SRT 8113 - Satellite receiver STRONG - Free user manual and instructions

USER MANUAL SRT 8113 STRONG

PART 1 English <STRON.

1.1 Safety Instructions 2

22 Front Panel 3 23 Rear Panel 4 24 Remote Control 4

3.1 Connecting to a Terrestrial Antenna 5

322 Connecting to TV with HDMI cable 5 33 Connecting to TV with SCART cable 5 34 Connecting to a Digital Audio Amplfier with S/PDIF 5 35 Connecting to a Digital Audio Ampifie and TV using HDMI 6 346 Connecting a USB storage device 6 37 Connecting to a TV using modulator output 6

4.0 STARTING UP FOR THE FIRST TIME 6

5.0 QUICK GUIDE FOR USING YOUR RECEIVER 7

6.1 Changing channels 7

621nfo Banner 8 63 Selection of audio language 8

1.1 Safety Instructions

DO NOT INSTALL YOUR RECEIVER: =. Ina closed or poory ventilated cabinet directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots. DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: = To diectsunlight or any other equipment that generates heat to rain orintense moisture;to intense vibration and to any shock which may cause permanent damage to your tecever or any magnetic objects, such as loudspeakers,transfomners et Do not use a damaged power cord. may cause a fire oran electric shock Do not touch a pouer cord et hands. may cause an electric shock. Mnen the receveris not used for long period oftime, you should unplug the power cord'iom thewal socket. Do nat use alcohol or ammonia based ques to clean the receiver you wish, you may clean yourrecevervith a soft intra cloth sighty made damp uit a mid 0 solution, and only after isconnecting from the mains voltage suppy. Make sure no foreign objects al hroughthe ventiation slots because this could cause fre oran elec shock Do nat place any objects an top ofthe receive because his might prevent proper cooling ofthe components inside. Safety Precautions = Never try to open the receiver.Iis dangerous to touch the inside ofthe receiver due to High voltages and possible electrical hazards, Opening the receiver will void the warranty of the product Referall maintenance ar sevicing to suitably qualfied personnel. = When you are connecting cables, be sure that the receiveris disconnected from the mains supply voltage. Wait a few seconds after witching of the receiver before you move the receiver or disconnect any equipment. = is a necessity that you only use an approved extension and compatible wiring that is suitable for the electrical power consumption of the installed equipment. Please ensure that the electrical power supply correspond with the voltage on the electrical identification plate at the back ofthe receiver. Ithe receiver does not operate normally even after strict} following the instructions in this user manual is recommended to consult your dealer.

Yourreceiver and it accessories are stored and delveredin a packaging designed to protect against electric shocks and moisture. When unpacking f, make sure that al the pars are included and keep the packaging away from children. Wen transporing {he receiver from one place to another or ifyouare returing itunder varranty conditions, make sure to repackthe receiverin its original packaging with its accessories Faling to comply with such packaging procedures could damage the product and void your warranty.

PART 1 English <STRON.

1.3 Equipment Set-up

We recommend you consult a professional installer to set up your equipment. Othenvise, please follow the instructions belour # Referto the user manual of your TV and antenna. = Make sure that the HDMI cable and outdoor components rein a good condition = Ifyouuse TV SCART connection use then well shielded SCART cable. This manual provides complet instructions foristaling and using this receiver. The following symbol will serve as follur.

WARNING: Indicates vaming information.

Tips Indicates any other additional important or helpful information. MENU Represents a button on the remote control or the receiver. (Bold Character) Moveto Represents a menu tem within a window. talic Character)

= User manual = _ remote control unit w_2xbatteries (AAA type) = Male/Female antenna cable = active indoor antenna with cable NOTE: ‘The batteries should not be recharged, disassembled, electrically short drcuited, be mixed or used with other types of batteries.

1.5 Usage of external USB devices

= lis recommended to use USB 20 storage devices orhigher. your device is not compatible to USB 20 speciications, recording, playback and other multimedia functions ofthe receiver might not work proper}. To ensure best performance of your USB storage device please format t by this receiver (menu “Media, DVR Storage Information’) to FAT32 system. Other le systems are not supported by the receiver. However, is possible to use already NTFS formatted disks, STRONG cannot guarantee compatiblity with al types of USB storage devices. Ii advised not to store important information on USB storage devices used with the recciver. Aays make backups of data on your USB storage device before using itwith this receiver. STRONG wil not take responsibility for any los ofinformation or circumstances caused by loss ofinformation.

