AN935H - Stapler MAKITA - Free user manual and instructions
Find the device manual for free AN935H MAKITA in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Pneumatic stapler |
| Brand | Makita |
| Model | AN935H |
| Dimensions (L x W x H) | 250 x 80 x 200 mm |
| Weight | 1.2 kg |
| Power Source | Compressed air (pressure 70-120 psi) |
| Air consumption | 0.1 m³/min |
| Magazine capacity | 100 staples |
| Compatible staple type | 18-gauge wire staples, length 10-16 mm |
| Firing rate | 30 staples/min |
| Cordless operation | No (requires compressor) |
| Maintenance | Regular lubrication with pneumatic oil |
| Cleaning | Clean deposits with a dry cloth |
| Safety | Safety trigger, sequential contact, anti-recoil system |
| Spare parts | Available online or at Makita authorized dealers |
| Repairability | Repairability score: 8.2/10 (estimate) |
| Warranty | Manufacturer's warranty 1 year |
Frequently Asked Questions - AN935H MAKITA
How to use the AN935H stapler?
First, make sure the air compressor is set between 70 and 120 psi. Load the staples into the magazine by pushing the strip all the way in. Place the tool against the surface, press the safety trigger then the main trigger to fire. Release after each shot.
What compressed air pressure is needed?
The recommended pressure is 70 to 120 psi (approximately 4.8 to 8.3 bar). Too low pressure can cause fastening defects, too high pressure may damage the tool.
How to load staples?
Open the magazine by pulling the slider. Insert a strip of staples into the groove, points facing forward. Push until it clicks. Close the magazine. Verify that the staples are properly aligned before use.
How to lubricate the tool?
Use a light pneumatic oil (ISO VG 32). Apply 2–3 drops into the air inlet fitting before each use. If the tool is used intensively, lubricate every 2 hours. This extends the life of seals.
What to do if the stapler does not fire?
First check the air supply: correct pressure and properly connected fitting. Then, clean the magazine of staple residue. If that doesn't work, disassemble the nose to remove a jammed staple. Refer to the exploded diagram in the manual appendix.
How to adjust the penetration depth?
Turn the adjustment knob located at the front of the tool. Turn clockwise to increase depth, counter-clockwise to decrease. Test on a scrap piece of wood before final use.
What types of staples are compatible?
The AN935H accepts 18-gauge wire staples (1.25 mm diameter) with a length of 10 to 16 mm. Use Makita brand staples or equivalent quality. Staples that are too long may damage the tool.
How to clean the stapler?
Disconnect the tool from the compressor. Use a dry, lint-free cloth to wipe off dust and residue. Do not use solvents or abrasive products. Clean the magazine with low-pressure compressed air.
Can the AN935H be used with other gases?
No, the tool is designed only for compressed air. Use of other gases (nitrogen, CO2) can be dangerous and void the warranty. Follow the specifications in the manual.
Where to find spare parts?
Spare parts are available on the official Makita website or at authorized dealers. Use the model number AN935H to identify compatible parts. Refer to the exploded view in the manual for exact references.
User questions about AN935H MAKITA
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Stapler in PDF format for free! Find your manual AN935H - MAKITA and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. AN935H by MAKITA.
USER MANUAL AN935H MAKITA
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : MAKITA
Model : AN935H
Category : Stapler