Energysilence Aero 3600 Invisible Metalic Style - Ceiling fan CECOTEC - Free user manual and instructions

Product type	Ceiling fan
Brand	Cecotec
Model	Energysilence Aero 3600 Invisible Metallic Style
Color	Silver metal
Diameter	91 cm
Height	30 cm
Weight	5.8 kg
Power supply	220-240 V, 50 Hz
Power	45 W
Number of speeds	3
Reverse function	Yes (winter/summer)
Noise level	< 35 dB
Remote control	Yes (included)
Blade material	Metal and plastic
Number of blades	3 (retractable)
Tilt angle	12°
Airflow	150 m³/min
Installation	On ceiling (mounting required)
Maintenance	Clean with a soft cloth
Safety	Use a differential switch
Spare parts	Available on Cecotec website
Warranty	2 years

Frequently Asked Questions - Energysilence Aero 3600 Invisible Metalic Style CECOTEC

How to install the ceiling fan?

Installation requires fixing the bracket to the ceiling with suitable anchors, then connecting the electrical wires according to the provided diagram. It is recommended to call an electrician if you have no experience.

The remote control does not work, what to do?

First check the batteries of the remote control. Then ensure that the receiver is properly connected. If the problem persists, reset the remote control following the procedure described in the manual.

How to reverse the rotation direction of the fan?

Use the reverse button on the remote control or on the fan housing. In summer, the blades rotate counterclockwise to create a cooling breeze; in winter, clockwise to redistribute heat.

How to clean the fan blades?

Turn off the fan and use a slightly damp soft cloth to wipe the blades. Avoid abrasive products that could damage the metallic finish.

The fan is making noise, is it normal?

The Energysilence Aero 3600 model is designed to be silent (<35 dB). If you hear abnormal noise, check that the blade screws are tight and the balance is correct.

What is the recommended ceiling height?

The minimum recommended height is 2.30 meters from floor to ceiling to ensure optimal safety. The fan must be installed at least 30 cm from the ceiling.

Can I use the fan without the remote control?

Yes, the fan has a wall switch (not included) that allows turning on/off and changing speed manually. The remote control offers more convenience.

How to synchronize the remote control with the fan?

Synchronization occurs automatically after power on. If it fails, turn off the power for 10 seconds, then restore it. Then press the 'Pair' button on the remote control.

What to do if the fan does not rotate?

Check the fuses and circuit breaker. Ensure the wiring is correct. If the motor is stuck, try to turn it manually. Contact customer service if the problem persists.

Does the fan consume a lot of electricity?

With a power of 45 W, this fan is very economical. It consumes approximately 0.045 kWh per hour at maximum speed, less than a standard light bulb.

USER MANUAL Energysilence Aero 3600 Invisible Metalic Style CECOTEC

Safety instructions 7

1. Parts and components 45

2. Before use 45

3. Assembling the appliance 46

4. Cleaning and maintenance 50

5. Troubleshooting 51

6. Technical specifications 52

7. Disposal of old electrical and electronic appliances 53

8. Technical support and warranty 53

9. Copyright 53

SOMMAIRE

Read these instructions thoroughly before using the device. Keep this instruction manual for future reference or new users.

- This appliance can be used by children aged 8 years and above and people with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children must not play with the appliance. Cleaning and user maintenance should not be carried out by unsupervised children.

- Keep a minimum distance of 2.3 cm between the fan blades and the floor.

- Keep a minimum distance of 76 cm between the fan blades and the wall or any other object.

- Make sure the appliance is unplugged from the power supply

before cleaning or user maintenance.