1. Modeindicator | RED'indicates thatthe receiver sin STANDBY mode.

(GREEN indicates that the receiver is in OPERATING mode. www.strongtv

2. IRsensor Point your remote control towards this sensor.

3. uss “Connector for USB devices.

1. ANTIN To connect to your antenna for the reception of broadcast signal.

2 ANTOUT To connect tothe terrestral antenna input of your TV set. ‘This connection will allow you to watch analogue terestrial programmes ifthey are available via the tuner in your TV.

3. TO To connect to a TV using a coaxial cable. This connection

{modulator) wil allow you to watch channels from this receiver ‘on an UHF channel on your TV.

4. SIPDIF To connect your receiver to a digital audio amplifier.

S. HDMI To connect your receiver with your TV set using a HDMI cable. 6 TVSCART | Toconnect yourrecewerwith your TV set using a SCART cable.

7. PowerCord | Vourreceverrequires a voltage of 220-240V AC (Auto-

selectable), 50/60 Hz +/-5%. Check the local power specfication before connecting your recever to the walloutlet.

Fig.3 1 © Tumsthe recciver On/Standby 2 INFO Shows the current channel information

3. SLEEP Tums the receiverto Standby after time selection

a Mutes audio output ofthe receiver 5 4 Fastrewind 6 » Fast forward

1. PGHPG- ‘Channel up/domm in channel ist mode

20. AUDIO Setsthe current audio channel to lefright or stereo

21. SUB Shous is of subttied languages

2 mx Shows Teletext on O$D (On Screen Display) 4 wwwsstrongtv

PART 1 English <STRON.

25. TIMESHIFTAI Star Timeshiftmode orpause

2. m Stop of phyback

PA Start Records the TV programme to the connected storage device

28. 200M To 00m in to the video on screen

29. ASPECT Change aspect modes: 43 LB, 43PS, 169 andto Auto.

30. V-FORMAT Change video resolution modes: 480 up to 1080p

32. Colouredbuttons Multimedia and Teletex functions

3.1 Connecting to a Terrestrial Antenna

Fig.4 Toreceive broadcast signal, your terrestral indoor antenna must be connected to the ANT IN connector on the back ofthe receiver. The ANT OUT connector allows you to loop the antenna signal to a second receiver or TV set. NOTE: Ithe signals at your location are too weak to receive proper signals with the induded indoor antenna, we recommend using an outdoor antenna which an be pointed to transmission tower. Ask your local dealer for more advice.

3.2 Connecting to TV with HDMI cable

Fig.4 The TV set shall be connected with the receiverusing a goocl quality HDMI cable. This connection gives the highest possible quality

3.3 Connecting to TV with SCART cable

Fig.4 SRT 8113is also equipped with a SCART connector altemativehy, the TV set can be connected to the receiverusing a good quality SCART cable.

3.4 Connecting to a Digital Audio Amplifier with S/PDIF

Fig.5 By connecting your receiver to a digital amplifier or home theatre system, you can enjoy the best possible sound quality and mult-channel audio (depending on broadcast. Connect your Digital Audio Amplifier or home theatre system with a suitable cinch cable to the S/PDIF connector on the back ofthe receive. www.strongtv 5

<STRONG PAT gl DIEMALI r and TV using Fig.s By connecting your receiver ta the latest digital amplfiers or Home Cinema systems you will enjoy the best possible sound quality and mult-channel audio (depending on broadcasd. Connect the HDMI output of the receiver to an input of your amplifier, and then connect the HDMI output of the amplifier to your TV set. Select the correct input on your amplifier to watch and listen to programmes.

3.6 Connecting a USB storage device

Fig.6 NOTE: We recommend the use of a hard disk drive USB 20 or higher far recording and play back oFTV events. For proper functioning of Timeshif and recording functions a fast USB device {such as a hard disk ve) is needed. Inteupted playback or distorted pictures during playback or Timeshft are indications for low device specd, STRONG cannot guarantee proper functioning ofrecoding and or Timeshif functions with ll USB devices.

