09706 - Paint gun Draper - Free user manual and instructions
Find the device manual for free 09706 Draper in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Paint Spray Gun |
| Model | 09706 |
| Brand | Draper |
| Spray Technique | HVLP (High Volume Low Pressure) |
| Air Inlet | 1/4 inch NPT |
| Operating Air Pressure | 40-60 psi (2.8-4.1 bar) |
| Fluid Nozzle Size | 1.4 mm (standard) |
| Spray Pattern | Adjustable: round to fan |
| Fluid Cup Capacity | 600 ml (20 oz) |
| Cup Type | Gravity feed (top-mounted) |
| Weight (approx.) | 0.6 kg (1.3 lbs) |
| Dimensions (LxWxH) | 250 x 100 x 200 mm |
| Material | Aluminum body, brass nozzle |
| Recommended Paint Viscosity | 20-25 seconds (Ford #4 cup) |
| Adjustable Fluid Control | Yes |
| Adjustable Air Control | Yes |
| Maintenance | Clean with thinner after each use |
| Safety Features | Trigger lock, air pressure relief |
| Spare Parts Available | Nozzle sets, needle, air cap, seals |
| Repairability | Replaceable parts; service kits available |
Frequently Asked Questions - 09706 Draper
How do I clean the Draper 09706 paint gun?
Disconnect the air supply and remove the paint cup. Flush the gun with appropriate solvent (e.g., mineral spirits for oil-based paints) by spraying through until clean. Wipe exterior surfaces and allow to dry. Disassemble nozzle for thorough cleaning if needed.
What air pressure should I use?
The recommended operating air pressure is between 40-60 psi (2.8-4.1 bar). Adjust the pressure according to the paint viscosity and desired spray pattern.
Can I use water-based paints with this gun?
Yes, the Draper 09706 is compatible with water-based paints. Ensure to clean the gun thoroughly with water after use to prevent clogging.
How do I adjust the spray pattern?
Turn the air control knob on the rear of the gun to adjust the fan width. Rotate clockwise for a round pattern, counterclockwise for a flat fan pattern. Use the fluid control knob to adjust paint flow.
What does the 1.4 mm nozzle mean?
The 1.4 mm nozzle size indicates the diameter of the fluid tip opening. It is suitable for medium-viscosity paints such as primers, basecoats, and clearcoats. For thicker materials, a larger nozzle may be needed.
Why is there spitting or uneven spray?
Spitting usually indicates a loose fluid nozzle or needle, or debris in the nozzle. Ensure all parts are tightened. Clean the nozzle and check for damage. Also verify that the paint is properly thinned and filtered.
How do I disassemble the gun for deep cleaning?
Remove the air cap by unscrewing it. Unscrew the fluid nozzle with a wrench. Pull out the needle from the rear after loosening the needle adjustment knob. Clean each part with solvent and reassemble in reverse order.
What safety precautions should I take?
Always wear a respirator mask, safety glasses, and gloves. Work in a well-ventilated area away from open flames. Do not exceed the maximum air pressure. Engage the trigger lock when not in use.
Where can I find replacement parts?
Replacement nozzle sets, needles, air caps, and seal kits are available from Draper or authorized dealers. Check the user manual for part numbers or visit the Draper website.
What is the cup capacity and how do I fill it?
The gravity-feed cup holds up to 600 ml (20 oz). Unscrew the cup from the top of the gun, fill with strained paint, and reattach securely. Ensure the vent hole on the cup lid is open for proper flow.
User questions about 09706 Draper
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Paint gun in PDF format for free! Find your manual 09706 - Draper and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 09706 by Draper.
USER MANUAL 09706 Draper
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Draper
Model : 09706
Category : Paint gun