MQV-2D-F - Fastening tool HILTI - Free user manual and instructions
Find the device manual for free MQV-2D-F HILTI in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Direct fastening tool (powder-actuated) |
| Brand | Hilti |
| Model | MQV-2D-F |
| Application | Fastening into concrete and structural steel |
| Fastener Range | Pin length from 10 to 30 mm |
| Magazine Capacity | 10 fasteners |
| Power Source | Powder cartridges (6.8/11 M) |
| Driving Mechanism | Semi-automatic, single-shot |
| Depth Adjustment | Stepless with control knob |
| Weight | 2.4 kg (with magazine) |
| Dimensions (L x H x W) | 390 x 170 x 75 mm |
| Handle | Ergonomic composite handle with slip-resistant coating |
| Safety Features | Contact pressure trigger, drop safety, protective shroud |
| Noise Level | 94 dB A (at operator ear) |
| Vibration Level | 2.1 m/s² (typical) |
| Cartridge Type | 5/11 M or 6.8/11 M strips |
| Operating Temperature | -10°C to +50°C |
| Maintenance | Regular cleaning of piston, sleeve and breech; light lubrication |
| Spare Parts | Piston, buffer ring, cartridge guide, trigger spring |
| Standards | CE compliant, PTB approved |
Frequently Asked Questions - MQV-2D-F HILTI
What type of cartridges does the Hilti MQV-2D-F use?
The MQV-2D-F uses 6.8/11 M powder cartridges in strip form. Always use Hilti cartridges for optimal performance and safety.
Can I use this tool for both concrete and steel fastening?
Yes, the MQV-2D-F can fasten into concrete and structural steel. Choose the right fasteners and cartridge power level for each base material.
How do I adjust the driving depth?
Turn the adjustment knob at the front of the tool to set the driving depth. Test on a sample area and start with a lower power setting, then increase gradually.
What maintenance does the tool require?
Regularly clean the piston, barrel and breech after each session. Apply a thin layer of lubricant to moving parts. Check the buffer for wear and replace when necessary.
Is the MQV-2D-F heavy or difficult to operate?
The tool weighs about 2.4 kg and features an ergonomic, slip-resistant handle. The trigger requires a light pull, and the tool is well balanced for single-handed operation.
What safety features are included?
The tool is equipped with a contact pressure device that prevents firing unless the tool is fully pressed against a work surface. There is also a drop safety mechanism and a protective shroud to deflect debris.
How often should I replace spare parts?
Inspect the piston and buffer every few thousand fastenings. Replace them if you notice cracked parts or reduced driving power. Use genuine Hilti spare parts to maintain warranty.
Can the tool be used in cold weather?
The operating temperature range is -10°C to +50°C. In very cold conditions, keep cartridges in a warm place and avoid moisture. Performance may vary slightly at extreme temperatures.
What is the maximum fastener length?
The recommended fastener length for the MQV-2D-F is 10 to 30 mm depending on the base material and application. Never exceed 30 mm without consulting the full user manual.
Where can I find a user manual for the MQV-2D-F?
You can download the user manual in PDF format for free from notices-facile.com. The manual is available in English and other languages. For detailed instructions, you can also contact Hilti support.
User questions about MQV-2D-F HILTI
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Fastening tool in PDF format for free! Find your manual MQV-2D-F - HILTI and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. MQV-2D-F by HILTI.
USER MANUAL MQV-2D-F HILTI
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : HILTI
Model : MQV-2D-F
Category : Fastening tool