Crestron

ZUMLINK-DT-QUATTRO-DLS-RLY - Motion detector Crestron - Free user manual and instructions

Find the device manual for free ZUMLINK-DT-QUATTRO-DLS-RLY Crestron in PDF.

📄 291 pages English EN ⬇ Download 💬 AI Question ❓ 10 questions ⚙️ Specs
Notice Crestron ZUMLINK-DT-QUATTRO-DLS-RLY - page 8
8 / 291
Pick your language and provide your email: we'll send you a specifically translated version.
Brand Crestron
Model ZUMLINK-DT-QUATTRO-DLS-RLY
Product Type Motion Detector with Ambient Light Sensor
Detection Technology Dual Technology (PIR and Ultrasonic)
Coverage Area Up to 1800 sq ft (360° ceiling mount)
Daylight Sensor Range 0–1500 lux
Outputs Form C Relay (SPDT), 0–10V Dimming
Communication Protocol Crestron infiNET EX®
Mounting Ceiling (optional wall bracket)
Dimensions Ø 4.5 in x 1.3 in (114 mm x 33 mm)
Weight 0.5 lb (227 g)
Power Supply Power over Ethernet (PoE) or Cresnet
Power Consumption 2.5 W (PoE PD)
Adjustable Settings Sensitivity, time delay, dimming setpoint
Operating Temperature 32°F to 104°F (0°C to 40°C)
Humidity 10%–90% (non-condensing)
Safety Certifications UL, CE, FCC Part 15
Maintenance Wipe with a dry, soft cloth; no solvents
Spare Parts / Repairability No user-serviceable parts; contact Crestron service

Frequently Asked Questions - ZUMLINK-DT-QUATTRO-DLS-RLY Crestron

How do I restore factory defaults on the Crestron ZUMLINK-DT-QUATTRO-DLS-RLY?
Press and hold the reset button for 10 seconds until the LED blinks green three times. All settings revert to factory defaults.
What is the maximum wire length for the relay and dimming outputs?
Relay output: 100 ft (30 m). Dimming output: 200 ft (61 m) using 18 AWG wire. For longer runs, use signal amplifiers.
Can the motion detector be used outdoors?
No, it is intended for indoor use only. Exposure to moisture or extreme temperatures may damage the sensor.
How do I adjust the sensitivity of the PIR sensor?
Use the Crestron Device Toolbox software or the infrared remote accessory. Sensitivity can be set from 1 (low) to 5 (high).
What type of power supply is required?
The detector can be powered via Power over Ethernet (802.3af) or a Crestron Cresnet power supply (24 V DC, 2.5 W).
The LED is flashing red; what does it mean?
A flashing red LED indicates a communication error. Check the network connection and ensure the device is properly addressed.
What is the recommended mounting height?
For ceiling mount, the optimal height is 8–12 ft (2.4–3.7 m). For wall mount, install 6–8 ft (1.8–2.4 m) above the floor.
Does the daylight sensor work with LED lighting?
Yes, the ambient light sensor is calibrated for a wide range of light sources, including LED, fluorescent, and incandescent.
Can I connect the detector to a 3rd party HVAC system?
The relay output can interface with any dry contact input. For digital communication, use the Crestron infiNET EX gateway.
How do I clean the sensor lens?
Use a microfiber cloth slightly dampened with water or a mild soap solution. Do not use abrasive cleaners or alcohol.

User questions about ZUMLINK-DT-QUATTRO-DLS-RLY Crestron

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

The email remains private: it is only used to notify you if someone responds to your question.

No questions yet. Be the first to ask one.

Download the instructions for your Motion detector in PDF format for free! Find your manual ZUMLINK-DT-QUATTRO-DLS-RLY - Crestron and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ZUMLINK-DT-QUATTRO-DLS-RLY by Crestron.

USER MANUAL ZUMLINK-DT-QUATTRO-DLS-RLY Crestron

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : Crestron

Model : ZUMLINK-DT-QUATTRO-DLS-RLY

Category : Motion detector