NFI-U08-2A - Switch Tripp Lite - Free user manual and instructions
Find the device manual for free NFI-U08-2A Tripp Lite in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Unmanaged Network Switch |
| Brand | Tripp Lite |
| Model | NFI-U08-2A |
| Number of Ports | 8 Gigabit Ethernet ports (10/100/1000 Mbps) |
| Uplink Ports | 2 Gigabit SFP combo ports (fiber) |
| Dimensions (L x W x H) | 17.2 x 10.2 x 3.0 cm |
| Weight | 0.5 kg |
| Power Supply | External adapter 5 V DC, 1 A (5 W) |
| Power Consumption | 5 W maximum |
| Operating Temperature | 0 °C to 40 °C |
| Relative Humidity | 10 % to 90 % (non-condensing) |
| Supported Network Standards | IEEE 802.3, 802.3u, 802.3ab, 802.3x, 802.1p, 802.1q |
| Main Features | Auto-negotiation, auto-MDI/MDIX, flow control, Jumbo frames (9,000 bytes), port-based QoS |
| Switching Method | Store-and-forward |
| MAC Address Table | 8,000 entries |
| Total Bandwidth | 16 Gbit/s (non-blocking) |
| Maintenance and Cleaning | Unplug the device before cleaning. Use a soft, dry cloth. Do not use chemicals. |
| Safety | CE, RoHS standards. Use only the provided adapter. Do not expose to water or extreme temperatures. |
| Spare Parts and Repairability | No user-repairable parts. In case of failure, contact Tripp Lite support or an authorized service center. |
| Warranty | 3 years |
| General Information | Unmanaged switch, plug-and-play installation. Metal casing, wall-mountable (kit included). |
Frequently Asked Questions - NFI-U08-2A Tripp Lite
How do I connect the NFI-U08-2A switch?
Connect the provided power adapter, then connect your devices (PC, printer, etc.) to the Ethernet ports using RJ45 cables. The switch operates in plug-and-play mode: no configuration required.
The power LED does not light up, what should I do?
Check that the power adapter is properly plugged in and the wall outlet works. If the LED remains off, try another compatible adapter (5 V, 1 A). If the problem persists, contact Tripp Lite support.
Can I use Category 5e or 6 cables?
Yes, the switch supports Cat5e, Cat6, and Cat6a cables for Gigabit speeds. Make sure the cables are in good condition to avoid connection losses.
How do I use the SFP ports?
The SFP ports (fiber) require compatible SFP modules (not included). Insert the module into the port, then connect the fiber cable. The SFP ports share the last two copper ports (7 and 8): they cannot be used simultaneously.
Does the switch support VLAN?
This model is unmanaged, it does not support VLAN. For advanced features like VLAN, choose a managed switch (e.g., Tripp Lite NG series).
What is the maximum power consumption?
Consumption is about 5 W in normal use. This allows 24/7 operation without significant energy cost.
Can I mount the switch on a wall?
Yes, the metal casing is designed for wall mounting. Use the brackets and screws provided in the mounting kit. Ensure the wall can support the weight (0.5 kg).
How do I clean the switch?
Unplug the device. Use a soft, dry cloth to dust the casing. Never use liquids or abrasive products, as they could damage the electronics.
What to do if a device is not recognized?
Check the connections and try another port. Make sure the device is powered on and its network adapter works. The switch auto-negotiates speed and duplex, so no settings are needed.
Does the switch get hot?
The metal casing dissipates heat well. Under normal operation, it may become warm but not hot. Ensure adequate ventilation around the device and do not stack it with other hot equipment.
User questions about NFI-U08-2A Tripp Lite
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Switch in PDF format for free! Find your manual NFI-U08-2A - Tripp Lite and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. NFI-U08-2A by Tripp Lite.