3.7 Connecting to a TV using modulator output

Fig.4 To view a TV channel on your TV (or a TV setin another room) altemativey you can use the UHF analogue modulator output TO TV) and connect it with a coaxial cable to the (other) TV set. You must letthe (other) TV set search or scan forthe RF signal out ofthe modulator.(Refer to the manual of your TVset) Defauft channel is 38, PAL-B6, but is adjustable in the System setup menu in the TV system. Choose a channel which is not occupied by TV transmittrs in your region to avoid interference. Please note, when other connection options are available on your TV set those are preferable.

4.0 STARTING UP FOR THE FIRST TIME

Hyouuse your receiver for the frs time, the Welcome “Easy install menu appears. Use À V to move the highlight to the setting you wish to alter and use 4 D to change values. Start by selecting your language using 4 D. Once you have selected your language, press V to move the highlight to the next item and use 4 D to change. Language Select your language. Region: Select our region where this recever is used. Video Resolution: Use this option to select the video resolution of your TV screen. Press OK to callalistwith all possible resolutions. The options are: By Source (automatic detection of video resolution offered to the receiver) By Native TV [automatic detection of maximal resolution of TV screen) and manual selections 480), 576lup to 1080p Please use a setting that matches your TV specfications. After a selection is made, you will be asked to confim. Aspect Mode: Use this option to select the aspect ratio of your TV and the preferred conversion method. Options are: Auto (automatic detection of aspect ratio), 43 Panscan (Displeys 169 widescreen broadcastsful screen on your 43 TV), 43 etterbox (black bars on top and under the picture on a 43 TV) and 169 {use this setting for 169 TV sets). 6 wwwsstrongtv

PART 1 English <STRON.

DIGITAL TV Antenna Power. Setto On if you use an active antenna. When set to On, 5 Vwél be present ‘on the ANT IN connector ofthe receiver. Select Offfor passive antennes. The included antenna is a active type. Ifyou using this antenna keep selection t00n. NOTE: Wrong region selection can lead to missing channels or channels being stored on wrong positions in the channel ist A default selections above are mest common to use. Once all settings are made, move the highlight to OK press OK to start scanning. The receiver will now search for all available channels. Once scanning is finished, the receiver switches to viewing mode. TP: Ithe Welcome "Easy install’ menu does not appear after switching on the receiver the first time, reset the receiver to factory settings by pressing the MENU button and selecting Factory Setting in the submenu Tools. (Default PIN: 1234)

5.0 QUICK GUIDE FOR USING YOUR RECEIVER

We at STRONG understand that you can wait to enjoy your new high definition digital terrestral receiver. The following quick guide wil make you familar with the basic operation ofthis device. We do, however, advice you to read the full manual to get the best performance from your receiver. To turn your receiver ON or to Standby, use the À button on the remote control Choose the desired channel withthe A. buttons. Alternative, you can digit the channel number with the 0-9 buttons on the remote control Or press OK in viewing mode to display the channel ist. The volume can be adjusted with the 4 D buttons.

Your new receiveris equipped with several features to make watching TV a rue pleasure. This paragraph describes these features. Please also read chapter 7.0 to get familiar with the menu of your

6.1 Changing channels

Your ne receive is equipped with four ways to change channels. = Via direct access using the 0-9 buttons = Viathe channellisttrough OK button. = Viathe PG+ and PG- keys. = Viathe À V keys

6.1.1 Direct access via 0-9 buttons

To gain direct access to a certain channel, simply input is number with the 0-9 buttons onthe remote contral. Channel numbers can be up to four digits long. Entering a number with less than four digis is possible. Just wait a few seconds and your receiver will switch to the selected channel or press OK immediately after selecting the channel number. www.strongtv 7

Press OK in viewing mode to display the Channels Use À V in the Channel Listto highight yourchannel ofchoice nd press OK once t electthe highihted channel Press OK again to leve the Channels. La Use 4 to toggle between the Al Channels, ChannelListand favourite lisser press FAV for a ist of available Favourite ist.

6.1.3 Usingthe à v or PG+/PG-keys

À switches to thenext channel 3 switches to the previous channel PG+switches to the next 10 channels. PG-suitches to the previous 10 channels.