• This device is designed for domestic use only and is not intended for bars, restaurants, farmhouses, hotels, motels, and offices.
• Make sure that the mains voltage matches the voltage stated on the appliance marking and that the wall outlet is earthed.
• If the power cord is damaged, it must be replaced by the official Cecotec Technical Support Service to avoid any type of danger.
• Do not use the appliance if its cord or housing are damaged, nor after it malfunctions or has been dropped or damaged in any way.
• The appliance must be installed in accordance with national wiring regulations.
• Never insert objects or body parts between the rotating fan blades.
• To reduce the risk of injury, attach the fan directly to the support structure of the building as indicated in this manual and use only parts and components provided and recommended by Cecotec.
• Cut off the power completely before installing or repairing the fan to avoid the risk of electric shock.
• The electrical wiring must be in accordance with the local regulations.
• The cable must be properly earthed to avoid possible accidents.
• The appliance must be installed in accordance with national wiring regulations.
• Never install the fan in a damp or wet room.
• Be careful when near the rotating fan blades.

• To adjust the speed of the fan blades, only use the means for speed control provided by Cecotec.

• Do not bend the blade-attachment system during the installation or cleaning process.

• Cleaning and maintenance must be carried out according to this instruction manual to make sure the appliance works properly. Turn off and unplug the appliance before cleaning it.
• Make sure the fan is not placed close to curtains or other objects it may become entangled with.
• In order to ensure your children's safety, please keep all packaging (plastic bags, boxes, polystyrene, etc.) out of their reach.
• It is recommended that two people install the appliance.
• This appliance is designed for indoor use.

Instructions on batteries

• Battery ingestion can cause burns, soft-tissue perforation, and death. It can cause severe burns within two hours of the ingestion.
• In case of battery ingestion, please seek medical attention immediately.
• Do not allow children to replace batteries without adult supervision.
• Do not disassemble, open, or damage the batteries.
• Keep the batteries out of the reach of children. Pay particular attention to small batteries. In case of battery ingestion, please seek medical attention immediately.
• Do not expose batteries to heat or fire. Avoid storage in direct sunlight.
• Do not short-circuit an element or a battery. Do not store batteries in an untidy manner, in a box, or drawer where they can short-circuit each other or be short-circuited by other metal objects.
• Both batteries and cells can leak under extreme conditions.

In the event of a battery leak, keep your skin and eyes away from the liquid. If the liquid gets into contact with skin, wash immediately with soap and water. If the liquid gets into the eyes, wash them immediately with clean water for a minimum of 10 minutes and seek medical attention. Wear gloves to handle the battery and dispose of it immediately in accordance with local regulations.

• Pay attention to the positive (+) and negative (-) marks on the batteries and the remote-control compartment to ensure they are inserted correctly.
• Do not use any batteries that are not designed for use with the appliance.
• Do not mix batteries of different manufacture, capacity, or size. Children should be allowed to handle the batteries only under adult supervision.
• Always buy recommended batteries.
• Keep the batteries clean and dry. Wipe the battery terminals with a clean, dry cloth if they become dirty.
• Keep the original instruction manual for future reference.
• Whenever possible, remove the batteries when not in use.

INSTRUCTIONS DE SÉCURITÉ

Number	Description	No. of rolls
1	Mounting bracket	1
2	Hanging ball	1
3	Downrod	1
4	Canopy	1
5	Canopy screws	2
6	Clevis pin	1
7	Stop pin clip	1
8	Downrod cover	1
9	Motor assembly	1
10	Lamp bracket	1
11	Lampshade	1
12	Remote control	1
13	Receiver	1

NOTE:

The graphics in this manual are schematic representations and may not exactly match the device.

2. BEFORE USE

• This appliance is packaged in a way as to protect it during transport. Take the device out of its box and remove all packaging materials. You can keep the original box and other packaging elements in a safe place. This will help you prevent damage to the device when transporting it in the future. In case the original packaging is disposed of, make sure all packaging materials are recycled accordingly.
• Make sure all parts and components are included and in good conditions. If there is any piece missing or in bad conditions, contact the official Cecotec Technical Support Service immediately.

ENGLISH

Box content

• Fan
• Assembly kit
• Remote control
• 2 AAA batteries
• Instruction manual

3. ASSEMBLING THE APPLIANCE

Wooden ceiling

Secure the mounting bracket firmly to the wooden ceiling beam with a drill bit (Figure 2).

