M-12 - Effect machine Antari - Free user manual and instructions
Find the device manual for free M-12 Antari in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product type | Effect machine (fog machine) |
| Brand | Antari |
| Model | M-12 |
| Dimensions (L x W x H) | 520 mm x 310 mm x 230 mm (approx.) |
| Weight | 5.5 kg (approx.) |
| Power supply | 230 V / 50 Hz (or 120 V / 60 Hz for some markets) |
| Power consumption | 1500 W |
| Heater output | 1000 W |
| Output capacity | Approx. 150 m³/min |
| Warm-up time | Approx. 3.5 minutes |
| Fluid tank capacity | 1.5 L |
| Fluid consumption | Approx. 50 mL/min at maximum output |
| Control methods | Manual, remote control (included), DMX |
| Remote control | Wired remote (3-pin XLR) with timer and interval control |
| DMX channels | 1 or 2 channels (switchable) |
| Fuse type | 6.3 A / 250 V (5x20 mm) |
| Cleaning method | Run distilled water through system; wipe exterior with damp cloth |
| Safety features | Thermal cut-off; auto-shutoff when fluid level low |
| Maintenance | Regular cleaning after every 40 hours of use to prevent clogging |
| Spare parts | Fuse, heating element, pump, fluid tank, remote control, XLR cable |
| Warranty | 1 year limited warranty |
| Certifications | CE, UL, RoHS |
Frequently Asked Questions - M-12 Antari
How do I clean the Antari M-12 fog machine?
Run a solution of distilled water through the system to flush out residual fluid. Turn off and unplug, then wipe the exterior with a damp cloth. Do not use solvents.
What type of fog fluid should I use with the M-12?
Use only Antari original fog fluid for best performance. Avoid using oil-based or other non-water-based fluids as they can damage the heater.
How long does it take for the M-12 to warm up?
The warm-up time is approximately 3.5 minutes. The green LED will indicate when the machine is ready.
Can the M-12 be used with DMX controllers?
Yes, the M-12 supports DMX control on 1 or 2 channels. Use a DMX cable (3-pin XLR) and set the DMX address via the DIP switches.
What should I do if the fog output is weak?
First check the fluid level. If it's fine, the heater or pump may need cleaning. Run distilled water through the system for 10 minutes to clear clogs. If problem persists, check the fuse and heater element.
How do I set the remote control timer on the M-12?
The wired remote has two knobs: Duration (how long fog is output) and Interval (pause between bursts). Turn knobs to desired settings. The machine will cycle automatically.
What does the red LED on the M-12 indicate?
A red LED indicates that the machine is still warming up or has reached its maximum temperature (overheat) and has shut off. If constant, check for overheating and allow the machine to cool.
Is the Antari M-12 safe to use indoors?
Yes, but ensure adequate ventilation. The fog is non-toxic and water-based, but can reduce visibility. Do not point at people or animals. Keep away from heat sources.
What are the spare parts available for the M-12?
Common spare parts include: fuse (6.3A/250V), heating element, pump assembly, fluid tank, and remote control. Contact Antari or an authorized dealer for replacements.
How do I replace the fuse on the M-12?
Unplug the machine. Locate the fuse holder near the power inlet. Use a flathead screwdriver to open it. Replace with a 6.3A/250V fuse of the same type. Close the holder and test.
User questions about M-12 Antari
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Effect machine in PDF format for free! Find your manual M-12 - Antari and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. M-12 by Antari.
USER MANUAL M-12 Antari
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Antari
Model : M-12
Category : Effect machine