Bolero Flux Tlm 603500 A - Range hood CECOTEC - Free user manual and instructions

Product type	Cooker hood
Brand	Cecotec
Model	Bolero Flux Tlm 603500 A
Width	60 cm
Depth	50 cm
Height	15 cm (built-in)
Net weight	Approximately 10 kg
Power supply	220-240 V ~ 50 Hz
Suction power	Up to 650 m³/h
Number of speeds	3 speeds + intensive
Lighting	Integrated LED
Controls	Touch controls
Filter type	Washable aluminum grease filter and activated charcoal filter (optional)
Evacuation mode	External evacuation or recirculation
Noise level	Approximately 55 dB (minimum speed)
Automatic shut-off function	Yes, integrated timer
Maintenance and cleaning	Grease filter dishwasher safe; charcoal filter to be replaced every 3-6 months
Safety	Automatic shut-off in case of overheating
Spare parts available	Filters, LED bulbs, remote control (depending on model)
Repairability	Repairability index not communicated

Frequently Asked Questions - Bolero Flux Tlm 603500 A CECOTEC

How to install the Cecotec Bolero Flux Tlm 603500 A hood?

Installation must be carried out by a qualified professional. Ensure the hood is securely attached to the wall or cabinet, at a height of 65-75 cm above the cooking surface. Follow the manual instructions for electrical connection and evacuation.

How to clean the hood filters?

The aluminum grease filters can be washed in the dishwasher or by hand with warm soapy water. Let them dry completely before reinstalling. The charcoal filters must be replaced every 3 to 6 months.

Why is my hood making noise?

Abnormal noise may come from a clogged filter, improper installation, or a foreign object in the motor. Clean the filters and ensure the hood is properly fixed. If the noise persists, contact customer service.

What are the exact dimensions of the hood?

The Cecotec Bolero Flux Tlm 603500 A hood has a width of 60 cm, a depth of 50 cm, and a height of approximately 15 cm. Check the available space before installation.

Can the hood be used in recirculation mode?

Yes, the hood can operate in recirculation mode with an activated charcoal filter (sold separately). In this case, the air is filtered and then returned to the room.

How to set the hood timer?

The hood has an integrated timer. Press the timer button to activate automatic shut-off after 10 minutes (or depending on the model). Refer to the manual for details.

What to do if the hood no longer turns on?

First check that the appliance is properly plugged in and that the circuit breaker has not tripped. If the LED lighting does not work, it may be defective and require replacement by a professional.

How to replace the LED bulb of the hood?

The LED lighting is integrated and may require a technician for replacement. Do not attempt to do it yourself to avoid electrical risk.

What is the suction power of this hood?

The hood offers a maximum suction power of approximately 650 m³/h, with 3 adjustable speeds and an intensive function for strong odors.

Where to find spare parts for the Cecotec hood?

Spare parts such as filters and bulbs are available on the official Cecotec website or from authorized dealers. Check compatibility with your model.

USER MANUAL Bolero Flux Tlm 603500 A CECOTEC

Safety instructions 8

1. Parts and components 51

2. Before use 51

3. Installation 51

4. Operation 53

5. Cleaning and maintenance 53

6. Troubleshooting 55

7. Technical specifications 56

8. Disposal of old electrical and electronic appliances 59

9. Technical support and warranty 59

10. Copyright 60

SOMMARIE

Read these instructions thoroughly before using the device. Keep this instruction manual for future reference or new users.

• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children must not play with the appliance. Cleaning and user maintenance should not be carried out by unsupervised children.
• This device is designed for domestic use only and is not intended for bars, restaurants, farmhouses, hotels, motels, and offices.
• If the power cable is damaged, it must be replaced by the official Cecotec Technical Support Service or similar qualified personnel to avoid risks.
• You must allow the appliance to be disconnected from the power supply after installation.
• There must be adequate ventilation of the room when the kitchen hood is used at the same time as gas or other fuel burning appliances.
• There is a risk of fire if cleaning is not carried out according to the instructions.
• Do not flambé under the kitchen hood.
• CAUTION: accessible parts can become hot when used with cooking appliances.
• Air must not be discharged into a duct that is used to exhaust fumes from appliances burning gas or other fuels.
• The minimum distance between the support surface of the cooking containers on the worktop and the lowest part of

the kitchen hood, when it is located above a gas appliance, must be at least 65 cm. If the installation instructions for the gas appliance specify a greater distance, this must be taken into account. The distance of 65 cm can be reduced for:

I. Non-combustible parts of kitchen hoods.

II. Parts operating at safety extra-low voltage (provided that these parts do not give access to live parts if they are deformed).

