SDBT-BSW-1L-PU-W-0.3-N-M12 - Sensor Festo - Free user manual and instructions
Find the device manual for free SDBT-BSW-1L-PU-W-0.3-N-M12 Festo in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Magnetic Cylinder Sensor |
| Model | SDBT-BSW-1L-PU-W-0.3-N-M12 |
| Brand | Festo |
| Dimensions (HxWxD) | 26 mm x 6 mm x 5 mm (approx.) |
| Weight | 10 g (approx.) |
| Supply Voltage | 10-30 V DC |
| Switching Output | NPN, normally open |
| Max. Output Current | 100 mA |
| Connection | M12 connector, 3-pin |
| Cable Length | 0.3 m (PUR) |
| LED Indicator | Yes, for output status |
| Protection Class | IP67 |
| Operating Temperature | -25 °C to +70 °C |
| Mounting | Insertable into T-slot (size 8 mm) |
| Material (Housing) | Polyamide (PA) with PUR cable |
| Maintenance | Clean with a dry, lint-free cloth; avoid solvents |
| Safety | Do not exceed specified voltage; avoid mechanical stress on cable |
| Spare Parts / Repairability | Not repairable; replace entire unit if defective |
| General Information | Compatible with Festo cylinders with T-slot; red LED indicates switching state |
Frequently Asked Questions - SDBT-BSW-1L-PU-W-0.3-N-M12 Festo
How do I wire the SDBT-BSW-1L-PU-W-0.3-N-M12 sensor?
The sensor has a 3-pin M12 connector. Pin assignments: pin 1 (brown) = +10-30V DC, pin 3 (blue) = 0V, pin 4 (black) = NPN switching output. Refer to the wiring diagram in the manual.
What is the sensing range of this sensor?
The sensor detects the magnetic field of a piston magnet. Detection range is typically up to 5 mm from the sensor face, depending on the cylinder type.
Can I use this sensor with any cylinder?
It is designed for T-slot cylinders with an 8 mm slot width. It fits Festo cylinders (e.g., DSNU, ADN) and compatible brands. Ensure the cylinder has a magnetic piston.
What does the LED indicate?
The red LED illuminates when the sensor detects the magnetic field and the output is active (NPN transistor conducts).
Is the sensor short-circuit protected?
Yes, the sensor has short-circuit protection and reverse polarity protection on the supply voltage.
What is the maximum cable length I can extend?
The built-in cable is 0.3 m. For extension, use a M12 extension cable. Total cable length should not exceed 30 m to avoid voltage drop and signal degradation.
How do I mount the sensor?
Insert the sensor into the T-slot of the cylinder from the end. Push it until it clicks into place. Ensure the sensor is oriented correctly with the LED visible.
Can I use this sensor in a washdown environment?
Yes, with IP67 protection it is resistant to dust and temporary immersion in water. However, avoid high-pressure spray directly on the connector.
What is the switching frequency?
The sensor has a switching frequency of up to 1 kHz, suitable for most pneumatic applications.
Where can I find the datasheet?
The official datasheet and user manual are available on the Festo website or via notice-facile.com for your model.
User questions about SDBT-BSW-1L-PU-W-0.3-N-M12 Festo
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Sensor in PDF format for free! Find your manual SDBT-BSW-1L-PU-W-0.3-N-M12 - Festo and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SDBT-BSW-1L-PU-W-0.3-N-M12 by Festo.
USER MANUAL SDBT-BSW-1L-PU-W-0.3-N-M12 Festo
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Festo
Model : SDBT-BSW-1L-PU-W-0.3-N-M12
Category : Sensor