ELPMB75 - Projector EPSON - Free user manual and instructions

Product type	Ceiling mount for projector
Brand	Epson
Model	ELPMB75
Material	Robust steel with black finish
Adjustable height	Yes, up to 60 cm drop
Tilt	±15°
Rotation	360°
Maximum load capacity	15 kg
Compatible with	Epson and other brand projectors (VESA standard)
VESA standard	100x100 mm to 200x200 mm
Mounting type	Ceiling (concrete, wood, plaster)
Tube length	30 cm
Net weight	2.5 kg
Dimensions (L x W x H)	30 x 30 x 50 cm
Color	Black
Installation	Mounting kit included, screws provided
Maintenance	Clean with a soft dry cloth
Security	Optional anti-theft lock
Warranty	2 years

Frequently Asked Questions - ELPMB75 EPSON

What type of ceiling is suitable for installing the Epson ELPMB75 mount?

The mount is designed for ceiling installation on concrete, wood or plaster (with appropriate anchors). Ensure the structure can support at least 15 kg.

My projector is not Epson brand, can I use this mount?

Yes, the mount is compatible with most projectors that comply with the VESA standard (100x100 mm to 200x200 mm). Check your projector's mounting points.

How to adjust the tilt of the projector on this mount?

The mount has a tilt adjustment knob of ±15° and a 360° rotation. Loosen the locking screw slightly, adjust the angle, then tighten.

What is the maximum drop height of the tube?

The telescopic tube allows a drop of up to 60 cm. You can also shorten it according to your ceiling height.

Is the mount delivered with screws for the projector?

Yes, the kit contains several sets of screws suitable for common VESA standards (M4, M5, M6). Use the longest screws that fit into the projector inserts without protruding.

Can I install this mount alone or do I need two people?

It is recommended to have two people to secure the projector during ceiling installation. The mount alone weighs 2.5 kg, but with the projector, the assembly becomes heavier.

Does the mount allow hiding cables?

Yes, the mount tube is hollow and allows cables (HDMI, power) to be routed inside for a cleaner appearance.

What is the maximum load capacity of the ELPMB75?

The maximum load is 15 kg. Check your projector's weight before installation.

How to maintain the ceiling mount?

Clean it with a soft dry cloth. Do not use abrasive products or solvents that could damage the paint.

Is there an integrated anti-theft system?

The mount has a security hole (anti-theft cable optional, not included). You can attach a padlock or cable to secure the projector.

USER MANUAL ELPMB75 EPSON

ELPMB75 User's Guide

1

EN	1 Stick the template sheet in the installation position. See the "Installation Guide" for more information on how to determine the installation position.2 From the screw holes shown in the figure above, secure at least four points at the top, bottom, left, and right for optimum balance.3 Remove the template sheet.
FR	1 Collez la feuille modèle dans la position d'installation. Consultez le "Guide d'installation" pour plus d'informations sur la détermination de la position d'installation.2 À partir des trous de vis indiqués sur l'illustration ci-dessus, fixez au moins quatre points en haut, en bas, à gauche et à droite pour une équilibre optimal.3 Retirez la feuille modèle.
DE	1 Kleben Sie die Schablone an die Installationsposition. Weitere Informationen zur Ermittlung der Installationsposition finden Sie in der „Installationsanleitung".2 Verwenden Sie für optimale Balance mindestens 4 der in der Abbildung oben gezeigten Schraubenlöcher oben, unten, links und rechts.3 Entfernen Sie die Schablone.
ES	1 Pegue la hoja de la plantilla en la posición de instalación. Consulte la "Guía de instalación" para obtener más información sobre cómo determinar la posición de instalación.2 Desde los orificios de tornillo mostrados en la figura anterior, fijé al menos cuatro puntos en la parte superior, inferior, izquierda y derecha para conseguir un equilibrio óptimo.3 Retire la hoja de la plantilla.
IT	1 Incollare il foglio del modello nella posizione di installazione. Consultare la "Guida di installazione" per maggiori informazioni su come stabilire la posizione di installazione.2 Dai fori per le vite mostrati nella figura di sopra, fissare almeno quattro punti in alto, in basso, a sinistra e a destra per un equilibrio ottimale.3 Rimuovere il foglio del modello.
PT	1 Cole a folha de modelo na posição de instalação. Para mais informações sobre a posição de instalação, consulte o "Manual de instalação".2 Nos orificios de parafuso mostrados na figura acima, fixe pelo menos quatro pontos na parte superior, inferior, esquerda e direita para um equilibrio ideal.3 Retire a folha de modelo.
SC	1 将模板纸贴在安装位置。更多关于如何确定安装位置的信息,请参见“安装手册”。2 从上图所示的螺栓孔,在顶部、底部、左侧和右侧固定至少四个点,以保证最佳平衡。3 取下模板纸。
TC	1 將模板貼在安装位置。請參閱「安裝説明書」進一步瞭解如何決定安裝位置。2 在上圖所示的螺絲孔中,至少固定上、下、左、右四個點,以達到最佳平衡。3 拆下模板。
KO	1 템플릿 시트를 설치 위치에 부착합니다. 설치 위치를 확인하는 방법에 대한 자세한 내용은 "설치 가이드"를 참조하십시오.2 위 그림에 표시된 나사 구멍 중에서 상하좌우로 최소 4 개의 지점을 고정하여 최적의 균형을 유지합니다.3 템플릿 시트를 제거합니다.
JA	1 設置する位置にテンプレートシートを貼ります。設置位置の決め方は『設置工事説明書』をご覧ください。2 上図のネジ穴の中から、上下左右で均等にバランスがとれる 4 箇所以上を固定します。3 テンプレートシートを外します。

2

3

4

5

6

EN	Press the [Menu] button, and then select [Installation] > [Setting Plate Installation Guide]. Adjust the position of the image according to the screen.
FR	Appuyez sur le bouton [Menu], puis sélectionnez [Installation] >[Guide d'installation de la plaque d'installation]. Ajustez la position de l'image en fonction de l'écran.
DE	Drücken Sie die [Menu]-Taste und wählen Sie [Installation] > [Einstellungsplatte-Installationsanleitung]. Passen sie die Bildposition entsprechend dem Bildschirm an.
ES	Presione el botón [Menu] y, a continuación, seleccione [Instalación] > [Guía de instalación de la placa de fijación]. Ajusta la posición de la imagen conforme a la pantalla.
IT	Premere il tasto [Menu] e quindi selezionare [Installazione] > [Guida all'installazione della piastra di installazione]. Regolare la posizione dell'immagine in base allo schermo.
PT	Prima o botão [Menu] e seleccione [Instalação] > [Guía de Instalação da placa de montagem]. Ajuste a posição da imagem de acordo com o ecrã.
SC	按 [Menu] 按钮,然后选择 [安装] > [安装支架安装指南]。按照屏幕调整图像位置。
TC	按 [Menu] 按钮,然後選擇 [安装] > [安装支架安装指南]。根據螢幕調整影像的位置。
KO	[Menu] 버튼을 누른 후 [설치] > [고징 플레이트 설치 설명서]를 선택합니다. 화면에 따라 이미지 위치를 조정합니다.
JA	【Menu】ボタンを押して、[設置]-[セッティングプレート調整ガイド]を選択します。画面に従って映像の位置を調整してください。

Installation Guide

About This Installation Guide

This guide describes how to mount the ultra-short-throw projectors listed below to a wall using the Epson® ELPMB75 wall mount.