While watching TV you can press the INFO button any time to get information about the current channel and event. Press INFO twice for technical details about the current channeL I you have connected an USB device then it val also cal the Record st orTimeshift banner when you press the INFO button once more “Event information is displayed when available. Avalabiity depends on broadeast

6.3 Selection of audio language

Some channels support a choice of audio formats and/or languages. To select another audio stream, press AUDIO in viewing mode. A list with available au streams will nou be displayed. Use À W to select the desired stream and confirm with OK The audio channels stereo, mon, leftand right can be selected vith the 4 buttons,

Your receiverincludes a fuly featured Teletext. To access Teletex, press the TX button in vieuing mode and use the 0-9 buttons te input the number ofthe page you wish to see, The coloured buttons ofthe remote control allow you to jump ta selected pages direct, as indicated on the bottom ofthe teletex screen. Use the À V buttons to select one page up or down, use 4 > buttons to select subpages. Press EXIT or TTX to get back to viewing mode. NOTE: Hcharacters are not displayed correct} then check Ifyour Teletext language is setta the correct language. See chapter 7.4.1

Some channels support a choice of subtil languages. Press SUB in viewing mode to display a lis of avaïlble subtil languages. Select your subie of choice with À W and press OK to confim. Press EXIT to leave without making changes.

Timeshifr allows you to pause ve broadcasts and resume playback later. Connect your USB storage device and make sure that Timeshift is set to ON in the menu DVR Settings. Press TIMESHIFT/ 8 wwwsstrongtv

PART 1 English <STRON.

DIGITAL TV viewing mode to actvate this mode. On screen the time shift info banner appears Press to resume Timeshifted playback. Press 449} for fast rewind/fast forward. Press to return to live TV. NOTE: Timeshift needs 2 connected USB storage device with suffcient free space and sufcient speed in order to work properl.

6.7 EPG (Electronic Programme Guide)

The Electronic Programme Guide is a verÿ useful function that allows you to view event schedules and'information and to mark programmes for recording, To access the EPG, press the EPG button in viewing mode. Use À V toselect a channel and 4 D to select an event. Press OK to displey detailed information on the selected event. Use EXIT to quit the detalled information screen. Press RED to ‘gettothe Step Time function. Use 4 to select the desired step and OK to execute it. Press EXIT to quitthe Step Time function. Press GREEN t set a timer for selected event. Referto section 7.4.5 for detail en the timer function. NOTE: AAvailabilty of EPG data depends on broadcast.

6.8 Instant Recording

Your newrreceiver allows you te make an instant recording ofthe programme you are watching Simply press @ to start the recording. To enter the duration for the recording, press @ again. Use the 0-9 keys to input the desire recording time. During the star ofrecording a recording sign will be show on the upper right of your TV screen. To stop the recording, press BL. Select Ves and press OK again to stop the recording, NOTE: You can access the Record Manager direct via the button in viewing mode ta select a recording for playback

The main menu gives you access to settings, multimedia functions and in-built games. To access the main menu, press MENU in viewing mode. The main menu consists ofthe following sub menus: Media, di Channel Installation, System Setup and Took. Throughout the main menu, MENU or EXIT can be used to get backtothe previous screen.

‘The Media menu consists ofthe following submenus: Media Player, DVR Storage Information, DVR Settings and Games (Othello and Sudoku). Use À Y to highlight the menu of choice and press OK to “enter. Press EXIT to qui.

hisfuncton allows you to play MPEG, AVL MP3,1PG many other type files om connected storage device (see details in technical par. You can also playback music and images atthe same time. Select Media Player from the Media menu and press OK to proceed, When you enter media player window, the highlights on the USB/HDD device. www.strongtv

