TP555 - Drill BLACK & DECKER - Free user manual and instructions
Find the device manual for free TP555 BLACK & DECKER in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Cordless Drill Driver |
| Brand | Black & Decker |
| Model | TP555 |
| Voltage | 18 V |
| Battery Type | Lithium-Ion |
| Battery Capacity | 1.5 Ah |
| No-Load Speed | 0-750 RPM |
| Max Torque | 30 Nm |
| Chuck Type | Keyless, 1-10 mm |
| Number of Gears | 2 |
| Clutch Positions | 20 |
| Rotation Direction | Reversible |
| Weight | 1.5 kg |
| Dimensions (LxWxH) | 250 x 80 x 200 mm |
| Power Source | Rechargeable Battery |
| LED Light | Yes |
| Grip | Ergonomic with rubber overmold |
| Safety Features | Lock-off switch, motor brake |
| Maintenance | Clean with dry cloth; periodic lubrication |
| Spare Parts | Battery, charger, chuck, carbon brushes |
Frequently Asked Questions - TP555 BLACK & DECKER
How do I change the chuck on the Black & Decker TP555?
To change the chuck, first remove the battery. Use a hex key (Allen wrench) to loosen the screw inside the chuck. Turn the chuck counterclockwise to unscrew it. Install the new chuck by hand-tightening and then secure the screw.
How do I charge the battery for the TP555?
Place the battery into the charger until it clicks. The charger LED will indicate charging status. A full charge typically takes 1-2 hours. Always use the included charger.
What type of battery does the TP555 use?
The TP555 uses an 18V lithium-ion battery. Only use batteries and chargers recommended by Black & Decker.
How do I adjust the speed or torque on the TP555?
The drill has a variable speed trigger. Lighter pressure gives slower speed, full pressure gives maximum speed. For torque, rotate the clutch ring to one of 20 positions for driving screws.
How do I reverse the direction of the drill?
Locate the forward/reverse switch above the trigger. Push it to the left for forward (clockwise) rotation, and to the right for reverse (counterclockwise). Always wait for the chuck to stop before switching.
Can I use the TP555 for drilling into masonry?
The TP555 is primarily designed for wood, metal, and plastic. For masonry, a hammer drill is recommended. Using a masonry bit at low speed may work, but it is not ideal.
How do I clean and maintain the TP555?
Clean the drill with a dry cloth; avoid water or solvents. Periodically lubricate the chuck and motor bearings. Keep air vents free of dust.
What safety precautions should I take when using the TP555?
Always wear safety glasses and gloves. Ensure the area is well-lit. Keep hands away from the spinning chuck. Do not apply excessive pressure. Disconnect the battery when not in use.
How do I replace the carbon brushes?
Carbon brushes are located on both sides of the motor. Unscrew the brush caps, remove worn brushes, and insert new ones. Tighten the caps. Ensure brushes are properly seated.
Why is my TP555 not starting?
Check that the battery is charged and properly inserted. Ensure the forward/reverse switch is not in the middle position. If the drill still doesn't start, the battery or motor may be faulty.
User questions about TP555 BLACK & DECKER
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Drill in PDF format for free! Find your manual TP555 - BLACK & DECKER and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. TP555 by BLACK & DECKER.
USER MANUAL TP555 BLACK & DECKER
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : BLACK & DECKER
Model : TP555
Category : Drill