. 170° C-225 ° C (Maximum)
2. 140 °C-210 °C
3. 100 °C-160 °C
4. 70 °C-120 °C (Minimum)

Buttons and indicators

Fig. 3.

1. Eco steam rate indicator
2. Clean indicator
3. Max. steam rate indicator
4. Water spray button
5. Steam toggle button
6. Clean button

3. BEFORE USE

Take the product out of the box.

Remove any packaging materials, stickers or protective foil from the soleplate.

18

TOTAL IRON 7000 STEAMPRO / STEAMPRO TOTAL IRON 7200 TITAN / TOTAL IRON 7500 TURBOSLIM

ENGLISH

Clean the soleplate with a soft cloth.

Fill the water tank with water and heat up the iron, and then iron over a piece of damp cloth for several minutes for the purpose of removing any residue on the soleplate.

Note: Some parts of the steam iron have been slightly greased and as a result, the iron may slightly smoke when switched on for the first time. After a short time, this will cease.

4. OPERATION

Water inlet cover

Open the water inlet cover and fill the water tank with water through the filling aperture.

Make sure the water does not exceed the MAX. mark on water tank.

Steam toggle button

The appliance can switch from MAX to ECO steam rates by pressing the steam toggle button. The default setting is the MAX steam rate when the appliance is turned on. Press the steam toggle button to select your desired steam rate, and the corresponding indicator of the selected steam rate will light up.

Temperature dial

Turn the temperature dial to set the desired ironing temperature based on the garment to be ironed. To activate the steam function, select the temperature range that steam is produced, otherwise water spray will not be emitted efficiently.

Temperature indicator

When the iron is heating up, the temperature indicator will turn on. Once the iron has reached the selected temperature, it will turn off. The temperature indicator will switch on and off as the iron maintains the selected temperature during ironing.

Steam trigger

When the appliance is heated to the selected temperature, press the steam trigger for steam to be sprayed from the soleplate continuously. Release the steam trigger to use the device for dry ironing without steam.

Steam burst

Fig. 4.

Quickly press the steam trigger twice to produce a burst of steam, and the indicator of MAX steam rate will blink. The Steam burst function can be only activated when the appliance is operated under MAX steam rate and the indicator of MAX steam rate is turned steady on.

TOTAL IRON 7000 STEAMPRO / STEAMPRO TOTAL IRON 7200 TITAN / TOTAL IRON 7500 TURBOSLIM

ENGLISH

Water spray button

Press the water spray button to activate the water spray function. The spray nozzle will spray water mist and wet the clothes that need to be ironed. Release the water spray button to stop the function.

Clean indicator

The appliance needs to be cleaned when the clean indicator lights up and remains on. It will blink when the appliance is being cleaned.

Clean button

Before activating the clean function, make sure the temperature dial is turned to the Max. setting and that the device is set to the steam mode. Press the steam trigger once for the water spray button to return to its original position.

The appliance must be cleaned when the clean indicator turns steady on. Before cleaning, prepare a container with a capacity of more than 300 ml for collecting the waste water.

Hold and press the "Clean button" for 2 seconds. When the buzzer sounds, the appliance will enter into the cleaning mode and the clean indicator will blink. The cleaning process will last for 3 minutes.

When the clean indicator turns off, if the user needs to perform another cleaning, hold and press the clean button for 5 seconds. When the buzzer sounds, the appliance will enter the cleaning mode and the clean indicator will blink. After about 3 minutes, the cleaning process will be completed.

Cord winding groove

When not in use, the steam supply hose and power cord can be wound along the cord winding groove for storage.

Fig. 5.

Note: The appliance will shut off automatically if all the indicators start blinking after being powered on, indicating the appliance has malfunctioned. Stop using the appliance and contact the Technical Support Service of Cecotec if this happens.

Dry ironing

Place the iron on the thermal insulation stand of the unit base.

Connect the plug to a wall outlet, the temperature indicator and the indicator of MAX. steam rate will turn on.

Turn temperature dial to select the desired temperature setting depending on the garment's fabric, the iron wills start heating up.

When the selected temperature is reached, the temperature indicator will turn off. Then, you can start ironing.

ENGLISH

WARNING: Always allow the device and especially its soleplate to cool completely down before touching or handling it.

Steam ironing

Note: To lengthen the appliance's service life, it is suggested to use purified water.

Put the unit base on a stable, flat surface.

Open the water inlet cover, fill the water tank with water through the filling opening. Do not exceed the MAX mark on the tank: 2L.

Place the iron on the thermal insulation stand of the unit base.

Connect the plug to a wall outlet, turn the temperature dial and the defaulted MAX steam rate indicator will turn steady on. Choose between MAX and ECO steam rate, select the desired steam rate for each garment according to your requirement. Make sure that there is enough water in the tank.

Turn temperature dial to select the desired temperature setting depending on the garment's fabric, the iron wills start heating up.