Concrete ceiling

• You can enlarge the holes in the mounting bracket with a medium 8 mm drill bit.
• Use the M6 expansion bolts to attach the mounting bracket to the side of the screw hook.
• The distance between the screw hooks and the mounting bracket must be between 8 and 10 mm. The installation of the screw hook must not interfere with the mounting bracket and must not affect the positioning of the receiver (Figure 3).

Fig. 3 key:

Concrete ceiling

1. Expansion bolt
2. Screw hook
3. Drilling diagram

Safety rope installation

1. Loosen the screw on the locking side of the wire rope, place the wire rope ring on the hook of the expansion bolt, tension the wire rope, and then tighten the wire rope locking screw. (Fig. 4)
2. Connect the cable according to the wiring instructions in the wiring diagram, as shown in Fig. 5

Fig. 5 key

L: Live wire

N: Neutral

Earth wire

Fan installation

1. Unpack the ceiling fan carefully, remove all parts and components and place it on a cloth or

soft surface to prevent damage. Do not lay the motor housing on its sides to avoid damage to the housing. Before starting the installation, check that no parts are missing.

Warning: to avoid electric shock, all electrical operations should only be carried out after disconnecting the power by removing the fuses or turning off the circuit breaker.

1. In case of installing the ceiling fan to a wooden beam, 4 self-tapping screws should be enough to support the weight (Fig. 6).
2. Screw the mounting bracket to the ceiling and make sure all connections are secure to prevent the fan from falling. Loosen the two canopy screws from the mounting bracket.

Note: self-tapping screws are only suitable for wooden ceilings. In case of installing the ceiling fan to concrete ceilings or joists, use a drill for making the holes and stoppers or expansion bolts (not included).

1. Loosen the hanging ball screws until the ball slides down the downrod. Remove the downrod pin (Fig. 7).

Fig. 7 key

1. Hanging ball
2. Pin

3. Loosen screw

4. Remove the pin and the pin clip from the downrod. Slide the downrod through the canopy and the downrod cover (Fig. 8).

5. Loosen the screws of the mounting bracket and then place the downrod in the mounting bracket.
6. Pass the fan wires and the earth wire through the downrod. (Fig. 9) Align the holes in the clevis pin of the downrod with the holes in the bracket.

Note: make sure to insert the straight part of the clevis pin through the hole in the end of the clevis pin and press until the crimped part snaps into position.

1. Finally, retighten the screws.

Warning: it is very important that the mounting bracket pin is correctly installed and that the screws are tightened securely. If the pin, clevis, or screws are not correctly positioned, the fan may fall down.

1. Hang the fan on the mounting bracket (Fig. 10).
2. Fix the lamp bracket to the motor with 3 screws and then fix the lampshade with 4 screws

ENGLISH

(Fig. 11).

Note: after installation, check that all parts are securely fixed.

Please note: before fitting the bulb, make sure that the fan is not connected to the mains.

11. Connect the wires as follows:

Figure 12

• Plug the receiver into the bracket with the flat side up.
• Insert the 3P connector of the bracket into the AC POWER INPUT socket of the receiver.
• Insert the 2P light connector from the fan motor assembly into the 2P LIGHT socket on the receiver.
• Insert the 3P connector of the fan motor into the 3P MOTOR socket of the receiver.
• Connect the yellow/green 1P connectors of the fan motor assembly and the suspension bracket.

12. Mount the canopy as shown above (Fig. 13).

Remote control

Fig. 14

1. Reconnect the mains supply from the electrical switchboard in the house.
2. Remove the battery-compartment cover of the remote control, insert the batteries, and replace the cover.

Note:

• The remote control is powered by two AAA 1.5 V batteries.
• If the fan is not to be used for a long period of time, store the remote control in a dry place where it will not be exposed to heat or direct sunlight. Also remove the batteries.
• The remote-control buttons control the speed and light of the fan.