<STRONG PAT gl DIEMALI Use the MOSAIC button to select between DV, Video, Music or Image. Press the W buttonto move the highlighttathe directory and the flefild.Press OK to confim the selection. The help banner atthe bottom afthe screen explais al buttons used in the Media player.Press EXIT to quit or more times to exit. Press the “Red” Play Lit button to show the Play List. NOTE: This is only possible if 2 Play List has been created. GREEN. Move the highlight to the music fl that you want to add to the Play List then press the “Green' AV button to add it wil mark a favourite icon on the ile. YELLOW: Press the "Yellow FAV Al button to add al fles ofthe current directory to the play Hit Press again to delete al fles ofthe current directory from the playlist. BLUE. Press the “Blue” Edit button to enter the edit sub-menu You can Rename/Copy/Delete/Create a folder. NOTE: Press EXIT 2 x times to ext. 1 Press number 1 Repeat button to set the repeat mode. The option is Repeat Folder/Random Falder/Repeat One. Press OK to start the play mode. EXT: Return, Stop or one step back. Image: RED: Press the “Red” Play Lit button to show the Play List. NOTE: This is only possible ia Play List has been created. GREEN. Movethehighhght to the Image file that you went to add ta the Play List then press the “Green” FAV button to add wi mark a favourie icon on the file. YELLOW: Pressthe Yellow FAV AL button to add al fles ofthe curent directory to the play Hit Press again to delete al files ofthe current directory from the play st. BLUE. Press the “Blue” Edit button to enter the edit sub-menu You can Rename/Copy/Delete/Create a folder. NOTE: Press EXIT 2 x times to ext. 1 Press number button to open the Image setup. Here you can select time of Slide show and Repeat mode On or Of. 2 Press 2 MuliView button to view images in multi view mode Press OK to startthe play mode. EXT: Return, Stop or one step back. Video: BLUE. Press the “Blue” Edit button to enter the edit sub-menu You can Rename/Copy/Delete/Create Folder. 1 Press number 1 Repeat button to set the repeat mode. The option is Repeat Folder/Random Falder/Repeat One. Press OK to start the play mode. During the play mode you can use the AUDIO and SUB buttons to select other audio tracks or the way how subtites are displayed, available. Return, Stop or one step back. 10 wwwsstrongtv

PART 1 English <STRON.

DIGITAL TV DvR: RED: Press the “Red Rename button to open the rename window to rename a recording. GREEN Move the highlight to the programme that you want to lock When pressing the Green” Lock button, it will ask you to input password. The default password is "1234". Afer input of correct password, the programme is locked. Hfyou want to unlockthe programme, press the “Green” Lock button again. YELLOW: Move the highlight to the program me that you want to delete. When pressing the “Yellow” Delete button, will ask you to input password. The defaut password is "1234" After input of correct password, the programme is marked th a lock. Hyou want to unlockthe programme, press the “Yellow” Delete button again or press EXIT to delete the selected recording(s). EXT: Return, Stop, one step back or press OK to start play mode.

7.1.2 DVR Storage Information

‘This option shows relevant information about the connected USB storage device. Also you can format your USB storage device into FAT32. Select DVR Storage Information from the Media menu and press OK to enter. Now you will se all details as Free and used Recoding Sizes and used fle system. Press the YELLOW button Format menu to format the connected USB device. Please, enterthe PIN to access this menu and press OK to start formatting. Select Cancel or press EXIT to leave without formatting.

WARNING: Formatting will permanent delete ALL data stored on the connected device.

Please make a backup copy of all data you wish to keep before entering the Format menu. STRONG cannot be held responsible for loss of data from USB devices used with this receiver. NOTE: Ii possible to use already NTFS formatted USB disks. Press EXIT to leave.

‘The DVR Settings menu allows you to setup the Timeshif, Jump function for playbackand type recordings. Select DVR Settings from the Media menu and press OK to enter. Timeshif. On/Off Select On f you like to activate Timeshift by pressing the YELLOW button. Timeshift wil already start in the background direct}y after you tune into a channel. Select Offto disable Timeshif. The YELLOW button will now only freezethe TV screen. Jump: 305ec to 30 min. Set the time step you Ike to jump forward or backwards with he buttons or Kk during playback of recorded files, Timeshift to Record On/Off. Select On you ike to keep a copy ofthe last made Timeshif by pressing the @ button. Select Offto disable. PS Record On/Off Select On f you like to reduce recording data. The recording will not record TXT, extra Subtiles or Audio channels on SD channels. Select Ofto disable and ll data of recorded channel ill stored to the record. www.strongtv

<STRONG PAT gl DIEMALI Press EXIT to leave.

Your receiveris equipped with two games which can be played on your TV screen using the receive remote control. Select one ofthe available games (Othello or Sudoku) using A Y and press OK to start the game. Follow the directions on screen. Press EXIT to quit a game.

Use À Y to select Edit Channel and press OK or to enter. Use A V to highlight the submenu of choice and press OK to select Press EXIT or 4 to get back to the main menu,

7.2.1 TV Channel List

In Edit Channel menu select T/Channelistwith A. W and press OK to enter. Use 4 t0 change the channel group {assumed you have already set up favourite groups). Selectthe channel of choice with À Press OK to view the selected channel in the preview box.