Ironing tips

Always check if the garment to be ironed has a label with ironing instructions and if they have, follow them.

If the fabric consists of various kinds of fibers, always select the lowest ironing temperature.

Synthetic fibre and silk fabrics should be ironed on their inner side to avoid them from being damaged.

Velvet and other textures that rapidly become shiny should be ironed in one direction with light pressure applied. Always keep the iron moving.

Pure wool fabrics (100% wool) may be ironed with the steam iron. Use a dry cloth as a mat and then select the corresponding fabric setting for ironing.

Never iron over zip, rivet in the cloth, this will damage the soleplate.

Before activating the clean function, make sure that the water in the tank is sufficient, and prepare a high temperature-resistant container to be placed under the soleplate for holding the dirty water sprayed from the steam hole of the soleplate during cleaning.

After a few minutes, the temperature indicator will turn off indicating the soleplate has reached the selected temperature and the iron is ready to use with steam.

Press the steam trigger to activate steam ironing. Release it to stop.

Note: Water may drip during spraying steam function when the temperature is set at the low settings.

Warnings:

Do not activate the steam button when the iron is placed on the unit base to avoid being scalded by steam.

After ironing, remove the plug from the wall socket, the appliance will turn off and all the

TOTAL IRON 7000 STEAMPRO / STEAMPRO TOTAL IRON 7200 TITAN / TOTAL IRON 7500 TURBOSLIM

ESPAÑOL

indicators will turn off too. Allow the whole unit to cool completely down before holding or storing it.

Setting	Temperature	Fabric
1	70 °C-120 °C	Acetate, elastane, polyamide, polypropylene
2	100 °C-160 °C	Cupro, polyester, silk
3	140 °C-210 °C	Triacetate, viscose, wool
Maximum	170 °C-225 °C	Cotton, flax

5. CLEANING AND MAINTENANCE

Turn off, unplug the appliance from the power supply, empty the water tank (do it after each use) and allow it to cool down completely.

Use a damp, soft cloth to clean the appliance's surface.

If there is any fabric adhered to the soleplate, use a damp cloth with vinegar to wipe off the soleplate.

Do not use abrasive scouring pads, powders or cleaners to clean the product.

If scale blocks the steam holes, use a toothpick to remove it.

If the appliance is not going to be used for a long time, pour out the water in the tank and store the iron on the thermal insulating cushion.

When not in use, the steam supply hose and power cord must be folded well and stored in their storage compartment.

6. TECHNICAL SPECIFICATIONS

05500 Total Iron 7000 Steam Pro

2000-2400 W, 220-240 V\~, 50-60 Hz, IXPO

05503 Total Iron 7200 Titan

2260-2700 W, 220-240 V\~, 50-60 Hz, IXPO

05504 Total Iron 7500 TurboSlim

2260-2700 W, 220-240 V\~, 50-60 Hz, IXPO

ENGLISH

7. DISPOSAL OF OLD ELECTRICAL APPLIANCES

The European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), specifies that old household electrical appliances must not be disposed of with the normal unsorted municipal waste. Old appliances must be collected separately, in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment.

The crossed out "wheeled bin" symbol on the product reminds you of your obligation to dispose of the appliance correctly. If the product has a built-in battery or uses batteries, they should be removed from the appliance and disposed of appropriately.

Consumers must contact their local authorities or retailer for information concerning the correct disposal of old appliances and/or their batteries.

8. TECHNICAL SUPPORT SERVICE AND WARRANTY

This product is under warranty for 2 years from the date of purchase, as long as the proof of purchase is submitted, the product is in perfect physical condition, and it has been given proper use, as explained in this instruction manual.

The warranty will not cover the following situations:

• The product has been used for purposes other than those intended for it, misused, beaten, exposed to moisture, immersed in liquid or corrosive substances, as well as any other fault attributable to the customer.
• The product has been disassembled, modified, or repaired by persons, not authorised by the official Technical Support Service of Cecotec.
- Faults deriving from the normal wear and tear of its parts, due to use.

The warranty service covers every manufacturing defects of your appliance for 2 years, based on current legislation, except consumable parts. In the event of misuse, the warranty will not apply.

If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact Cecotec Technical Support Service at [phone].

TOTAL IRON 7000 STEAMPRO / STEAMPRO TOTAL IRON 7200 TITAN / TOTAL IRON 7500 TURBOSLIM

FRANÇAIS

Quart de Poblet, Valencia (Spain)

LB01191029

POLSKI

TOTAL IRON 7000 STEAMPRO / STEAMPRO TOTAL IRON 7200 TITAN / TOTAL IRON 7500 TURBOSLIM

POLSKI

TOTAL IRON 7000 STEAMPRO / STEAMPRO TOTAL IRON 7200 TITAN / TOTAL IRON 7500 TURBOSLIM