The air discharge regulations must be complied with.

The kitchen hood is intended for installation only over a hob with four cooking zones.

Things you should never do:

I. Do not attempt to use the kitchen hood without the mesh filter or if the filter is excessively dirty or greasy!

II. Do not install the kitchen hood above a cooker with a high-level grill.

III. Do not leave pans unattended during use because overheated fats or oils may catch fire.

- Accumulation of grease in the kitchen hood can cause a fire hazard. Clean the appliance according to the instructions in this manual.

- Exercise extreme caution when cleaning the appliance. Risk of burns and/or cuts. We recommend the use of gloves.

- Never leave open flames under the kitchen hood.

- If the kitchen hood is damaged, do not attempt to use it.

- When the kitchen hood and other non-electrically powered appliances are in simultaneous operation, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar).

- Important! Always disconnect the power supply during installation and maintenance.

- The kitchen hood must be installed in accordance with the installation instructions and in compliance with all measurements.

• All installation work must be carried out by a competent person or a qualified electrician.
• Dispose of the packaging material carefully. Children are vulnerable to it.
• Pay attention to sharp edges inside the kitchen hood, especially during installation and cleaning.
• Make sure that the duct does not have bends sharper than 90 degrees, as this will reduce the efficiency of the kitchen hood.
• Warning: failure to install the screws or fastening device in accordance with these instructions may result in electrical hazards
• Warning: before accessing the electrical terminals, all power supply circuits must be disconnected.
• There must be adequate ventilation of the room when the kitchen hood is used at the same time as gas or other fuel burning appliances.
• Caution: the appliance and its accessible parts may become hot during operation. Be careful not to touch any accessible parts. Children under 8 years old must stay away, unless they are supervised.
• Local air discharge regulations must be complied with.
• For safety reasons, only use the supplied fixing or mounting screws (if applicable, depending on the model) or screws of the same size as those recommended in this instruction manual.
• You should not use a steam cleaner.
• NEVER try to put out the fire with water. Instead, turn off the appliance and smother the flame with, e.g., a fireproof lid or blanket.

• Never use extension cables, multiple socket connections or external timer connection elements.

• If the power cord is damaged, it must be replaced by the official Cecotec Technical Support Service or by similarly qualified technicians to prevent hazards.

• The appliance must not be operated if the power supply cable is damaged or cut.
• If the appliance stops working or malfunctions abnormally, disconnect it from the mains and contact the official Cecotec Technical Support Service.
• Cecotec disclaims all liability for any damage or injury caused as a result of failure to follow the installation and/or operating instructions contained in this instruction manual.

INSTRUCTIONS DE SÉCURITÉ

the graphics in this manual are schematic representations and may not exactly match the device.

2. BEFORE USE

• This appliance is packaged in a way as to protect it during transport. Take the device out of its box and remove all packaging materials. You can keep the original box and other packaging elements in a safe place. This will help you prevent damage to the device when transporting it in the future. In case the original packaging is disposed of, make sure all packaging materials are recycled accordingly.
• Make sure all parts and components are included and in good conditions. If there is any piece missing or in bad conditions, contact the official Cecotec Technical Support Service immediately.

Box content

• Kitchen hood
• Assembly kit (depending on model)
• Instruction manual

3. INSTALLATION

The dimensions of the following kitchen hoods are shown in Figure 3.