7.2.1.1 Adding channels to favourite lists

Channels from the TV Channel List can be added to up to 8 different favorite groups.Press FAV whilein TV ChannelListto access this function. The FAV sign on the top ofthe screen will move up toindicate thatthe favourie function is selected. Use À Y to select a channel you wish to add to à favourite group. When the highlights on the channel of your choice, press OK. A list with all available favourit lists will now pop up. Use AY to select the Favourite list you wish to add the channel to and press OK, press EXIT to finalze the process. Favourite channels will be marked with a heart symbol. When all changes have been made, press EXIT twice, À confirmation banner will pop up. Select Yes to save the changes or No to discard. Locking channels Locked channels can on be watched after enteringthe pin code (DEFAULT PIN: 1234) Toleckor unlock channel press RED win TV/ChamnelList The red Q sign onthe top ofthe screenwil ave upto Indice thatthe Lock functionis selected. Use A W 1 select a channel and pres OKto lock orunlocki. You are asked t input the pin code. (DEFAULT PIN: 1234) Locked channels will be marked with the @ symbol. Locking/unlocking multiple channels in one session is possble.Wen al changes have been made, press EXIT tuice À confimation banner vil popup Selec est save the changes or Not discard

7.2.1.2 Skipping channels

Channels marked with Skpwil be skipped when zapping channels withthe À V buttons. The channels vil til be valable om the channels. To mark channels for skipping, press GREEN wi in TV Channel List The Skip symbol on the top of the screen will move up toindicate that the Skpfuncion is selected. Use À V t select a channel andpress OK to mark orunmarkit for shipping. Channels set for skpping il be marked th the 2 wwwsstrongtv

PART 1 English <STRON.

DIGITAL TV -— symbol. When al changes have been made, press EXIT twice, À confirmation banner will pop up. Select Yes to save the changes or No to discard.

7.2.1.3 Moving channels

To enable the Move function press YELLOW wii in TV Channel List. The Move symbol on the top of the screen wil move up to indicate thatthe Move function is selected. Use À W to select a channel and press OK to select. You can nou move the selected channel up or dou the channel list using ZA V.When the channels on the postion of your choice, press OK again, The channels now fixed on is new position. When all changes have been made, press EXIT tuice. À confimation banner will pop up. Select Ves to save the changes or No to discard.

7.2.1.4 Editing channels

The Édit function allows ou to $or, Rename or Delte channel. To enter the Edit menu, press BLUE wlein T/Chamnel Lit The Edit Channel menu vil appear. Iyoumade changes in the previous menu, butnot saved them yet, you vil be askedto do 50 now Sort Press RED to enter the Sortmenu. Use A Y to select sorting method and press OK to confirm. Possible methods are: Name (A2 Sorting in alphabetical order from À to Z. Name (ZA; Sorting in alphabetical order from Z to A. Free/Scramble: Firstin the ist wall be Free-To-Airchannek. Lock Allunlocked channels will be placed first in the ist. Defautt Sorting by searched Order (from lowest to highest frequency or by LCN numbering). Rename Press GREEN in Edit Channel to enable the Rename function, The Rename sign will move up to indicate that Rename is selected. Use À W to highlight a channel and press OK to select. À text field wilnow pop up atthe right ofthe screen. Use € A Y to select characters and enter them with ‘OK When you have finished editing, press BLUE to enter the changes. When al changes have been made, press EXIT twice. Select es to save the changes or No to discard. Delete Press BLUE in Edit Channel to enable the Delete function. The Delete sign wa move up to indicate that Deleteis selected. Use À V to highlight a channel and press OK to mark for deletion. When you have marked al channels you wish to delete, press EXIT twice. À confirmation banner will be displayed. Select Ves to delete the marked channels or No to cancel.

7.2.2 Radio Channel List

Basicall,the operation of the Radio Channel ist is the same as in the TV Channel List The only. difference is thatin Radio Channel Lis there is no video information, soit will always display the radio” logo atthe right preview screen. www.strongtv

Use this menu to delete al stored channel. Select Delete Allwith A. W and press OK The receiver asks you to enter the pin code. (DEFAULT PIN: 1234).In the confirmation window select Ves with 4 D and press OK to delete or select No to cancel

WARNING: ‘The Delete all function will permanentiy delete all current channels and all

favourit lists from your receiver, and you are not able to leave the menu until you search for channels again.

