ProLiant SL230s G8 - Server HP - Free user manual and instructions
Find the device manual for free ProLiant SL230s G8 HP in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Scale-out rack server |
| Brand | HP |
| Model | ProLiant SL230s Gen8 |
| Form Factor | Half-width 1U rack mount |
| Processor | Two Intel Xeon E5-2400 series sockets |
| Chipset | Intel C600 series |
| Memory Slots | 12 DIMM slots supporting DDR3 ECC |
| Maximum Memory | Up to 384 GB depending on DIMM size |
| Drive Bays | Up to 8 SFF (2.5-inch) hot-plug drive bays |
| Storage Controller | HP Smart Array B320i embedded controller |
| Network | 1 GbE dual-port LAN integrated |
| Expansion Slots | 1 mezzanine PCIe 3.0 slot |
| Management | HP iLO4 with remote console |
| Power Supply | Redundant hot-plug power supplies |
| Cooling | Active system fans with fault tolerance |
| Security | TPM support, chassis intrusion detection |
| Operating Temperature | 10°C to 35°C |
| Dimensions | 1U half-width: 44.4 x 21.6 x 61.5 cm (H x W x D) |
| Weight | Approximately 14 kg |
| Maintenance | Clean air vents with compressed air; no liquid cleaners |
| Repairability | Hot-plug PSU, fans, and drives; tool-free access to internal components |
Frequently Asked Questions - ProLiant SL230s G8 HP
How do I reset the Administrator password on the HP ProLiant SL230s Gen8?
To reset the BIOS Administrator password, power off the server, remove the access panel, and locate the system board jumper labeled NVRAM_CLR or Password. Move the jumper to the clear position for 5 seconds, then restore it. Reassemble and power on; the password is cleared.
What type of memory does the SL230s Gen8 support?
The ProLiant SL230s Gen8 supports DDR3 Registered ECC (RDIMM) and Unbuffered ECC (UDIMM) memory. It has 12 DIMM slots and can accept 1.5V and 1.35V modules. Use HP-qualified memory for best performance and reliability.
Can I install non-HP drives in this server?
Yes, the SATA ports accept industry-standard SATA drives. However, for optimal support and warranty, HP recommends using HP-qualified drives. If you use third-party drives, you may lose some management and predictive failure features.
How do I configure RAID on the embedded Smart Array controller?
During POST, press F5 to enter Option ROM Configuration for Arrays (ORCA). From there you can create and manage logical drives. Alternatively, boot into HP Intelligent Provisioning and use the Smart Storage Administrator for more advanced configuration.
How do I access the iLO management port?
Connect a network cable to the dedicated iLO management port (marked with a wrench icon) and use a web browser to access the default IP address 192.168.2.2 (or DHCP-assigned). The default login is Administrator with the password set during initial setup.
What is the maximum number of CPUs supported?
The SL230s Gen8 supports up to two Intel Xeon E5-2400 series processors. It requires both processors to access all memory channels; a fully populated system uses two CPUs.
Does the server support hot-plug power supplies?
Yes, the system supports redundant hot-plug 460W, 500W, or 750W power supplies (depending on SKU). You can replace a failed PSU without powering off the server, provided the other PSU is connected to an active power source.
How can I update the BIOS/firmware?
Use HP Smart Update Manager (SUM) or the HP Intelligent Provisioning recovery media to apply the latest firmware from HP's support website. You can also update via iLO using the integrated remote console.
How do I identify the health of the server using LEDs?
The front panel has system health LED (green/amber/red). A solid green indicates normal operation. A flashing or solid amber indicates a degraded state; red indicates a critical failure. Use the iLO Event Log for detailed errors.
What are the recommended cleaning procedures?
Clean the server exterior with a soft, lint-free cloth. Use compressed air to blow dust out of fans and heat sinks. Avoid liquid cleaners and never spray directly on the board. For persistent dust, power down and use a vacuum with ESD protection.
User questions about ProLiant SL230s G8 HP
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Server in PDF format for free! Find your manual ProLiant SL230s G8 - HP and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ProLiant SL230s G8 by HP.
USER MANUAL ProLiant SL230s G8 HP
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : HP
Model : ProLiant SL230s G8
Category : Server