EWE451KB-DWG2 - Water heater ELECTROLUX - Free user manual and instructions
Find the device manual for free EWE451KB-DWG2 ELECTROLUX in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Water Heater |
| Brand | Electrolux |
| Model | EWE451KB-DWG2 |
| Capacity | 50 Liters |
| Power Consumption | 2000 W |
| Voltage | 220-240 V |
| Energy Source | Electric |
| Temperature Range | 30°C to 75°C |
| Dimensions (H x W x D) | 450 x 350 x 350 mm |
| Weight | 15 kg |
| Tank Material | Stainless Steel |
| Safety Features | Overheat Protection, Pressure Relief Valve |
| Installation Type | Wall-Mounted Vertical |
| Control Type | Mechanical Thermostat |
| Warranty | 2 Years |
Frequently Asked Questions - EWE451KB-DWG2 ELECTROLUX
How do I install the water heater?
Ensure the wall is sturdy and mount the heater vertically. Connect to cold water inlet and hot water outlet using appropriate fittings. Connect to electrical supply (220-240 V) and install a pressure relief valve as per local codes. Fill the tank before switching on.
How can I adjust the water temperature?
Locate the thermostat dial on the front of the heater. Turn it to your desired temperature, typically between 30°C and 75°C. Wait for the heater to reach the set temperature.
What should I do if there is no hot water?
Check if the power supply is on and the circuit breaker hasn't tripped. Ensure the thermostat is set correctly. If the heating element is faulty, it may need replacement. Also check for airlocks in the system.
How do I drain the water heater?
Turn off the power supply and close the cold water inlet valve. Connect a hose to the drain valve at the bottom. Open the drain valve and a hot water tap to allow air in. Drain completely for maintenance or winterization.
Why is the pressure relief valve dripping?
This is normal if the water pressure is too high or the thermostat is set too high. Install a pressure reducing valve if needed. If dripping continues, the relief valve may be faulty and require replacement.
How do I clean the water heater?
Drain the tank as described. Use a descaling solution for mineral deposits. Flush thoroughly with fresh water. Clean the exterior with a damp cloth. Do not use abrasive cleaners.
What are some energy-saving tips?
Set the thermostat to 50-55°C to reduce heat loss. Insulate the hot water pipes. Use low-flow fixtures. Schedule heating during off-peak hours if possible.
Are there any error codes?
This model uses a mechanical thermostat and does not display error codes. If the heater is not working, check power and thermostat settings. Continuous issues may indicate a heating element failure.
Can this water heater be used with a solar system?
Yes, it can be used as a booster for solar pre-heated water. Connect the solar outlet to the cold water inlet. Ensure the thermostat is set to a lower temperature to avoid overheating.
How often should I replace the anode rod?
The anode rod protects the tank from corrosion. Inspect it every 1-2 years and replace if more than 50% corroded. Use a 1-inch socket to remove and install a new rod.
User questions about EWE451KB-DWG2 ELECTROLUX
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Water heater in PDF format for free! Find your manual EWE451KB-DWG2 - ELECTROLUX and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. EWE451KB-DWG2 by ELECTROLUX.
USER MANUAL EWE451KB-DWG2 ELECTROLUX
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : ELECTROLUX
Model : EWE451KB-DWG2
Category : Water heater