BOAC-1-1/2 - Water pump Truper - Free user manual and instructions
Find the device manual for free BOAC-1-1/2 Truper in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product type | Centrifugal water pump for domestic use |
| Brand | Truper |
| Model | BOAC-1-1/2 |
| Power | 1.5 HP (approximately 1.1 kW) |
| Power supply | 127 V, 60 Hz, single-phase |
| Current consumption | 5.5 A |
| Maximum flow rate | 110 L/min |
| Maximum lift height | 33 m |
| Maximum suction depth | 8 m |
| Suction and discharge connections | 1.5" (38 mm) NPT |
| Body material | Cast iron |
| Impeller material | Bronze |
| Mechanical seal | Carbon and ceramic |
| Approximate dimensions | 25 x 30 x 20 cm |
| Approximate weight | 11 kg |
| Recommended use | Pumping clean water for domestic use, irrigation, and filling water tanks |
| Maintenance | Periodic cleaning of the strainer, inspection of the mechanical seal, and lubrication of bearings |
| Safety | Do not run dry, connect to a grounded outlet, and use a residual current circuit breaker |
| Spare parts | Available at Truper authorized service centers |
| Warranty | Years |
Frequently Asked Questions - BOAC-1-1/2 Truper
Can I use the pump to extract water with sand or sediments?
No, this pump is designed to pump clean water without abrasive particles. Sand can damage the impeller and the mechanical seal, reducing the equipment's lifespan.
How do I prime the pump before turning it on?
Remove the filler cap, pour water through the suction or filler port until the body is full, and then replace the cap before starting. This prevents the pump from running dry.
What voltage does this pump need?
The pump operates with 127 V and 60 Hz, which is the standard domestic supply in Mexico. Ensure the electrical installation complies with current regulations.
What is the maximum flow rate it can handle?
The maximum flow rate is 110 liters per minute, measured with suction and discharge under optimal conditions. This value may vary depending on the height and length of the hoses.
How should it be installed correctly?
It should be installed on a firm and level surface, near the water source, with short suction pipes and no air leaks. The discharge must be open when first turned on. Connect to ground and protect with a residual current circuit breaker.
What periodic maintenance does it require?
Check the suction strainer and clean it of impurities. Every 3 to 6 months, inspect the mechanical seal and electrical connectors. Drain the water if the pump will not be used for a long time.
Is it suitable for filling a swimming pool?
Yes, it is suitable for filling or emptying pools as long as the water is clean. It is recommended to use an additional strainer to prevent leaves or large debris from entering.
What to do if the pump does not start?
Check the electrical power supply (fuses, circuit breaker), make sure the pump is full of water and not blocked by particles. If the problem persists, contact an authorized technical service.
What is the maximum suction height?
The theoretical maximum suction height is 8 meters. For proper operation, it is recommended not to exceed 6 meters and keep the suction hose as short as possible.
Where can I buy spare parts for this pump?
Original spare parts are available at Truper authorized service centers or official distributors. Always use original parts to ensure performance and warranty.
User questions about BOAC-1-1/2 Truper
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Water pump in PDF format for free! Find your manual BOAC-1-1/2 - Truper and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. BOAC-1-1/2 by Truper.
USER MANUAL BOAC-1-1/2 Truper
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Truper
Model : BOAC-1-1/2
Category : Water pump