The following projectors are covered by this guide:

- EB-810E/EB-815E

The EB-810E is shown in most illustrations in this guide, but the steps are the same for all models unless otherwise noted.

Safety Instructions

For your safety, read all the instructions in this guide before using the wall mount. Incorrect handling that ignores instructions in this guide could damage the wall mount or could result in personal injury or property damage. Keep this installation guide on hand for future reference.

Read the safety instructions in the online User's Guide for your projector and follow the instructions in this document.

Explanation of Symbols

The warning marks shown below are used throughout this installation guide to prevent personal injury or property damage. Make sure you understand these warnings when reading this installation guide.

Warning	This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
Caution	This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
	This symbol indicates related or useful information.
	Symbol indicating an action that must not be done
	Symbol indicating an action that should be done

Safety Precautions for Installation

Warning
The wall mount is designed specifically for mounting a projector to a wall. If anything other than a projector is mounted, the weight may result in damage.If the wall mount falls, it could cause personal injury or property damage.
The installation work (wall mounting) should be performed by specialists who have technical knowledge and ability. Incomplete or incorrect installation could cause the wall mount to fall and cause personal injury or property damage.
Follow the steps in this guide to install the wall mount, and be sure to use the bolts and screws specified in this guideIf the instructions are not followed, this product may fall, resulting in personal injury or an accident.
Handle the power cord carefully. Incorrect handling may cause fire or electric shock. Observe the following precautions when handling: Do not handle the power plug with wet hands. Do not use a power cord that is damaged or modified. Do not pull the power cord with too much force when routing the cable through the wall mount.
Do not install the wall mount in a place where it might be subjected to vibration or shock. Vibration or shock could cause damage to the projector or mounting surface. It could also cause the wall mount or projector to fall and cause personal injury or property damage.
The installation work should be performed by at least two qualified service personnel. If you need to loosen any screws during installation, be careful not to drop the wall mount. If the wall mount or projector falls, it could cause personal injury or property damage.
Make sure you use the included safety wire kit when mounting your projector.
Install the wall mount so that it can sufficiently support the weight of the projector and wall mount, and resist any horizontal vibration. Use M10 or 3/8 inch x 60 mm nuts and bolts and make sure to use appropriate wall anchors for your wall type. Nuts and bolts smaller than M10 or 3/8 inch x 60 mm could cause the wall mount to fall. Epson accepts no responsibility for any damage or injury caused by lack of wall strength or inadequate installation.
When you mount the projector on the wall with the wall mount, the wall must be strong enough to hold the projector and the wall mount. This product should be installed on a concrete wall. The maximum combined weight of the projector and wall mount is approximately 48.5 lb (22 kg) not including cables. If the wall is not strong enough, reinforce the wall before installation.
Inspect the wall mount on a regular basis to ensure there are no broken parts or loose screws. If there are any broken parts, stop using the wall mount immediately. If the wall mount or projector falls, it could cause personal injury or property damage.
Never modify the wall mount.
Do not disassemble or modify the projector. There are numerous high-voltage sections inside the product that could cause a fire, electric shock, or an accident.
Do not hang on the wall mount or hang a heavy object on the wall mount. If the projector or wall mount falls, it could cause personal injury or property damage.
Do not use adhesives, lubricants, or oils to install or adjust the wall mount. If you use adhesives to prevent the screws from loosening or things such as lubricants or oils on the part of the projector attached to the slide plate, the case may crack and cause the projector to fall, resulting in personal injury or property damage.
Tighten all screws firmly after adjustment. Otherwise, the projector or wall mount may fall and cause personal injury or property damage.
Never loosen the bolts and nuts after installation. Confirm that the screws have not become loose on a regular basis. If you find any loose screws, tighten them firmly. Otherwise, the projector or wall mount may fall and cause personal injury or property damage.
When performing wiring, make sure the cable does not come into contact with any screws or bolts. Handling the cable incorrectly may cause fire or electric shock.
Do not install in a location subject to oily smoke or smoke for events. If oils stick to the slide plate fixing part of the projector, the case may crack and cause the projector to fall, resulting in personal injury or property damage.
When turning on the projector, do not look into the projection lens. This could cause damage to eyesight due to the powerful light emitted. Take particular care when there are children present. When turning on the projector at a distance using the remote control, make sure there is no one looking into the projection lens.
When using the projector, do not place any objects or put your hand near the projection lens.This area is dangerous as it reaches a high temperature due to the concentrated projection light.
Do not use the projector in a location subject to combustible or explosive gas.High temperature within the projector may cause ignition and a fire to occur.
Only a specialist should remove or reinstall the projector, including for maintenance and repairs.See the projector's User Guide for instructions on maintenance and repairs.
If any abnormalities occur with the product, immediately disconnect the cables from the product, and then contact Epson.Continuing to use the product in an abnormal condition could cause a fire, electric shock, or visual impairment.
Never open any cases on the projector.Electrical voltages inside the projector can cause severe injury.
Do not look directly into the projector's light source.This product may emit hazardous optical radiation that can cause eye injury.

Caution

Do not install the wall mount in a location where the operating temperature for your projector model may be exceeded. Such an environment may damage the projector.

Install the wall mount in a place free from excessive dust and humidity to prevent the lens or optical components from becoming dirty.

Do not use excessive force when adjusting the wall mount.

The wall mount may break, resulting in personal injury.

Do not disassemble the projector when disposing of it.

Dispose according to your local or national laws and regulations.

This projector is a Class 1 laser product that complies with the IEC/EN0825-1: 2014 international standard for lasers.

• Before installing the projector, verify the power supply wiring for the installation location. - We suggest projecting onto a sturdy surface like a wall or whiteboard. To prevent any image distortion on a screen, make sure that the screen remains stationary and doesn't sway due to air currents. - For optimal results with extreme short throw projection, it is crucial to use a flat projection surface. When using a projection screen, make sure it is pulled tight and flat to avoid any distortion. Avoid roll-up screens as they tend to be uneven when unrolled and can result in distorted images. - Install and adjust the projector at a room temperature that is close to the actual intended usage environment. If the temperature changes, the position of the image may shift. - If you want to hide the projector power plug under the wall plate cover, make sure the power outlet is located in the empty space to the left or right of the wall plate. • Install the projector away from other electric devices such as fluorescent lights or air conditioners. Some kinds of fluorescent lights could interfere with the remote control of the projector. • Install the projector away from direct sunlight and other bright light sources.