Fig. 14 key

1. Power button (used to pair the remote control)
2. Clockwise rotation
3. Switch off the fan only
4. Light button
5. Counterclockwise rotation
6. Natural-breeze mode
7. Setting the speed
8. Timer
   2H: the fan will automatically switch off after two hours of operation.
   4H: the fan will automatically switch off after four hours of operation.
   8H: the fan will automatically switch off after eight hours of operation.

Note:

• The remote control is powered by two AAA 1.5 V batteries.
• If the fan is not to be used for a long period of time, store the remote control in a dry place where it will not be exposed to heat or direct sunlight. Also remove the batteries.
• The remote-control buttons control the speed and light of the fan.

To start the fan, use the remote control.

• Use the speed buttons to select the air power level.
• Use the timer buttons to select the fan operating time. The fan will switch off once the selected time has elapsed.
• Press the light button to turn the fan's lamp on and off.

Winter Function

Press button 2 to activate the winter function. The fan will make air flow from the bottom upwards, bringing cold air to the top of the room.

Summer Function

Press button 5 to activate the summer function. The fan will make air flow from the top downwards, bringing cold air to the bottom of the room.

Natural breeze

Activate this mode by pressing button 6. The fan will progressively vary the power level in cycles, providing a feeling of fresh air.

Pairing between remote control and receiver

1. Press the power button for 5-30 seconds and then you will hear a beep, which means that the pairing has been completed successfully and you can use the remote control normally.
2. If you notice that the transmitter does not control the receiver, check that the batteries are inserted correctly and that they are not dead.
3. This may also be due to the proximity of similar products that also operate with a remote control, which, if they use the same frequency, could cause interference.
4. If the batteries in the remote control are dead, replace them so that you can continue to use it normally.
5. Remove the batteries from the remote control if you are not going to use it for a long period of time.
6. Make sure that the earth wire is properly connected.
7. When positioning the fan, make sure that no wires are pinched. If this happens, a short-circuit may occur.

Reminder

ENGLISH

• The receiver must be correctly installed in the fan mounting bracket.
• Remove the batteries from the remote control if you are not going to use it for a long period of time.
• The isolation switch must be switched on.
• If the power is cut off (e.g. due to a blackout) the light will go out. When the power is restored, the light will switch on again.

Receiver protection functions

• The DC motor has a built-in safety feature against blade or motor obstruction during operation.
• During operation: if something obstructs the fan blades or motor, the motor will keep trying to run and then stop operation after about 30 seconds of interruption. Remove obstructions and restart the motor.
• To restart it: switch the fan off from the remote control and then switch it on again.
• The device will limit the maximum current output from the receiver/drive if the fan load has increased abnormally.

Tips

1. If your fan runs automatically when you switch it on for the first time after installation, it has memorised the previous factory setting. Use the universal mode or the learning code matching mode, and the fan will be ready for operation.
2. If the fan or light does not work, reset the fan. To do this, turn it off for at least 5 seconds and then turn it on again. Then, reset the learning code matching mode setting.
3. It is not possible to control more than one fan in the same room if they share the same power supply.
   If you want to separately control more than one fan in the same room, you must use separate power supplies.
4. When the fan is switched on and starts running in either direction (clockwise or counterclockwise), it will stop and change direction several times.
   This is normal. The fan will take some time to perform the selected function and to start up regularly.

4. CLEANING AND MAINTENANCE

1. Clean your fan periodically.
2. To clean, only use a soft brush or lint-free cloth to avoid scratching the finish.
3. Abrasive cleaning agents are not necessary and should be avoided in order not to damage the finish.

Warning. Do not use solvents to clean the fan. Doing so may result in electric shock.

RECOMMENDATION: periodically check that the blades are securely fastened to the motor with the screws.

5. TROUBLESHOOTING

Note that not all ceiling fans are the same (not even those that are the same model), some move more than others.

The fact that the fan moves a couple of centimetres does not indicate that it will fall over.

