H190v - Receiver Hegel - Free user manual and instructions
Find the device manual for free H190v Hegel in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Integrated Amplifier / Receiver |
| Brand | Hegel |
| Model | H190v |
| Power Output | 2 x 150W into 8 ohms |
| Frequency Response | 5 Hz - 100 kHz |
| Signal-to-Noise Ratio | > 100 dB |
| Digital Inputs | 1 x Coaxial, 2 x Optical, 1 x USB |
| Analog Inputs | 1 x XLR, 2 x RCA, 1 x Phono (MM) |
| Preamp Output | 1 x RCA, 1 x XLR |
| Speaker Outputs | Bi-wireable binding posts |
| Headphone Output | 6.3 mm jack |
| DAC | High-performance DAC with up to 24-bit/192 kHz |
| Amplifier Technology | Hegel DualAmp and SoundEngine2 |
| Remote Control | Included |
| Dimensions (W x H x D) | 430 x 110 x 380 mm |
| Weight | 15 kg |
| Power Consumption | 500 W max, < 0.5 W standby |
| Mains Voltage | 220-240 V or 110-120 V (depending on region) |
| Maintenance | Clean with a dry, soft cloth. Do not use solvents. |
| Safety Precautions | Do not expose to moisture or heat. Ensure adequate ventilation. Unplug during storms. |
| Spare Parts & Repairs | Contact authorized Hegel service center |
Frequently Asked Questions - H190v Hegel
How do I connect the H190v to my TV?
Use the optical or coaxial digital input. Connect the TV's digital audio output to the corresponding input on the H190v. Select the correct input source on the amplifier.
Can I use the H190v as a preamp only?
Yes, the H190v has preamp outputs (RCA and XLR) that can be used to connect to an external power amplifier.
What is the maximum resolution for the USB DAC?
The USB input supports up to 24-bit/192 kHz PCM audio. It does not support DSD natively.
How do I reset the H190v to factory settings?
Turn off the unit, then press and hold the 'Menu' button while turning it on. Continue holding until 'Factory Reset' appears on the display. Use the volume knob to confirm.
Does the H190v have a phono input?
Yes, it has a dedicated phono input for MM (moving magnet) turntables.
What is the recommended speaker impedance?
The H190v is stable with speakers from 4 to 8 ohms. For 4-ohm speakers, ensure proper ventilation as the amplifier will work harder.
How do I update the firmware?
Firmware updates are not user-serviceable. Contact Hegel support or an authorized dealer for assistance.
The amplifier shuts down after a few minutes. What could be wrong?
This may indicate overheating or a speaker short circuit. Check speaker connections and ensure adequate ventilation. If the problem persists, contact service.
Can I bi-wire speakers with the H190v?
Yes, the speaker terminals allow bi-wiring. Remove the jumpers on the speakers and connect separate cables to the high and low frequency terminals.
Does the H190v support Bluetooth?
No, the H190v does not have built-in Bluetooth. You can add a Bluetooth receiver to an analog input.
User questions about H190v Hegel
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual H190v - Hegel and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. H190v by Hegel.
USER MANUAL H190v Hegel
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Hegel
Model : H190v
Category : Receiver