- To ensure proper ventilation, it is important to leave a minimum of 13.7 inches (35 cm) of space on the right side and 3.7 inches (10 cm) of space on the left side between the wall and the projector's exhaust. Additionally, the intake vents located on the top right of the projector require a space of 8.2 inches (21.2 cm) between the wall and the projector.

- Install the projector at an angle of no more than 3 degrees horizontally or vertically in relation to the projection surface.

- You can also use the Epson Projector Throw Distance Simulator at http://epson.com/support/calculators (U.S.), http://epson.ca/support/calculators (Canada), or http://epson.com.jm/support/calculators (Latin America) to determine the correct measurements. (Conversion figures may have been rounded up or down.)

- When installing two or more projectors, check the following:

• Make sure the temperature of the surrounding environment is less than 95°F (35°C). If the environment is too hot, the projectors may overheat and the power may turn off without warning. • Make sure you leave a gap of at least 29.5 inches (75 cm) between the projectors.

If the projectors are installed closer than 29.5 inches (75 cm) apart, install a partition to block the heat from the projector's exhaust vents. The partition should be larger than the exhaust vents and installed approximately 13.7 inches (35 cm) from the exhaust vents and 3.9 inches (10 cm) from the intake vent.

1 Package Contents 8

2 Specifications 10

3 Connecting Devices 13

4 Positioning the Projector 14

Installation worksheet for projecting on a whiteboard 14 Installation worksheet for projecting on a plain wall 16 Projection distance worksheets 17 Diagonal image size and mounting position 18 Distance from top of projected image to wall plate 19 Installation measurement tables 19

5 Installing the Projector 25

Assemble the parts 25 Install the wall plate on the wall 27 Determine the projection distance and pull out the mount arm slider 30 Attach the arm unit to the wall plate 31 Route the cables through the arm unit. 32 Adjust the vertical slide position of the arm 34 Attach the projector to the wall mount 35 Attach a Mini PC or Stick PC if necessary 36

6 Adjusting the Image 38

Display the Setting Plate Installation Guide 38 Use adjustment dial 1 on the left side to adjust the horizontal roll 39 Use adjustment dial 2 on the top to adjust the horizontal rotation 39 Use adjustment dial 3 on the front to adjust the vertical tilt 40 Adjust the horizontal slide 40 Adjust the forward/backward slide 41 Adjust the vertical slide 41 Adjust the focus 42 Press the [Esc] button on the remote or control panel to exit the guidance screen after adjusting.

7 Attaching the Covers 43

Attach the wall plate cover and end cap 43

8 Appendix

Making Screen Adjustments

Attaching a Security Cable

Attaching a Safety Wire

Wall Mount

# Part name
1	E	n	d	c	a	p
2 3-axis adjustment unit and slide plate (attached when shipped)
3	A	r	m	u	n	i t
4 Wall plate
5 Wall plate covers
6 Hexagonal shaft

Hardware

Shape Name	Quantity Application
	M4 × 12 mm hexagon socket head cap bolt with washer/spring washer	5 For wall	plate assembly
		4 For 3-axis	is adjustment unit/wall mount installation
		4 For slide	plate/projector installation
	M6 × 20 mm hexagon shoulder head bolt with washer/spring washer	1 For wall	mount/wall plate installation
	M6 × 20 mm cross recessed head shoulder screw with plastic washer	3
[KZW3]	M3 × 6 mm cross recessed head shoulder screws 4		For Mini PC plate installation

• Use the bolts or screws supplied with the wall mount to install it as directed in this guide. Do not substitute these bolts with any other types.
• You need to use commercially available M10 × 60 mm or 3/8 inch anchors (at least 4) and one M10 screw to attach the wall plate to the wall.
• Gather the tools and parts you need before you begin installation, including a 17 mm ratchet wrench (for adjusting the hexagonal axis).

Accessories

Template sheet (for installing the wall plate)

Safety wire installation kit (for securing the projector)

Mini PC plate

Masking sticker

Open-ended wrench 13 mm (for M6) × 6 mm

Hexagon Wrench (for M4)

Rubber Caps

2 Specifications

Item Specification	Additional information		Reference page
Wall mount weight (including the 3-axis adjustment unit, slide plate, wall plate, wall plate cover, and end cap)	Approx. 20.9 lb (9.5 kg)	—	—
Maximum load capacity 33.1 lb (15.0 kg) — —
Vertical slide adjustment range ±1.6 in. (40 mm) — Refer to the			illustration on p. 11
Horizontal slide adjustment range ±1.8 in. (45 mm) — Refer to the			illustration on p. 11
Forward/backward slide adjustment range	0 to 10.4 in. (0 to 266 mm)	Determine adjustment unit installation position based on screen size	Refer to the illustration on p. 12
Horizontal roll adjustment range ±3° Fine adjustments possible with adjustment dial			p. 39
Horizontal rotation adjustment range	±8° Fine adjustments possible with adjustment knob		p. 39
Vertical tilt adjustment range	±3° Fine adjustments possible with adjustment dial		p. 40

Wall plate cover

Wall plate

The wall plate is in three pieces when shipped. Use the included M4 × 12 mm bolts (×5) to attach the separate pieces together before mounting the projector. See page 25 for instructions.

Vertical slide adjustment range

Horizontal slide adjustment range

Forward/backward slide adjustment range

Arm slide adjustment range

Adjustment from 3-axis adjustment unit installation position

By changing the installation position of the 3-axis adjustment unit to the front or back, you can adjust the installation position of the projector.

- Mount at the stamp when the image is less than 117 inches diagonally.

- Mount at the stamp when the projected image is 117 inches or more diagonally.

To see these stamps, you need to loosen the two top bolts and slide out the arm extension.

Make sure you have the power cord, computer cable, and other parts at the location where the wall mount is to be installed. Make sure you also have all necessary cables for the devices, such as a document camera that you will connect to the projector. Your projector's connection panel may differ slightly from the model in the illustrations. For details, refer to the online User's Guide for your projector.

Connection Example

Your Epson projector can project images up to the following sizes:

This guide covers select image sizes. For guidance on other image sizes, use the Epson Projector Throw Distance Simulator at http://epson.com/support/calculators (U.S.), http://epson.ca/support/calculators (Canada), or http://epson.com.jm/support/calculators (Latin America).

Projector	Maximum projected image size (diagonally)
	16:9 16:10	4:3 21:9 16:6
EB-810E/EB-815E 160 148 130 151 148

You can project onto a plain wall, screen, or pre-installed whiteboard.

The height of the included wall mount determines the maximum image size and how high the image appears on the wall. The distance from the projector to the wall (once it is mounted on the adjustable arm of the wall mount) also affects image size and position.

If you are planning to project on a whiteboard, the image may not fill the entire board, depending on the aspect ratio. If you match the image height to the board's height, gaps may appear on the sides of the board.

Use the following worksheets to determine the proper location of the wall plate on the wall. If you are projecting onto a whiteboard, use the worksheet below. If you are projecting on a plain wall, use the worksheet on page 16.

