EX-42034IS - Uncategorized EXSYS - Free user manual and instructions
Find the device manual for free EX-42034IS EXSYS in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Industrial Serial Device Server |
| Model | EX-42034IS |
| Brand | EXSYS |
| Serial Ports | 1 x RS-232/422/485 DB9 male |
| Ethernet Port | 1 x RJ45 10/100 Mbps |
| Power Input | 12-48 VDC (terminal block) |
| Dimensions | 95 x 66 x 22 mm (3.74 x 2.60 x 0.87 in) |
| Weight | 135 g (4.76 oz) |
| Operating Temperature | -40°C to 85°C (-40°F to 185°F) |
| Protocols | TCP/IP, UDP, Telnet, Modbus TCP, HTTP, SNMP |
| Configuration | Web interface, Windows utility, Telnet |
| LED Indicators | Power, Link/Activity, Serial Tx/Rx |
| Mounting | DIN rail or panel mount |
| Safety Certifications | CE, FCC Class A, UL |
| Warranty | 5 years |
| Package Contents | Device, quick start guide, power terminal block |
| Serial Baud Rate | Up to 921600 bps |
| Data Bits | 5, 6, 7, 8 |
| Stop Bits | 1, 1.5, 2 |
| Parity | None, Even, Odd, Mark, Space |
| Flow Control | None, RTS/CTS, XON/XOFF |
| Maximum Connections | Up to 16 TCP sessions |
| Software Tools | EXSYS Device Manager, Virtual COM port driver |
Frequently Asked Questions - EX-42034IS EXSYS
How do I assign an IP address to the EX-42034IS?
You can assign an IP address using the EXSYS Device Manager utility (Windows), via the web interface (default IP 192.168.1.1), or by DHCP. Refer to the manual for step-by-step instructions.
What serial interfaces are supported?
The EX-42034IS supports RS-232, RS-422, and RS-485 (2-wire or 4-wire). Interface selection is via DIP switches on the device.
How can I reset to factory defaults?
Press and hold the reset button (located near the power terminal) for 10 seconds while power is on. The device will reboot with factory settings.
What power supply is required?
The device accepts 12-48 VDC via the terminal block. It draws less than 2W. Use a regulated power supply with sufficient current (min 300mA).
Can I use the EX-42034IS with Modbus devices?
Yes, it supports Modbus TCP and can bridge Modbus RTU/ASCII over serial. Configure the serial parameters and enable Modbus gateway mode in the web interface.
How do I mount the device on a DIN rail?
Attach the DIN rail clip (included) to the rear of the device. Snap the device onto a standard 35mm DIN rail. Ensure it locks securely.
The device is not connecting to the network. What should I check?
Verify the Ethernet cable is properly connected, the link LED is on, and the device has a valid IP address. Try pinging the device. If using auto-IP, ensure no conflicts.
What is the operating temperature range?
The EX-42034IS is rated for -40°C to 85°C (-40°F to 185°F), making it suitable for harsh industrial environments.
Does the device support virtual COM port?
Yes, install the EXSYS Virtual COM Port driver (available on the website). It allows legacy serial applications to access the device over TCP/IP.
How do I update the firmware?
Download the latest firmware from the EXSYS website. Access the device web interface, go to Administration > Firmware Upgrade, and upload the file. Do not power off during update.
User questions about EX-42034IS EXSYS
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual EX-42034IS - EXSYS and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. EX-42034IS by EXSYS.
USER MANUAL EX-42034IS EXSYS
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : EXSYS
Model : EX-42034IS
Category : Uncategorized