Ortofon 2M - Uncategorized Fluance - Free user manual and instructions
Find the device manual for free Ortofon 2M Fluance in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Phono Cartridge (Moving Magnet) |
| Brand | Fluance |
| Model | Ortofon 2M |
| Mount Type | Standard 1/2-inch mount |
| Output Voltage | 5.5 mV (at 1 kHz, 5 cm/sec) |
| Frequency Response | 20 Hz – 20 kHz |
| Tracking Force | 1.8 g (recommended), 1.6–2.0 g range |
| Stylus Type | Elliptical diamond |
| Stylus Replacement | User-replaceable, Ortofon 2M series styli |
| Cartridge Weight | 7.2 g |
| Dimensions | 19.5 x 16.5 x 4.5 mm (approx.) |
| Power Supply | Passive, no external power required |
| Channel Separation | 22 dB at 1 kHz |
| Channel Balance | 1.5 dB at 1 kHz |
| Recommended Load Resistance | 47 kΩ |
| Recommended Load Capacitance | 150–300 pF |
| Compliance | 15 µm/mN (dynamic) |
| Tracking Ability | 150 µm |
| Warranty | 1 year limited warranty |
| Package Includes | Cartridge, mounting screws, stylus guard |
Frequently Asked Questions - Ortofon 2M Fluance
How do I install the Ortofon 2M cartridge on my tonearm?
To install, attach the cartridge to the headshell using the two mounting screws. Use a protractor to align the stylus tip with the alignment grid, then adjust the overhang and offset angle as per the manufacturer's specifications.
What is the correct tracking force for this cartridge?
The recommended tracking force is 1.8 g. You can set it by rotating the counterweight on your tonearm while using a tracking force gauge. The acceptable range is 1.6–2.0 g.
How do I align the cartridge correctly?
Use an alignment protractor supplied with most turntables. Position the protractor over the platter, adjust the cartridge position in the headshell until the stylus tip precisely follows the grid at both null points. Tighten the screws after alignment.
How should I clean the stylus?
Use a carbon fiber brush or a stylus cleaning solution. Gently brush the stylus from the back to the front to remove dust and debris. Never touch the stylus with your fingers.
Can I replace the stylus myself?
Yes, the stylus is user-replaceable. To replace it, gently pull the old stylus forward and downward, then push the new stylus into the cartridge body until it clicks into place. Ensure the stylus guard is on during handling.
Which turntables are compatible with this cartridge?
The cartridge fits any turntable with a standard 1/2-inch mount headshell. It is commonly used with Fluance RT83 and other turntables that accept moving magnet cartridges.
What is the difference between Ortofon 2M Red and Blue?
The 2M Red features an elliptical diamond stylus, while the 2M Blue uses a nude elliptical stylus for improved tracing and detail. The Blue also has a slightly different generator system, offering higher performance.
How do I handle the cartridge to avoid damage?
Always handle the cartridge by its body to avoid bending the cantilever or damaging the stylus. Use the stylus guard when transporting or storing the turntable.
What is the recommended load impedance for my phono preamp?
The cartridge works best with a 47 kΩ load resistance and 150–300 pF capacitance. Most modern phono stages comply with this standard. Check your preamp's specifications.
How should I store the turntable when not in use?
Keep the stylus guard in place and cover the turntable to avoid dust. Store in a dry, temperature-controlled environment to prevent corrosion and ensure optimal performance.
User questions about Ortofon 2M Fluance
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual Ortofon 2M - Fluance and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Ortofon 2M by Fluance.