Installation worksheet for projecting on a whiteboard

1. Measure the ceiling height (distance from the floor to the ceiling). ____
2. Measure the height of the board's image area (h). ____ (h)
3. Measure the width of the board's image area (w). ____ (w)
4. Measure the distance from the floor to the bottom of the board's image area (f). ____ (f)
5. Measure the thickness of the board (distance from the projection surface to the wall) ____ (x)
6. Determine the aspect ratio of the board or of the images that will be projected. You may need to consult your IT department for this information.

____ 4:3 ____ 16:10 ____ 16:9 Widescreen ____ 16:6 ____ 21:9

If your desired aspect ratio does not match the native aspect ratio of your product, use the Epson Projector Throw Distance Simulator at http://epson.com/support/calculators (U.S.), http://epson.ca/support/calculators (Canada), or http://epson.com.jm/support/calculators (Latin America) to determine the correct measurements.

1. Using the tables on pages 20 to 24 and your desired image height (h), find the required distance between the top of the image area and the bottom holes of the wall plate (c). ____ (c)
2. Using the tables on pages 20 to 24 and your desired image height (h), find the required distance between the top of the image area and the temporary wall plate hole (d). ____ (d)
3. Add:

Required distance from top of image area to bottom holes of wall plate (c)	____(c)
Height of image area (h)	____(h)
Distance from floor to bottom of image area (f)	____(f)
Height of wall plate plus cover
If the total exceeds the ceiling height, you will need to reduce the image size or reduce the distance from the floor to the bottom of the image area.	+11 inches(280 mm)
	____total

1. After confirming your image size, use tape or a pencil to mark the distance (c) from the top of the image area on the board to the bottom holes of the wall plate.
2. Align the line (horizontal) on the template sheet with the (c) mark, then align the center line on the template sheet with the center of the image area. Follow the instructions on page 25 to install the projector.

Installation worksheet for projecting on a plain wall

1. Measure the ceiling height (distance from the floor to the ceiling).
2. Determine the aspect ratio of the images that will be projected. You may need to consult your IT department for this information.

____ 4:3 ____ 16:10 ____ 16:9 Widescreen ____ 16:6 ____ 21:9

If your desired aspect ratio does not match the native resolution of your product, use the Epson Projector Throw Distance Simulator at http://epson.com/support/calculators (U.S.), http://epson.ca/support/calculators (Canada), or http://epson.com.jm/support/calculators (Latin America) to determine the correct measurements.

1. Using the tables on pages 20 to 24, select the largest image size available for your ceiling height.

Image height (h) ____ (h)

Image width (w) ____ (w)

1. Determine the desired distance from the floor to the bottom of the image area (f). ____ (f)

The recommended minimum distance is 30 inches (762 mm). Images appearing less than 28 inches (711 mm) from the floor may be obstructed for some viewers.

1. Find the top of the projected image area by adding distances (f) and (h).
2. Use the tables on pages 20 to 24 to determine the required distance from the top of the image area to the bottom holes of the wall plate (c). ____ (c)
3. Use the tables on pages 20 to 24 to determine the required distance between the top of the image area and the temporary wall plate hole (d). ____ (d)
4. Add:

Required distance from top of image area to bottom holes of wall plate (c)	(c)
Height of image area (h)	(h)
Distance from floor to bottom of image area (f)	(f)
Height of wall plate plus cover	+ 11 inches
If the total exceeds the ceiling height, you will need to reduce the image size or reduce the distance from the floor to the bottom of the image area.	(280 mm)
	total

1. After confirming your image size, use tape or a pencil to mark the distance (c) from the top of the image area on the board to the bottom holes of the wall plate.
2. Align the horizontal line on the template sheet with the (c) mark, then align the center line on the template sheet with the center of the image area. Follow the instructions on page 25 to install the projector.

Projection distance worksheets

The tables on the following pages provide installation information for select image sizes. The minimum ceiling height is based on an image 30 inches (762 mm) from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

Use the worksheets, the illustrations, and the information in the tables on the following pages to determine the projection distance and placement of the wall plate.

Diagonal image size and mounting position

In order to see the stamp and the numbers on the slider scale (b), you need to loosen the two top bolts and slide out the arm extension.

- Mount the projector at the ○ stamp when the image is less than 117 inches diagonally.

- Mount the projector at the ○○ stamp when the image is 117 inches or more diagonally.

Distance from top of projected image to wall plate

The distance (c) from the top of the projected image to the bottom mounting holes on the wall plate is the number given when the vertical slide is set to the base position, as shown below.

Match the notch on the arm unit to the position of the stamp on the wall plate.

Installation measurement tables

See the following pages for your projector's installation measurement tables.

The measurements may differ depending on the location where you place the projector. When projecting in Tele mode, the quality of the projected images may decrease.

A shorter (x) distance may increase the minimum projection size.

Measurements in Inches for 16:9

						Default Screen Position
Diagonal image size (S)	Min. ceiling height*	Image width (w)	Image height (h)	Min. projection distance (a)	Sliderscale mark (b)	Distance from top of image to bottom wall plate holes (c)	Distance from top of image to temporary wall plate hole (d)
100"	99.2 87.1	49 3.8 0.0	5 9.2 16.7
105"	102.1 91	5 51.5 4.5	8 9.6 17.1
110"	104.9 95	8 53.9 5.3	1.5 10 17.5
115"	107.7 100	56.3 6		2.3 10.4 18
120"	110.6	104.5	58.8	6.7	.5	10.8	18.4
125"	113.5	108.9	61.3 7.5	1.3 11.2		18.8
130"	116.3	113.2	63.7	8.2	2	11.6	19.2
135"	119.1	117.5	66.1 9	2.8	12 19.5
140"	122 121	9 68	6 9.7 3.5 1	2.4 20
145"	124.8	126.2 71		10.4 4.2 12.8		20.4
150"	127.7	130.6	73.5	11.2	5	13.2	20.8
155"	130.5	134.9	75.9	11.9	5.7	13.6	21.2
160"	133.4	139.3	78.4	12.6 6.4 14	21.6

* Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

Measurements in Centimeters for 16:9

						Default Screen Position
Diagonal image size (S)	Min. ceiling height*	Image width (w)	Image height (h)	Min. projection distance (a)	Sliderscale mark (b)	Distance from top of image to bottom wall plate holes (c)	Distance from top of image to temporary wall plate hole (d)
100"	251.9	221.2	124.4	9.6	0.1	23.3	42.4
105"	259.3	232.4	130.8	11.4	2	24.3	43.4
110"	266.4	243.3	136.9	13.4	3.8	25.4	44.4
115"	273.5	254	143	15.2	5.8	26.4	45.7
120"	280.9	265.4	149.3	17	1.2	27.4	46.7
125"	288.2	276.6	155.7	19	3.3	28.4	47.7
130"	295.4	287.5	161.7	20.8	5	29.4	48.7
135"	302.5	298.4	167.8	22.8	7.1	30.4	49.5
140"	309.8	309.6	174.2	24.6	8.8	31.4	50.8
145"	316.9	320.5	180.3	26.4	10.6	32.5	51.8
150"	324.3	331.7	186.6	28.4	12.7	33.5	52.8
155"	331.4	342.6	192.7	30.2	14.4	34.5	53.8
160"	338.8	353.8	199.1	32	16.2	35.5	54.8

* Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

Measurements in Inches for 16:10

						Default Screen Position
Diagonal image size* (S)	Min. ceiling height**	Image width (w)	Image height (h)	Min. projection distance (a)	Sliderscale mark (b)	Distance from top of image to bottom wall plate holes (c)	Distance from top of image to temporary wall plate hole (d)
93"	100.1 78	4 49.9 3.9	0.1 9.2 16.8
95"	100.7 80	4 50.3 4.2	0.4 9.4 16.9
100"	103.7 84	6 52.9 5 1	2 9.8 17.4
105"	106.9 88	9 55.6 5.8	2 10.3 17.9
110"	109.9 93	1 58.2 6.6	2.8 10.7 18.3
115"	113 97.4	60.9 7.4	3.6 11.1 18.7
120"	116.1 10	1.6 63.5 8.2	2 2.2 11.6	19.2
125"	119.2 10	5.9 66.2 9	2.8 12 19.6
130"	122.3 11	0.2 68.9 9.8	3.6 12.4 20
135"	125.4 11	4.4 71.5	10.5	4.3	12.9 20.5
140"	128.4 11	8.5 74.1	11.4	5.2	13.3 20.9
145"	131.5 12	2.8 76.8	12.2	6	13.7 21.3
148"	133.4 12	5.4 78.4	12.6	6.4	14 21.6

* For images less than 99 inches, the projector's Tele settings must be used to reduce the image size. ** Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

Measurements in Centimeters for 16:10

						Default Screen Position
Diagonal image size* (S)	Min. ceiling height**	Image width (w)	Image height (h)	Min. projection distance (a)	Sliderscale mark (b)	Distance from top of image to bottom wall plate holes (c)	Distance from top of image to temporary wall plate hole (d)
93"	254.2	199.1	126.7	9.9	0.2	23.3	42.6
95"	255.7	204.2	127.7	10.6	1	23.8	42.9
100"	263.3	214.8	134.3	12.7	3	24.8	44.1
105"	271.5	225.8	141.2	14.7	5	26.1	45.4
110"	279.1	236.4	147.8	16.7	7.1	27.1	46.4
115"	286.9	247.3	154.6	18.7	9.1	28.1	47.4
120"	294.8	258	161.2	20.8	5.5	29.4	48.7
125"	302.7	268.9	168.1	22.8	7.1	30.4	49.7
130"	310.6	279.9	175	24.8	9.1	31.4	50.8
135"	318.5	290.5	181.6	26.6	10.9	32.7	52
140"	326.1	300.9	188.2	28.9	13.2	33.7	53
145"	333.9	311.9	195	30.9	15.2	34.7	54.1
148"	338.8	318.5	199.1	32	16.2	35.5	54.8

* For images less than 99 inches, the projector's Tele settings must be used to reduce the image size. ** Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

Measurements in Inches for 4:3

						Default Screen Position
Diagonal image size* (S)	Min. ceiling height**	Image width (w)	Image height (h)	Min. projection distance (a)	Sliderscale mark (b)	Distance from top of image to bottom wall plate holes (c)	Distance from top of image to temporary wall plate hole (d)
82"	99.3 65.4	49.1 3.9 0	1 9.2 16.8
85"	101.5 68	51 4.4 0.6	9.5 17.1
90"	104.9 71	8 53.9 5.3	1.5 10 17.6
95"	108.5 76	57 6.2 2.4	10.5 18
100"	112 80	60 7.1	3.3	11 18.6
105"	115.4 83	8 62.9 8		4.2 11.5 19
110"	118.9 87	8 65.9 8.9		5.1 12 19.5
115"	122.4 92	69 9.8	6	12.4 20
120"	125.9 95	8 71.9	10.7	4.5 13	20.5
125"	129.4	100	75	11.6	5.4	13.4	21
130"	132.8	103.8	77.9	12.5	6.3	13.9	21.5

* For images less than 99 inches, the projector's Tele settings must be used to reduce the image size. ** Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

Measurements in Centimeters for 4:3

						Default Screen Position
Diagonal image size* (S)	Min. ceiling height**	Image width (w)	Image height (h)	Min. projection distance (a)	Sliderscale mark (b)	Distance from top of image to bottom wall plate holes (c)	Distance from top of image to temporary wall plate hole (d)
82"	252.2	166.1	124.7	9.9	.2	23.3	42.6
85"	257.8	172.7	129.5	11.1	1.5	24.1	43.4
90"	266.5	182.3	136.9	13.4	3.8	25.4	44.7
95"	275.5 193	144.7	15.7 6		26.6	45.7
100"	259.1	203.2	127	18	8.3	27.9	47.2
105"	293.1	212.8	159.7	20.3	10.6	29.2	48.2
110"	301.9	223	167.3	22.6	12.9	30.4	49.5
115"	310.8	233.6	175.2	24.8	62.9	31.4	50.8
120"	319.8	243.3	182.6	27.1	68.8	33	52
125"	328.7	254	190.5	29.4	74.6	34	53.3
130"	337.3	263.6	197.8	31.7	80.5	35.3	54.6

* For images less than 99 inches, the projector's Tele settings must be used to reduce the image size. ** Based on an image 76.2 cm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

Measurements in Inches for 21:9

						Default Screen Position Screen		en Position max. (top)
Diagonal image size* (S)	Min. ceiling height**	Image width (w)	Image height (h)	Min. projection distance (a)	Sliderscale mark (b)	Distance from top of image to bottom wall plate holes (c)	Distance from top of image to temporary wall plate hole (d)	Distance from top of image to bottom wall plate holes (c)	Distance from top of image to temporary wall plate hole (d)
95"	93.5 87.3	37.4 3.9	-9 0.1	5.1 22.6 9.2	16.8
100"	96.2 91.9	39.4 4.6	-10.1	0.9 15.8 23.3	9.6 17.2
105"	98.9 96.5	41.4 5.4	-11.1	1.7 16.5 24.1	10.1 17.6
110"	101.6 10	1.1 43.3	6.2 - 12.2	2.4 17.3 24.8	10.5 18.1
115"	104.3 10	5.7 45.3	7 3.2	18		25.6 10.9 18.5
120"	107	110.3	47.3	7.8	1.5	18.7	26.3	11.4	18.9
125"	109.6 11	4.9 49.2	8.5	2.3	19.4 27.0 1	.8 19.3
130"	112.4 11	9.5 51.2	9.3	3.1	20.2 27.8 1	2.2 19.8
135"	113.5 12	1.3	52	10.1 3.4 20.5	28.0 12.3 19.9
140"	116.2 12	8.6 55.1	10	9 4.2 21.2 28	8.12.8 20.4
145"	118.8	133.2	57	11.7	5	21.9	29.5	13.2	20.7
150"	121.6	137 59	1	2.4 6.1 23.1	30.6 13.6 21.2
151"	122.1 13	8.7 59.4	12	6 6.3 23.2 30	8.13.7 21.3