02859_Bolero Flux TLM 603500 White A

02860_Bolero Flux TLM 603500 Black A

02861_ Bolero Flux TLM 603500 Inox A

The dimensions of the following kitchen hoods are shown in Figure 4. 02862_ Bolero Flux TLM 606500 Inox A

• Before installing the kitchen hood, make sure that the area is clean to prevent it from sucking in dust or dirt.
• Please note that the kitchen hood must not share the same ventilation duct with other appliances that use gas or other fuses.
• To facilitate air outlet, the ventilation duct should have a curvature of ≥ 120° and should be connected to the outside wall, parallel to or above the starting point.
• After installation, ensure that the kitchen hood is level to prevent grease build-up on the end (Fig. 5).

Steps to install the kitchen hood:

1 The kitchen hood should be placed at a distance of 65-75 cm above the cooking surface for best effect (Fig 6).
2 Using a drill, drill 4 ∅ 5 mm holes and a ∅ 170 mm hole at the bottom of the wall unit as shown in Figure 7.

Fig. 7 key:

A. Hole 4 - ø5 mm
B. Hole φ 170 mm
C. Washer (gasket) 4 - ø12
D. Screw 4 - M4x30
E. Cabinet
F. Air outlet
G. Washer 4 -M4

3 Remove the mesh filter. Insert the plastic plugs into the holes and secure the kitchen hood to the cabinet using the screws. Make sure it is centred with the worktop and replace the filter.

4 Once the kitchen hood has been hung up, you can install the flexible chimney connection pipe (∅150 mm) at the outlet of the ventilation duct, located at the top of the kitchen hood (Fig. 8). If necessary, connect the other end of the flexible connection pipe to the wall chimney.

5 Connect the connection cable to the mains socket.

Black cable (or brown, depending on models) > Phase

Blue cable > neutral

Yellow-Green cable > ground

You must connect the phase and neutral cables to a 220-240 V\~/ 50 Hz power cable.

The kitchen hood must be connected to an earthed installation.

4. OPERATION

Switches

1. To switch on the kitchen hood, set the switch to position "I" or "II".
2. In the low-power position (I), the motor will operate at low speed.
3. In the high-power position (II), the motor will operate at high speed.
4. To stop the operation of the kitchen hood, turn the switch to the "0" position.
5. To switch on the light, put the switch to "I" position.
6. To switch off the light, put the switch to "0" position.

NOTE: the hoods are equipped with an overheating protection system that acts to prevent possible incidents when the motor temperature exceeds the operating limit value.

5. CLEANING AND MAINTENANCE

Always switch off the power supply before cleaning or performing any maintenance work on the kitchen hood. Please note that the cleaning and maintenance frequency depends on the use frequency and intensity.

1. To prevent the outer surface of the kitchen hood from deteriorating over time, it is recommended that it be cleaned with hot water and a non-corrosive detergent every two months.
2. Do not use abrasive detergents. Otherwise, the surface of the kitchen hood may be damaged.
3. Keep the motor and other parts away from water, as water may damage the appliance.

Cleaning the filters

Do not use corrosive detergents to clean grease from the mesh filters. Regular cleaning of the filters will prolong the life of the appliance and keep it in good working order. Follow the instructions below:

• Cleaning method 1: immerse the mesh filters in hot water (40–50 °C), add neutral detergent and let them soak for 2 to 3 minutes. Protect yourself with gloves and clean the filters with a soft brush or scouring pad. Do not apply too much force, as filters are very delicate and can be easily damaged.
• Cleaning method 2: if you wish, you can also wash the filters in the dishwasher at a temperature of approx. 60 °C.

- To remove the filter, press on the tabs as shown in Figure 9 and pull it out.

Carbon filter

This type of filter has activated carbon and purifies air and absorbs cooking odours. The activated carbon becomes saturated after a period of time, which will reduce the adsorption capacity of the filter. The carbon filter cannot be washed nor cleaned in any way. When its service life comes to an end you must replace it with a new one.

• It is recommended to check the condition of carbon filters regularly, at least two or three times a year. Its replacement will depend on how the kitchen hood is used, as well as the daily operating time.
• In case of very frequent frying, shorten the time interval for checking and/or replacing the carbon filters.

Installing the carbon filters

1. Remove the protective metal filters.
2. The carbon filters are located on both sides of the motor. Insert and turn the filters, until they are firmly in place.
3. To replace the carbon filter, proceed in reverse order.
4. The carbon filter must not be exposed to heat.