Even if all blades are ballasted and grouped by weight, it is impossible to completely avoid wobble. This is not a problem. Ceiling fans tend to move during operation.

To reduce wobble, try the following:

• Check that all of the blade mounting screws are tightened and secure.
• Fan wobble may be caused by the unevenness of the fan blades. To check the blade level, measure the distance from each blade tip to the ceiling.

Note: if measurements are irregular: Be sure the blade mount screws are not too tight or too loose, which may cause wobbling due to an unlevelled blade tip.

• A deformed blade can cause wobbling. Check by removing the blade and placing on a flat surface.
• Blade tracking may be checked simply by use of a household ruler. Place the ruler vertically against the ceiling and even with the outside leading edge of a blade. Note the distance of the edge of a blade compared to the others. Turn the blade slowly by hand to check the remaining blades.
• If a blade is not in alignment, the blade is either out of shape, warped or the blade screws are not evenly tightened or either loose.

6. TECHNICAL SPECIFICATIONS

Product reference: 08626

Product: EnergySilence Aero 3600 Invisible Metallic Style

Voltage: 220-240 V

Frequency: 50/60 Hz

Power: 25 W

*3 E27 (Max 36 W)

Description	Symbol	Value	Unit
Fan maximum flow	F	94.96	m^3/min
Fan power consumption	P	24.73	W
Service value	SV	3.84	(m^3/min)/W
Power consumption on standby mode	P_SB	0.49	W
Fan sound power level	L_WA	43.6	dB (A)
Maximum air speed	C	2.794	m/seg
Service value measurement standard	IEC 60789:2019
Contact details to obtain more information	Cecotec Innovaciones SL.Av. Reyes Católicos n°60, 46910, Alfajar (Valencia, Spain)

The power consumption in standby mode is 0.49 W using the guidelines of EN 50564:2011 and the European regulations 1275/2008/EC and 801/2013/EC. For this purpose, the device is connected to the mains without performing any function, waiting for the standby mode to be activated.

Technical specifications may change without prior notification to improve product quality.

Made in China | Designed in Spain

7. DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC APPLIANCES

This symbol indicates that, according to the applicable regulations, the product and/or batteries must be disposed of separately from household waste. When this product reaches the end of its shelf life, you should dispose of the cells/batteries/accumulators and take them to a collection point designated by the local authorities.

Consumers must contact their local authorities or retailer for information concerning the correct disposal of old appliances and/or their batteries.

Compliance with the above guidelines will help protecting the environment.

8. TECHNICAL SUPPORT AND WARRANTY

Cecotec shall be liable to the end user or consumer for any lack of conformity that exists at the time of delivery of the product under the terms, conditions, and deadlines established by the applicable regulations.

It is recommended that repairs be carried out by qualified personnel.

If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact the official Cecotec Technical Support Service at [phone].

9. COPYRIGHT

The intellectual property rights over the texts in this manual belong to CECOTEC INNOVACIONES, S.L. All rights reserved. The contents of this publication may not, in whole or in part, be reproduced, stored in a retrieval system, transmitted, or distributed by any means (electronic, mechanical, photocopying, recording or similar) without the prior authorization of CECOTEC INNOVACIONES, S.L.

1. PIÈCES ET COMPOSANTS

Image 1

3. HET APPARAAT MONTEREN

Houten plafond:

5. PROBLEEMOPLOSSING

Fig./Img./Abb./Afb./Rys. 4

Fig./Img./Abb./Afb./ Rys. 5

Fig./Img./Abb./Afb./Rys. 6

Fig./Img./Abb./Afb./ Rys. 7

Fig./Img./Abb./Afb./Rys. 8

Fig./Img./Abb./Afb./Rys. 9

Fig./Img./Abb./Afb./Rys.10

Fig./Img./Abb./Afb./Rys. 11

Fig./Img./Abb./Afb./Rys. 12

Fig./Img./Abb./Afb./Rys. 13

Fig./Img./Abb./Afb./Rys. 14

www.cecotec.es