* For images less than 99 inches, the projector's Tele settings must be used to reduce the image size. ** Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

Measurements in Centimeters for 21:9

						Default Screen Position		Screen Position max. (top)
Diagonal image size* (S)	Min. ceiling height**	Image width (w)	Image height (h)	Min. projection distance (a)	Sliderscale mark (b)	Distance from top of image to bottom wall plate holes (c)	Distance from top of image to temporary wall plate hole (d)	Distance from top of image to bottom wall plate holes (c)	Distance from top of image to temporary wall plate hole (d)
95"	237.6 22	1.8 95.1	35.3 -	48.4 0.2	38.3 57.5 23	4 42.7
100"	244.4	233.5	100.1	37.3 - 51.1	2.2	40.1	59.3	24.5	43.7
105"	251.3	245.1	105.1	39.3 - 53.8	4.2	42	61.2	25.6	44.8
110"	258.2	256.8	110.1	42.1 - 56.4	6.1	43.9	63.1	26.7	45.9
115"	265	268.5	115.1 4	3.2 8.1 45.7 6	4.9 27.2 46.9
120"	271.9 28	0.2 12	0.1 45.2	3.9 47.6 66.8	28.2 48.1
125"	278.7 29	1.8 12	5.1 47.2	5.9 49.4 68.6	29.2 49.1
130"	285.6	303.5	130.1	49.1	7.8	51.3	70.5	31	50.2
135"	292.4	315.2	135.1	51.1	9.8	53.1	72.3	32	51.2
140"	299.3	326.8	140.1	53.1	11.8	55	74.2	33.1	52.3
145"	228.3 28	9.5 12	4.1 46.8	5.5 49.1 68.3	29.7 48.9
150"	284.2 30	1.2 12	9.1 48.7	7.4 50.9 70.1	30.7	50
151"	285.6	303.5	130.1	49.1	7.8	51.3	70.5	31	50.2

* For images less than 99 inches, the projector's Tele settings must be used to reduce the image size. ** Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

Measurements in Inches for 16:6

						Default Screen Position Screen		en Position max. (top)
Diagonal image size* (S)	Min. ceiling height**	Image width (w)	Image height (h)	Min. projection distance (a)	Sliderscale mark (b)	Distance from top of image to bottom wall plate holes (c)	Distance from top of image to temporary wall plate hole (d)	Distance from top of image to bottom wall plate holes (c)	Distance from top of image to temporary wall plate hole (d)
93"	91.1 87	1 32.7 3	8 0.1 17.4	4 24.9 9.2 16.8
95"	92.1 89	33.4 4.1	0.4 17.7	25.3 9.4 16.9
100"	94.7 93	6 35.1 4	9 1.2 18.6	26.1 9.8 17.4
105"	97.3 98	3 36.9 5	7 1.9 19.4	27 10.2 17.8
110"	99.9 103	3 38.6 6.5	2.8 20.3	27.9 10.7 18.2
115"	104.3	107.7	40.4 7.3	3.6 21.2 28.7	11.1 18.7
120"	105.2	112.4	42.1 8.1	1.9 22.1 29.6	11.6 19.1
125"	107.9	117 43.9		8.9 2.7	23 30.5	12 19.5
130"	110.4	121.7	45.6 9.7	3.5 23.8 31.4	12.4 20
135"	113.1	126.4	47.4	10.5	4.3	24.7	32.2	12.8	20.4
140"	115.8	131.1	49.2	11.3	5.1	25.6	33.1	13.3	20.8
145"	118.3	135.8	50.9	12	5.8	26.4	34	13.7	21.3
148"	119.9	138.6	52	12.5	6.3	26.9	34.5	13.9	21.5

* For images less than 99 inches, the projector's Tele settings must be used to reduce the image size. ** Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

Measurements in Centimeters for 16:6

						Default Screen Position Screen		en Position max. (top)
Diagonal image size* (S)	Min. ceiling height**	Image width (w)	Image height (h)	Min. projection distance (a)	Sliderscale mark (b)	Distance from top of image to bottom wall plate holes (c)	Distance from top of image to temporary wall plate hole (d)	Distance from top of image to bottom wall plate holes (c)	Distance from top of image to temporary wall plate hole (d)
93"	231.2	221.1	82.9	35.2	.1	44.1	63.3	23.4	42.6
95"	233.9	225.9	84.7	36	.9	45	64.2	23.8	43
100"	240.5	237.8	89.1	38	2.9	47.2	66.4	24.9	44.1
105"	247.2	249.7	93.6	40	4.9	49.4	68.6	26	45.2
110"	253.9	261.6	98.1	42.1	7	51.6	70.8	27.1	46.3
115"	260.5	273.5	102.5	44.1	9	53.8	73	28.2	47.4
120"	267.5	285.3	107.2	46.1	4.8	56.1	75.3	29.3	48.6
125"	273.9	297.2	111.4	48.1	6.8	58.3	77.5	30.4	49.6
130"	280.6	309.1	115.9	50.1	8.8	60.5	79.7	31.5	50.7
135"	287.3	321	120.4	52.1	10.8	62.7	81.9	32.6	51.8
140"	293.9	332.9	124.8	54.1	12.8	64.9	84.1	33.7	52.9
145"	300.6	344.8	129.3	56.1	14.8	67.1	86.3	34.8	54
148"	304.5	351.9	131.9	57.3	16	68.4	87.6	35.4	54.6

* For images less than 99 inches, the projector's Tele settings must be used to reduce the image size. ** Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.

Make sure to follow the steps below to install the wall mount. If you ignore these steps, the wall mount could fall and cause personal injury or property damage.

Warning

☐ When you mount the projector on the wall with the wall mount, the wall requires enough strength to hold the projector and the wall mount. This wall mount should be installed on a concrete wall. Confirm the weight of the projector and the wall mount before installation, and maintain the strength of the wall. If the wall is not strong enough, reinforce the wall before installation. The maximum combined weight of the projector and the wall mount is about 48.5 lb (22 kg). ☐ Do not hang cables over the wall mount. ☐ Install the wall mount so that it can sufficiently support the weight of the projector and wall mount, and resist any horizontal vibration. Use M10 or 3/8 inch nuts and bolts and make sure to use appropriate wall anchors for your wall type. Nuts and bolts smaller than M10 or 3/8 inch could cause the wall mount to fall. ☐ Epson accepts no responsibility for any damage or injury caused by lack of wall strength or inadequate installation.

Assemble the parts

1. Assemble the wall plate.

Assemble the wall plate and two frames into one unit, and secure them with the M4 × 12 mm hexagon socket head cap bolts (×5) supplied.

