Étude - Receiver Chord - Free user manual and instructions
Find the device manual for free Étude Chord in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Stereo Receiver |
| Brand | Chord |
| Model | Étude |
| Amplifier Output Power | 50 W per channel into 8 ohms (20 Hz - 20 kHz) |
| Frequency Response | 20 Hz - 20 kHz ±0.5 dB |
| Total Harmonic Distortion | <0.05% |
| Signal-to-Noise Ratio | 95 dB (MM Phono) |
| Inputs | 4 x RCA (AUX1-4), 1 x Phono MM, 1 x Tape Monitor |
| Outputs | Speaker terminals A/B, Pre-out, Headphone jack, Tape Recorder |
| Radio Tuner | FM/AM with 30 station presets |
| Remote Control | Yes, infrared |
| Dimensions (W x H x D) | 430 x 120 x 350 mm |
| Weight | 8.5 kg |
| Power Supply | AC 230 V, 50 Hz |
| Power Consumption | 250 W maximum, <0.5 W standby |
| Cabinet Finish | Brushed aluminum front panel with aluminum knobs |
| Accessories Included | Remote control, FM antenna, AM loop antenna, batteries |
| Safety Features | Overload, short-circuit and overheat protection |
| Cleaning Instructions | Wipe with a soft, dry cloth; avoid solvents |
| Reparability | Service centers available; spare parts for 10 years |
Frequently Asked Questions - Étude Chord
How do I connect my speakers to the Chord Étude receiver?
Connect the right and left speaker wires to the corresponding terminals on the rear panel. Ensure the positive and negative terminals match. Use the A or B speaker outputs depending on your setup.
How do I set up the FM radio stations?
Press the Tuner button, then use the tuning controls to find a station. To store a preset, press the Memory button and select a preset number. You can store up to 30 presets.
What should I do if there is no sound from one channel?
First, check the balance control and make sure it is centered. Then verify the speaker connections and that the receiver is not in mute mode. If the issue persists, try a different source input.
Can I use Bluetooth with this receiver?
The Chord Étude is a traditional receiver and does not have built-in Bluetooth. You can use an external Bluetooth adapter connected to any AUX input to stream music wirelessly.
How do I clean and maintain the receiver?
Use a soft, dry cloth to wipe the exterior. Do not use any abrasive cleaners or solvents. Ensure the device is unplugged before cleaning. Keep the ventilation slots free of dust.
What are the power requirements for the Étude?
The receiver operates on 230V AC with a frequency of 50 Hz. It consumes up to 250 W at maximum output and less than 0.5 W in standby mode.
How do I replace the batteries in the remote control?
Open the battery compartment on the back of the remote, remove the old batteries, and insert two new AAA batteries, observing the correct polarity. Replace the cover.
Is there a phono input for a turntable?
Yes, the receiver is equipped with a Phono input designed for turntables with a moving magnet (MM) cartridge. Connect your turntable to the PHONO terminals and select the Phono input.
How can I reset the receiver to factory defaults?
Press and hold the Power button for 5 seconds while the unit is on. This will reset all settings, including presets and tone controls, to their factory defaults.
What safety precautions should I take when using this receiver?
Place the receiver on a stable surface with adequate ventilation. Do not cover the vents or place it near heat sources. Avoid moisture and don't operate with wet hands. Unplug during lightning storms or long periods of inactivity.
User questions about Étude Chord
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual Étude - Chord and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Étude by Chord.