Fig. 2 10:

A: Closed
B: Opened
C: Opened
D: Closed

Carbon filter diameter:

Article No 02859/02860/02861 > 132 mm

Article No 02862 > 176 mm

Replacing the light bulb/lamp

Please note:

• The light bulb must be replaced by the official Cecotec Technical Support Service or similarly qualified technicians.
• Always disconnect the power supply before performing any operation on the appliance. When handling the bulb, make sure that it has cooled down completely before any direct contact with your hands.
• When handling the bulbs, hold them with a cloth or gloves to prevent sweat from coming into contact with the bulb, as this may reduce the bulb life.

Note:

• Before changing the light bulb, make sure that the appliance is switched off and unplugged.

• Protect yourself from danger when changing the light bulb, e.g., by wearing gloves.

• TROUBLESHOOTING

Fault	Cause	Solution
The indicator light is on, but the motor does not work	The kitchen hood is obstructed	Remove what is obstructing the hood
	The condenser is damaged	Please contact the official Cecotec Technical Support Service to replace the condenser.
	Motor is jammed or bearing damaged	Please contact the official Cecotec Technical Support Service to replace the motor.
	Motor is burnt or gives off a bad smell	Please contact the official Cecotec Technical Support Service to replace the motor.
Neither the light bulb nor the motor work	In addition to the above, check the following:
	The light bulb has blown	Please contact the official Cecotec Technical Support Service to replace the light bulb.
	Power cable is loose	Please contact the official Cecotec Technical Support Service to connect the cables according to the wiring diagram.
Grease falls out of the aluminium filters	The filters are very dirty	Clean or replace the aluminium filters immediately
The kitchen hood vibrates	The fan is damaged, causing the kitchen hood to vibrate when extracting air.	Please contact the official Cecotec Technical Support Service to replace the fan.
	The engine is not securely fastened	Fix the engine correctly
	The kitchen hood is not securely fastened	Fix the kitchen hood correctly
The kitchen hood is not sufficiently extracting	The distance between the kitchen hood and the cooking surface is too large.	Readjust the distance
	There is too much ventilation in the room due to open doors or windows	Relocate and reinstall the kitchen hood
The kitchen hood is tilted	Fastening screws are not tightened properly	Reposition the kitchen hood horizontally and tighten the screws.
	Plastic plugs are not tightened properly	Reposition the kitchen hood horizontally and tighten the plugs.

If none of these situations match your problem, do not attempt to disassemble, or repair the appliance by yourself. Repairs carried out by unqualified persons may result in injury or serious malfunctions. Contact the official Cecotec Technical Support Service. The repair must be carried out by an authorised technician, and you must use only original spare parts.

Unauthorised self-maintenance or maintenance will affect the safe use of the product and the application of the warranty policy.

NOTE:

Any electrical repairs to this appliance must conform to local and/or state laws. Please contact the official Cecotec Technical Support Service in case of doubt and before carrying out any of the above operations. Always disconnect the device from the power supply when opening it.

7. TECHNICAL SPECIFICATIONS

All technical information is available on the public website of the European Product Register for Energy Labelling (EPREL):

eprel.ec.europa.eu/screen/home

Regulation (EU) 65/2014

EU Directive 2010/30/EU

Product reference: 02859 / 02860 / 02861

Product name: Bolero Flux TLM 603500 White A / Bolero Flux TLM 603500 Black A / Bolero Flux TLM 903500 Inox A