1. Align the 3-axis adjustment unit with the slide plate's alignment mark.

If the 3-axis adjustment unit is not aligned, loosen the M4 × 12 mm hexagon socket head cap bolt (①) and correct the alignment (②) then, tighten the M4 × 12 mm hexagon socket head cap bolt.

1. Attach the 3-axis adjustment unit and slide plate to the projector.

Attach the 3-axis adjustment unit and slide plate to the projector using the M4 × 12 mm hexagon socket head cap bolts (×4) supplied.

Remove the feet from the projector and then attach the rubber caps to the front foot section.

Install the wall plate on the wall

1. Determine the template sheet position and attach it to the wall.
2. Confirm where the beams or studs are within the wall that can support the projector and wall mount.
3. From the projection distance table, confirm the screen size (S), the distance between the projection image and wall plate bottom holes (c), and the distance between the projection image and temporary wall plate hole (d).
4. Align the center position of the screen being projected with Image Center A on the Template sheet.

If you want to hide the projector power plug under the wall plate cover, make sure the power outlet is located in the empty space to the left or the right of the wall plate.

1. Drive an M10 screw (not included) into the temporary wall plate hole.

Leave at least 0.2 inch (6 mm) between the screw head and the wall.

1. Determine the position of the wall plate's mounting holes.

Use at least four mounting holes at the top, bottom, left, and right for proper balance.

1. Drill holes of the following diameters and depths.

Drill diameter	3/8 inch anchor bolts: 0.39 in. (10 mm)M10 anchor bolts: 0.41 in. (10.5 mm)
Pilot hole depth 1.8 in. (45 mm)
Anchor hole depth 1.6 in. (40 mm)

When routing cables to the projector through a wall, you can drill routing holes within the areas shown below. When installing a mini PC, check the position at which the mini PC plate will be installed before drilling the cable routing holes.

1. Remove the template sheet.
2. If necessary, use a device such as a dust pump to clean out concrete dust from the hole.

1. Position the wall plate on the temporary wall plate screw.

1. Insert commercially available M10 × 60 mm or 3/8 inch anchors into the holes and secure them in place.

Determine the projection distance and pull out the mount arm slider

1. Using the tables on pages 20 to 24, check the number for the slider measure (b).
2. Loosen the M4 × 12 mm hexagon socket head cap bolts (×2), and then pull out the slider on the arm unit.

Adjust the slider to the value that is equal to the slider measure (b) plus the thickness of the projection screen (x).

For an illustration of how to measure the thickness of the projection screen (x), see page 18.

④ Attach the arm unit to the wall plate

1. Insert the hexagonal shaft into the arm unit (①).
2. Insert and turn the hexagonal shaft at the top of the arm unit (②).

Make sure that cable ports for connecting to peripheral devices such as mini PCs are routed so that they come out of the lower part of the arm unit and not through walls.

1. Route the cables through the arm unit.

Caution

☐ Do not hang the rest of the cables over the arm unit. They could fall and cause an accident.

1. Insert the hexagonal shaft into the slot at the top of the wall plate (①). Insert the hexagonal shaft into the slot at the bottom of the wall plate (②).

1. Secure the mount arm to the wall plate by tightening the supplied M6 × 20 mm cross recessed head shoulder screws (×3) with the #3 cross-head screwdriver.

Make sure you use the included plastic washers. If you don't use the plastic washers, you may damage the M8 hexagon bolt as you adjust the vertical slide position.

Adjust the vertical slide position of the arm

1. Adjust the vertical slide with the hexagonal shaft at the bottom of the wall mount (①). Start by aligning the notch on the arm with the alignment mark on the wall plate as shown below (②). Tightening the hexagonal shaft raises the wall mount, and loosening the shaft lowers it (①).

1. Secure the wall mount with the M6 × 20 mm hexagon shoulder bolt.

Attach the projector to the wall mount

Attach the 3-axis adjustment unit with the projector to the wall mount arm:

- Mount at the stamp when the image is less than 117 inches diagonally.

- Mount at the stamp when the image is 117 inches or more diagonally.

- Tighten the M4 × 12 mm hexagon socket head cap bolts (×4) supplied to attach the 3-axis adjustment unit.

Warning

When installing or adjusting the wall mount, do not use adhesives to prevent the screws from loosening and do not use lubricants or oils on the projector slide plate. This may cause the case to crack and the projector to fall, resulting in personal injury or property damage.

Attach a Mini PC or Stick PC if necessary

You can secure a Mini PC or Stick PC to the left or the right side of the wall plate.

Attach the Mini PC so that the air exhaust vents of the PC are not blocked. Install the PC so that the air exhaust vents are at the top and the air intake vents are at the bottom.

If your Mini PC has screw holes that line up with the holes in the Mini PC plate, you can secure it with the M3 × 6 mm screws (×4) supplied.

If your Mini PC does not have screw holes or they do not line up with the holes on the Mini PC plate, you can secure it with the included Mini PC band.

1. Wrap the band around the Mini PC plate.

1. Secure the Mini PC plate to the wall plate using the M3 × 6 mm screws (×4) supplied.

1. Rest the PC on the lip of the Mini PC plate and secure it with the band.

To ensure the best image quality, follow the steps below to adjust the projected image.

The initial setup wizard is displayed when you turn on the projector for the first time. Use the up, down, left, right, and [Enter] buttons to set the Projection, Language, and Date & Time. Continue to adjust the shape and position of the projected image, as necessary. If necessary, you can then enable Quick Startup to speed up the projector's startup. Enabling this setting increases the power consumed during standby.

☐ Images are not stable immediately after turning on the projector. After starting projection, wait for at least 30 minutes before adjusting the image. ☐ Install and adjust the projector at a room temperature that is close to the actual intended usage environment. If the temperature changes, the position of the image may shift. ☐ When setting up multiple projectors using the batch setup function, perform the batch setup before adjusting the projected image. ☐ We recommend using the mechanical position adjustment on the mount to achieve the best image quality.

Display the Setting Plate Installation Guide

1. Press the power button on the remote control or the projector.
2. If the image is upside down, hold down the A/V Mute button on the remote control for 5 to 10 seconds. The image disappears briefly and reappears flipped top-to-bottom.
3. Press the [Menu] button on the remote control or control panel.

Remote Control Control Panel

1. Select Installation.
2. Select Setting Plate Installation Guide.

Use adjustment dial 1 on the left side to adjust the horizontal roll

Repeat steps ② to ⑦ as necessary.

Loosen the lower adjustment dial ( ) to adjust the horizontal roll.

Use adjustment dial 2 on the top to adjust the horizontal rotation

Loosen the M4 screw, and then turn the adjustment dial (②) to adjust the horizontal rotation.

Use adjustment dial 3 on the front to adjust the vertical tilt.

Loosen the lower adjustment dial to adjust the vertical tilt.

B A

Adjust the horizontal slide.

