1311-220 - Drill BLACK & DECKER - Free user manual and instructions
Find the device manual for free 1311-220 BLACK & DECKER in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Brand | Black & Decker |
| Model | 1311-220 |
| Product Type | Drill |
| Power Source | Corded Electric |
| Power Consumption | 600 W |
| No-Load Speed | 0-2800 RPM |
| Chuck Size | 13 mm (1/2 inch) |
| Chuck Type | Keyed |
| Drilling Capacity (Steel) | 13 mm |
| Drilling Capacity (Wood) | 25 mm |
| Weight | 1.5 kg |
| Dimensions (LxWxH) | 260 x 60 x 200 mm |
| Cable Length | 2 m |
| Safety Features | Double insulation, lock-on button |
| Maintenance | Keep ventilation slots clean; replace brushes when worn |
| Accessories Included | Depth stop, chuck key, side handle |
| Warranty | 2 years |
| Spare Parts Availability | Brushes, chuck, switch available from Black & Decker service centers |
| Repairability | User replaceable brushes; professional servicing recommended for other parts |
Frequently Asked Questions - 1311-220 BLACK & DECKER
How do I change the chuck on the Black & Decker 1311-220 drill?
To change the chuck, first unplug the drill. Insert a hex key (5 mm) into the chuck and tighten it. Strike the key sharply with a hammer to loosen the chuck. Unscrew the chuck by hand. Install the new chuck and tighten securely.
What is the recommended drill bit size for metal?
For steel, the maximum drill bit size is 13 mm. Use a center punch to start the hole and apply cutting oil for best results.
How do I replace the carbon brushes?
Unplug the drill. Remove the brush caps on the side with a screwdriver. Slide out the old brushes and replace with new ones (part number 123456). Ensure the brushes are fully seated before tightening the caps.
Can I use the drill for concrete?
This drill is not a hammer drill. For concrete, you can use a carbide-tipped masonry bit but it will be slow. Consider a hammer drill for better performance.
What is the speed range of this drill?
The drill has a variable speed trigger with 0-2800 RPM. Use lower speeds for driving screws and higher speeds for drilling.
Is the drill double insulated?
Yes, the Black & Decker 1311-220 is double insulated, meaning it does not require a grounded power outlet. It is safe for use in standard household outlets.
How do I use the depth stop?
Loosen the depth stop clamp, slide the rod to the desired depth, and tighten the clamp. The rod will limit how far the drill can penetrate.
Why is the drill running slowly?
Check the power supply and cord. If the drill is under load, it may slow. Excessive brush wear or a dirty commutator can also cause slow speed. Replace brushes if needed.
Can I use this drill for screwdriving?
Yes, with a screwdriver bit adapter. Use low speed and adjust the clutch (if available) to avoid stripping screws. This model does not have a clutch, so be careful with torque.
How do I clean the drill?
Unplug the drill. Wipe the exterior with a damp cloth. Do not use solvents. Clean ventilation slots with a soft brush. Avoid getting water inside.
User questions about 1311-220 BLACK & DECKER
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Drill in PDF format for free! Find your manual 1311-220 - BLACK & DECKER and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 1311-220 by BLACK & DECKER.
USER MANUAL 1311-220 BLACK & DECKER
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : BLACK & DECKER
Model : 1311-220
Category : Drill