THOR TPS-BT1 - Uncategorized Hifonics - Free user manual and instructions
Find the device manual for free THOR TPS-BT1 Hifonics in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Bluetooth Car Audio Receiver / Amplifier |
| Brand | Hifonics |
| Model | THOR TPS-BT1 |
| Dimensions (W x H x D) | 6.0 x 2.0 x 4.0 inches |
| Weight | 1.5 lbs (0.68 kg) |
| Power Supply | 12V DC (vehicle battery) |
| Bluetooth Version | 5.0 |
| Bluetooth Range | Up to 30 ft (10 m) |
| Audio Inputs | RCA, Bluetooth |
| Audio Outputs | Speaker terminals, RCA pre-outs |
| Maximum Power Output | 1000W peak (2 ohms) |
| Frequency Response | 20Hz – 20kHz |
| Signal-to-Noise Ratio | > 90 dB |
| Total Harmonic Distortion | < 0.1% |
| Protection Circuits | Overload, thermal, short circuit |
| Controls | Volume, bass boost, input select |
| LED Indicator | Power and pairing status |
| Mounting Type | In-dash or under-seat |
| Operating Temperature | -20°C to 60°C |
| Cleaning Instructions | Wipe with dry cloth; avoid liquids |
| Safety Warnings | Disconnect battery before installation; use proper fuse |
| Spare Parts Availability | Contact Hifonics support for replacement parts |
Frequently Asked Questions - THOR TPS-BT1 Hifonics
How do I pair my phone with the THOR TPS-BT1?
Activate Bluetooth on your phone, then press the pairing button on the device (or set it to discoverable). Select THOR TPS-BT1 from the list. Enter PIN 0000 if prompted.
What power source is required for the THOR TPS-BT1?
This device operates on a 12V DC power supply, typically from a car battery. Ensure proper fuse protection (e.g., 15A) during installation.
Can I use this amplifier with aftermarket speakers?
Yes, the THOR TPS-BT1 is compatible with most car speakers. The speaker terminals accept up to 12 gauge wire. Match impedance to avoid distortion.
How do I adjust the bass boost?
Use the Bass Boost knob (typically labeled 0-12 dB) on the unit. Turn clockwise to increase bass. Avoid excessive boost to prevent speaker damage.
What does the LED indicator mean?
Solid blue means powered on and paired. Flashing blue indicates pairing mode. Red may indicate a protection fault (overload or thermal). Check connections.
Is the THOR TPS-BT1 waterproof?
No, this device is not waterproof. It is designed for dry interior installation in vehicles. Avoid exposure to moisture.
How do I clean the device?
Use a soft, dry cloth to wipe the exterior. Do not use chemical cleaners or water, as they may damage electronics.
What is the maximum power output?
The peak power is 1000 watts at 2 ohms. Continuous RMS power is lower (check spec sheet). Use speakers rated accordingly.
Can I connect multiple speakers?
Yes, you can wire multiple speakers in parallel or series, ensuring total impedance does not fall below 2 ohms. Proper speaker wiring is essential.
Where can I find the user manual?
The user manual is available for free download on notice-facile.com in PDF format. Use the download button on this page.
User questions about THOR TPS-BT1 Hifonics
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual THOR TPS-BT1 - Hifonics and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. THOR TPS-BT1 by Hifonics.
USER MANUAL THOR TPS-BT1 Hifonics
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Hifonics
Model : THOR TPS-BT1
Category : Uncategorized