1. Loosen the M4 × 12 mm hexagon socket head cap bolt (①).
2. Adjust the slider for the slide plate (②).

Adjust the forward/backward slide.

1. Loosen the M4 × 12 mm hexagon socket head cap bolts (×2) (①).
2. Adjust the slider for the wall mount (②).

A

Adjust the vertical slide.

1. Loosen the M6 × 20 mm hexagon shoulder bolt (①).
2. Adjust the vertical slide using the hexagonal shaft at the bottom of the wall mount (②). Tightening the hexagonal shaft raises the wall mount, and loosening the shaft lowers it.

1. After you finish making all of the adjustments in steps ② to ⑦, tighten the screws that were loosened in those steps.

② to ⑦, retighten all the screws and bolts

Adjust the focus

1. Remove the projector's side cover by sliding the side cover latch.

1. Raise or lower the focus lever to adjust the image.

1. Adjust the focus of position A.

1. After you finish making the adjustment, carefully replace the projector's side cover.

Press the [Esc] button on the remote or control panel to exit the guidance screen after adjusting.

Warning

Tighten all bolts and screws firmly. Otherwise, the projector or wall mount may fall and cause personal injury or property damage.

Attach the wall plate cover and end cap

If you need to use a security cable, make sure you attach it before installing the wall plate cover. See page 49 for instructions.

1. Attach the left wall plate cover.

1. Attach the right wall plate cover.

1. Attach the end cap to the arm unit.

1. If you want to cover the groove in the arm unit, attach the masking sticker as shown.

Caution

Only a specialist should remove or reinstall the projector, including for maintenance and repairs. Refer to your online User's Guide for your projector for instructions on maintenance and repairs.

Making Screen Adjustments

Before performing the adjustments, set the Screen Type and the Screen Position setting. If you change the Screen Type or the Screen Position after making corrections, the corrections will be reset.

You can save adjusted values in Memory from the Geometry Correction menu.

Epson Setting Assistant app

To correct distortion more easily, you can use the Epson Setting Assistant app on a smartphone or tablet that has a camera function. You can download it from the Apple App Store or Google Play Store.

1. Download and install the app on your smartphone or tablet.
2. Press the [Menu] button on the remote control or control panel.

Remote Control Control Panel

1. Select Installation, and then select Connect to Setting Assistant. A QR code is displayed.
2. Use your smartphone or tablet to scan the QR code and then follow the instructions in the app.

Correcting the Image Shape on a Curved Surface

If you are projecting on a curved screen, adjust the Arc Correction setting to correct the image shape.

1. Press the [Menu] button on the remote control or control panel.

Remote Control Control Panel

1. Select Installation.

3. Select Geometry Correction.

4. Select Arc Correction.

5. Select the area that you want to correct.

1. Use the arrow buttons on the remote control or control panel to change the shape of the selected area.
2. Repeat steps 5 and 6 to adjust any additional areas.

Correcting the Corner Shape

You can adjust the shape of the image corners with the Quick Corner setting.

1. Press the [Menu] button on the remote control or control panel.

Remote Control Control Panel

1. Select Installation.
2. Select Geometry Correction.

1. Select Quick Corner.

1. Select the corner that you want to correct.

1. Use the arrow buttons on the remote control or control panel to change the shape of the selected corner.
2. Repeat steps 5 and 6 to adjust any additional corners.

Correcting the Image Shape at Individual Points

You can adjust the image at specific points with the Point Correction setting.

1. Press the [Menu] button on the remote control or control panel.

Remote Control Control Panel

1. Select Installation.
2. Select Geometry Correction.

1. Select Point Correction.

1. Select the point on the grid that you want to correct.

1. Use the arrow buttons on the remote control or control panel to change the shape of the selected point.

1. Repeat steps 5 and 6 to adjust any additional areas.

Attaching a Security Cable

If the projector is installed in a room where it will be left unattended, you can use a commercially available theft-prevention cable to secure the projector to a post or other object to prevent someone from taking it.

Remove the security cable installation point cover, and then attach the cable to the security cable installation point on the projector.

You can attach the security cable installation point cover to the back of the side cover so that it does not get lost.

For details on how to configure the cable, refer to the documentation supplied with the cable.

If applicable, make sure you leave the remote control and batteries in the room with the projector. The accessories included with the projector vary by model and region.

Attaching a Safety Wire

1. Use the clamp (①) to attach the carabiner and safety wire to the bottom of the projector and tighten the carabiner (②).

1. Place the projector into the arm unit and tighten the screws.

1. Attach the other carabiner (③) to the hole (④) in the arm section of the arm unit and pass the safety wire (⑤) through it before tightening the carabiner.

EPSON® is a registered trademark and the EPSON logo is a registered logomark of Seiko Epson Corporation.

App Store is a trademark of Apple Inc., registered in the U.S. and other countries.

Google® is a registered trademark and Google Play™ is a trademark of Google LLC.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

© 2023 Epson America, Inc., 9/23

CPD-63742

Projector Mounting Templates

For accurate placement, you must print these sheets at full size; do not reduce or enlarge.

Select a mounting template option below

Full Size Single Sheet Template

Requires a wide-carriage printer.

Segmented Template

For printing on 3-letter-sized pages

For accurate placement, you must print these sheets at full size. Do not reduce or enlarge. If you are using Adobe® Reader®, make sure Page Scaling is set to None and Auto-Rotate and Center is selected.

Trim the left and right sides of the sheets as needed, then carefully align the sheets before taping them together.

ELPMB62

CPD-58199 (letter)

9/19

Template sheet

Model sheet

Template

Template sheet

Template sheet

Template sheet

Template sheet

Template sheet

Template sheet

For North American Users:

www.epson.com/support/ustinstallation

EN

This manual explains how to handle wall mounts and provides an overview of installation procedures.

See the "Installation Guide" that you can access using the QR code on the right for more details.

epson.sn

Using the Product Safely

[SGGZ] Warning

The Wall mount is exclusively for mounting the projector on a wall. If anything other than a projector is mounted, the weight may result in damage.If this product falls, it could cause death or personal injury.

The installation work (wall mounting) should be performed by specialists who have technical knowledge and ability. Incomplete or incorrect installation could cause the product to fall and cause personal injury or property damage.

When installing this product on a wall, the wall requires enough strength to hold the projector and the wall mount.Ensure the strength of the wall before mounting this product on the wall.If the wall is not strong enough, reinforce the wall before installation.

Do not use adhesives, lubricants, or oils to install or adjust the Setting plate.Do not install in a location subject to oily smoke or smoke for events.If oils and so on stick to the slide plate fixing part of the projector, the case may crack and cause the projector to fall, resulting in personal injury or property damage.

Do not disassemble or remodel this product.

Caution

Do not use excessive force when adjusting this product.This product may break, resulting in personal injury.

Specifications

Item	Specification
Setting plate mass	Approx. 9.5kg
Maximum load capacity	Approx. 15.0kg