Omnia M 3.2 - Boiler FERROLI - Free user manual and instructions
Find the device manual for free Omnia M 3.2 FERROLI in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Wall-hung gas boiler |
| Brand | Ferroli |
| Model | Omnia M 3.2 |
| Energy Source | Natural gas / LPG |
| Heat Output | 24 kW |
| Efficiency | Class A (up to 93%) |
| Dimensions (H x W x D) | 700 x 400 x 250 mm |
| Weight | 28 kg |
| Water Heating | Combi (instantaneous DHW) |
| DHW Flow Rate | 13.5 l/min at ΔT 30°C |
| Noise Level | < 55 dB(A) |
| Flue Type | Room-sealed (balanced flue) |
| Pressure Gauge | Analog, range 0-4 bar |
| Safety Features | Overheat protection, frost protection, gas leak detection, flame failure device |
| Maintenance | Annual service recommended by qualified technician |
| Spare Parts Availability | Genuine Ferroli parts available through authorized dealers |
| Installation Requirements | Must be installed by a Gas Safe registered engineer |
| Warranty | 2 years (extendable with registration) |
Frequently Asked Questions - Omnia M 3.2 FERROLI
How do I reset the Ferroli Omnia M 3.2 boiler?
Press and hold the reset button (usually a red button on the control panel) for 3 seconds. If the boiler does not restart, check the gas supply and water pressure.
What should the water pressure be on the Omnia M 3.2?
The recommended water pressure is between 1.0 and 1.5 bar when cold. If it drops below 0.5 bar, repressurize using the filling loop. Refer to the manual for exact instructions.
Why is my Ferroli Omnia M 3.2 not heating water?
Possible causes: no power, low water pressure, air in the system, or a faulty thermostat. Check the display for error codes and consult the manual.
How do I bleed the radiators with this boiler?
Turn off the heating system and wait for it to cool. Use a radiator key to open the bleed valve on each radiator until water trickles out, then close. Check boiler pressure afterwards.
What does the error code 'E01' mean on the Omnia M 3.2?
Error code E01 typically indicates a flame failure. This could be due to a gas supply issue, faulty ignition electrode, or flue blockage. Contact a professional.
How often should I service the Ferroli Omnia M 3.2?
An annual service by a Gas Safe registered engineer is recommended to maintain efficiency and safety. This includes checking the burner, heat exchanger, and safety devices.
Can I use the Omnia M 3.2 with LPG?
Yes, the boiler can be converted for LPG use. This requires a conversion kit and must be performed by a qualified technician. The manual covers the procedure.
What is the maximum heating output in kW?
The Ferroli Omnia M 3.2 has a maximum heating output of 24 kW. It is suitable for most medium-sized homes.
How do I adjust the room temperature?
Use the thermostat (if connected) or the boiler's control panel to set the desired flow temperature. For precise room temperature, install a room thermostat.
Where can I download the user manual?
The user manual can be downloaded for free from notice-facile.com or the official Ferroli website. Search for 'Ferroli Omnia M 3.2 manual' in PDF format.
User questions about Omnia M 3.2 FERROLI
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Boiler in PDF format for free! Find your manual Omnia M 3.2 - FERROLI and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Omnia M 3.2 by FERROLI.
USER MANUAL Omnia M 3.2 FERROLI
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : FERROLI
Model : Omnia M 3.2
Category : Boiler