Professional 2 Boiler Pid - Coffee machine ISOMAC - Free user manual and instructions
Find the device manual for free Professional 2 Boiler Pid ISOMAC in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Espresso Machine |
| Brand | Isomac |
| Model | Professional 2 Boiler PID |
| Dimensions (WxDxH) | 350 x 450 x 400 mm |
| Weight | 32 kg |
| Power Consumption | 2000 W |
| Voltage / Frequency | 220-240 V, 50/60 Hz |
| Water Tank Capacity | 2.5 L |
| Steam Boiler Capacity | 1.0 L |
| Brew Boiler Capacity | 0.6 L |
| Group Head | E61 |
| Pump Type | Rotary |
| PID Temperature Control | Yes |
| Boiler Material | Brass |
| Casing Material | Stainless Steel |
| Pressure Gauge | Yes |
| Water Level Indicator | Yes |
| Drip Tray | Removable |
| Cup Warmer | Yes |
| Accessories Included | Portafilters, tamper, cleaning tools |
| Warranty | 2 years |
Frequently Asked Questions - Professional 2 Boiler Pid ISOMAC
How do I turn on the Isomac Professional 2 Boiler PID?
Plug the machine into a grounded outlet and flip the main power switch located on the rear or side panel. Wait for the boilers to reach the set temperature (indicated by the PID display).
How to adjust the PID temperature?
Press and hold the PID button for a few seconds to enter the settings menu. Use the up/down arrows to adjust the brew boiler temperature. Confirm by pressing the button again.
How often should I descale the machine?
Descaling is recommended every 2 to 3 months, depending on your water hardness. Use a descaling solution suitable for espresso machines and follow the manual's procedure.
What water hardness is recommended?
Use soft to medium-hard water (50–150 ppm). Avoid distilled or very hard water to prevent scale buildup and ensure optimal taste.
How to clean the group head?
Perform a backflush weekly using a blind basket and a cleaning detergent designed for espresso machines. Run the cycle as described in the manual, then rinse with fresh water.
Why is there no steam coming out?
Ensure the steam boiler is powered and has reached temperature. Check that the water level is sufficient and the steam wand is not blocked. If the issue persists, inspect the steam boiler thermostat.
How to set pre-infusion?
The pre-infusion duration can be adjusted via the PID menu. Access the settings and look for the pre-infusion parameter (usually 'PI'). Set a time between 2–5 seconds for best extraction.
Can I use pre-ground coffee?
Yes, you can use pre-ground coffee. Use a single-dose funnel to avoid mess and ensure even distribution. Adjust grind size if necessary for proper extraction.
How to replace the group head seals?
Turn off the machine, remove the shower screen and gasket. Replace with original Isomac seals (sized 72 mm). Reassemble and tighten gently to avoid damage.
What do error codes on the display mean?
Error codes vary by model. Common ones: E1 (temperature sensor failure), E2 (boiler overheat). Refer to the manual's troubleshooting section for specific codes and reset procedures.
User questions about Professional 2 Boiler Pid ISOMAC
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Coffee machine in PDF format for free! Find your manual Professional 2 Boiler Pid - ISOMAC and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Professional 2 Boiler Pid by ISOMAC.
USER MANUAL Professional 2 Boiler Pid ISOMAC
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : ISOMAC
Model : Professional 2 Boiler Pid
Category : Coffee machine