Rated voltage: 220-240 V

Rated frequency: 50 Hz

Total power: 71.5 W

Motor: 70 W

Light bulb: 1 x 1.5 W

650 m³/h air flow

Bulb type: rectangular LED light

Bulb dimensions: (120 x 33) mm

ILCOS Code D: DBL-1.5-S-120/33

	Symbol	Value	Unit
Model reference		02859 / 02860/02861
Annual energy consumption	AEC hood	22.3	kWh/a
Time increment factor	f	1.2
Fluid dynamic efficiency	FDE hood	21.7
Energy Efficiency Index (EEIW)	EEI hood	52.5
Measured airflow at maximum efficiency point	QBEP	188.2	m3/h
Air pressure measured at maximum efficiency point	PBEP	197	Pa
Maximum airflow	Qmax	372.5	m3/h
Electrical input power measured at maximum efficiency point	WBEP	47.5	W
Nominal power of the lighting system	WL	2	W
Measured illumination of the illumination system on the cooking surface	Emed	79	lux
Standby power consumption	PS	N/A	W
Power consumption in off mode	Po	0	W
Noise level (Highest setting)	LWA	65	dB
Noise level (Lowest setting)	LWA	60	dB

This appliance features a light source with an energy efficiency grade A.

The appliance power consumption when off is 0 W, following the guidelines of EN 50564:2011 and the European regulations 1275/2008/EC and 801/2013/EC. The appliance doesn't perform any function when connected to the mains. The switch/controller of the appliance was set to the Off position.

Product reference: 02862

Product name: Bolero Flux TLM 606500 Inox A

Rated voltage: 220-240 V

Rated frequency: 50 Hz

Total power: 166,5 W

Motor: 165 W

Light bulb: 1 x 1.5 W

650 m³/h air flow

Bulb type: rectangular LED light

Bulb dimensions: (120 x 33) mm

ILCOS Code D: DBL-1.5-S-120/33

	Symbol	Value	Unit
Model reference		02862
Annual energy consumption	AEC hood	36.3	kWh/a
Time increment factor	f	0.9
Fluid dynamic efficiency	FDE hood	30.1
Energy Efficiency Index (EEIW)	EEI hood	48.3
Measured airflow at maximum efficiency point	QBEP	295.7	m3/h
Air pressure measured at maximum efficiency point	PBEP	393	Pa
Maximum airflow	Qmax	620.6	m3/h
Electrical input power measured at maximum efficiency point	WBEP	107.2	W
Nominal power of the lighting system	WL	1.5	W
Measured illumination of the illumination system on the cooking surface	Emed	72	lux

Standby power consumption	Ps	N/A	W
Power consumption in off mode	Po	0	W
Noise level (Highest setting)	LWA	68	dB
Noise level (Lowest setting)	LWA	62	dB

This appliance features a light source with an energy efficiency grade A.

The appliance power consumption when off is 0 W, following the guidelines of EN 50564:2011 and the European regulations 1275/2008/EC and 801/2013/EC. The appliance doesn't perform any function when connected to the mains. The switch/controller of the appliance was set to the Off position.

Technical specifications may change without prior notification to improve product quality. Made in China | Designed in Spain

8. DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC APPLIANCES

This symbol indicates that, according to the applicable regulations, the product and/or batteries must be disposed of separately from household waste. When this product reaches the end of its shelf life, you should dispose of the cells/batteries/accumulators and take them to a collection point designated by the local authorities.

Consumers must contact their local authorities or retailer for information concerning the correct disposal of old appliances and/or their batteries.

Compliance with the above guidelines will help protecting the environment.

9. TECHNICAL SUPPORT AND WARRANTY

Cecotec shall be liable to the end user or consumer for any lack of conformity that exists at the time of delivery of the product under the terms, conditions, and deadlines established by the applicable regulations.

It is recommended that repairs be carried out by qualified personnel.

If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact the official Cecotec Technical Support Service at [phone].

10. COPYRIGHT

The intellectual property rights over the texts in this manual belong to CECOTEC INNOVACIONES, S.L. All rights reserved. The contents of this publication may not, in whole or in part, be reproduced, stored in a retrieval system, transmitted, or distributed by any means (electronic, mechanical, photocopying, recording or similar) without the prior authorization of CECOTEC INNOVACIONES, S.L.

1. PIÈCES ET COMPOSANTS

Directive 2010/30/UE

Instalar o exaustor:

Fig./Img./Abb./Afb./Rys./Obr. 7

Fig./Img./Abb./Afb./Rys./Obr. 8

Fig./Img./Abb./Afb./Rys./Obr. 9

Fig./Img./Abb./Afb./ Rys./Obr. 10

www.cecotec.es