CC4062MBT - Receiver Bogen - Free user manual and instructions
Find the device manual for free CC4062MBT Bogen in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Commercial Paging Receiver / Amplifier |
| Brand | Bogen |
| Model | CC4062MBT |
| Dimensions (W x H x D) | 17.0 x 3.5 x 12.0 inches (432 x 89 x 305 mm) |
| Weight | 12.5 lbs (5.7 kg) |
| Power Supply | 120 VAC, 60 Hz, 1.5 A |
| Power Output | 60 Watts RMS into 25V or 70V distributed lines |
| Inputs | 1 Mic/Line input (3-pin XLR), 1 Aux input (RCA), 1 Bluetooth input |
| Outputs | 1 Amplified output (screw terminals), 1 Line output (RCA) |
| Frequency Response | 80 Hz - 15 kHz (+/- 3 dB) |
| Impedance | 25V/70V distributed line |
| Bluetooth Version | 5.0 |
| Mounting | Rack-mountable (2U), or shelf placement |
| Cooling | Convection cooled; internal fan |
| Controls | Volume, Bass, Treble, Input selector, Power switch |
| Indicators | Power LED, Signal LED, Protect LED |
| Operating Temperature | 32°F to 104°F (0°C to 40°C) |
| Safety Certifications | UL 60065, CSA, FCC Part 15 |
| Cleaning Instructions | Disconnect power; use dry cloth; avoid liquids |
| Spare Parts & Repairability | Available through Bogen authorized service centers; user-replaceable fuse |
| Warranty | 2 years limited |
Frequently Asked Questions - CC4062MBT Bogen
How do I pair a Bluetooth device with the CC4062MBT?
Press and hold the Bluetooth button on the front panel for 3 seconds until the LED starts flashing. Enable Bluetooth on your device and select 'Bogen CC4062MBT' from the list. The LED will become solid when connected.
What type of speakers can I use with this receiver?
The CC4062MBT is designed for 25V or 70V distributed speaker systems. Use constant-voltage speakers with appropriate wattage taps. Do not use low-impedance speakers (4-8 ohms) directly.
How do I reset the receiver to factory defaults?
With the unit powered on, press and hold the Volume knob for 10 seconds until all LEDs flash. Release the knob. The unit will reboot with default settings.
The receiver has no audio output. What should I check?
First, verify the power LED is on. Check the input source selection and volume level. Ensure the Protect LED is off. If the Protect LED is on, there may be a short circuit in the speaker wiring. Disconnect speakers and try again.
Can I use the CC4062MBT in a 19-inch rack?
Yes, the unit is 2U rack-mountable. Use the included rack ears and four screws to mount it securely in a standard 19-inch rack.
What is the maximum distance for Bluetooth connection?
The Bluetooth range is approximately 30 feet (10 meters) in open space. Walls and obstacles may reduce the range.
How do I clean the CC4062MBT?
Disconnect the power cord. Use a soft, dry cloth to wipe the exterior. Do not use any liquids, sprays, or abrasive cleaners.
The receiver overheats and shuts off. What can I do?
Ensure adequate ventilation around the unit. Do not block the fan vents. If the unit is in a rack, leave at least 1U space above and below. Reduce the ambient temperature if possible.
Can I connect a microphone directly to the CC4062MBT?
Yes, the Mic/Line input accepts a balanced XLR microphone. For dynamic microphones, use the mic setting (if available). For condenser microphones, phantom power is not provided; use a preamp.
How do I replace the internal fuse?
Disconnect the power cord. Locate the fuse holder on the rear panel near the AC inlet. Use a screwdriver to open the holder and replace the fuse with the same type and rating (e.g., 2A, 250V). Never use a higher rating.
User questions about CC4062MBT Bogen
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual CC4062MBT - Bogen and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. CC4062MBT by Bogen.