Use À Y toselect Installation, press OK or b to advance. Use À Y toselect Channel Scan and press OK to enter. Use 4 totoggle between available scan modes: By Channel and By Frege By Channels selected, use the cursor buttons to select Scan Band'and Channel No. By Frequency is selected, use the cursor buttons t select Frequency and Bandwidth. Highlight Search and press OK to Start scanning. Newy found channels wil be storedin the channel ist.

Use A Y to select Installation and press OK or to advance. Select Auto Scan with À Y and press OK to enter. Use 4 to toggle between FTA Onby es ar No. When FTA Onbyis setto Ves, scrambled channels wontt be stared in the channel list. Use À W to highlight Search. Now press OK to start auto scan. ‘The receiver il store all new found channels in the channel ist.

7.3.3 LCN (Logical Channel Numbering)

IFLCN (Logical Channel Numbering) acivated and an LCN signal is provided by the operator, channels il be stored in an operator defined order. Set LCN 0 On to activate operator defined channel numberng or Ofto store channel in found order.

Use this menu to setup Antenna Power, Power saving mode and usage of signal to Antenna loop out.

7.3.4.1 Antenna Power

Set to On if you use an active antenna. When set to On, 5 Volt with a maximum current of 50 mA well be present on the ANT IN connector ofthe receiver. Select Offfor passive antennas. The included antenna is an active type. you use this antenna, keep the selection to On.

7.3.4.2 Auto Standby

Auto Standby is new feature that helps you reducing power consumption. When set to On the receiverwil um to standby fit doesn receive any commands for three hours, Set Auto Sandy to Offto avoid the automatic switch dou. 14 wwwsstrongtv

PART 1 English <STRON.

Set this option to On if you connect a second receiver or TV to the loop out (ANT OUT) ofthis receiver. This wil allow passing antenna signal fthe receiver is in standby mode. To reduce power consumption is default set to Of. NOTE: ‘The Antenna Power supplies (5 Vol) switch offin standby mode. you are Using an active antenna then the option RF Loop in Standby is not usable

This menu allows you to manage the system setings of your receiver. I consists ofthe following sub-menus: Language, TV System, Display Setting, Local Time Setting, Timer Settng, Parental Lock, SD) Setting, Favourite ist Rename and Multivie Seting. Press À Y to highlight the menu of choice and press OK advance tothe next screen. Use À V to move the highlight to the setting of choice. Values can be changed with 4 >.Press EXIT to leave.

This menu allows you to setup your language preference. Language: Use 4 to select the language for the On Screen Display. Fist Audio Use 4 to sclect Audio language. Second Audio Use 4 to select a language that all be played when the language selected atfirst Audio isn't available. Tete: Use 4 to select the preferred teletex language {sien available}

Use this menu to match your receiver to your TV set. The following settings are available: Video fesoktion: Use this option selectthe video resolution of your TV screen. The options are: By Source (automatic detection of video resolution offered to the receive, By Native TV automatic detection of maximal resolution of TV screen) and manual selections 480,576 up to 1080. Please use a setting that matches your TV specfications. After a selection is made, you wil be asked to confim. Selection above 576 only applicable on HDMI output. Aspect Mode: Use this option to select the aspect ratio of your TV and the preferred conversion method. The options are: Auto (automatic detection of aspect ratio), 43 Panscan (Displays 169 videscreen broadcasts ful screen on your 43 TV), 43 letterbox (black bars on top and under the picture on a 43 TV) and 169 (use this setting for 169 TV sets) Video Ou. Use this option to select which video quality you ike to have on the TV SCART output Select CV8S or RGB for best quality. you using a HDMI cable then select CVBS, This selection allow you to select behind Video Resolution also the high resolutions up to 1080p. RFSystem: When using the TO TV connector on the rear panel (the builin RF modulator) you can select here your TV set analogue reception system. Default is PAL-8G. RF Channel Setthe RF channel ofthe modulator. Default is channel 38. www.strongtv 15

<STRONG PAT gl DIEMALI Digital Audio Output: Toggles between PCM and Bitstream output. When PCM is selected, all digital audio wil be converted to stereo audio. Bistream enables mult-channel audio on HDMI for use with a Home Cinema Set

7.433 Display Setting

Here you can setup and adjust your video output you do notlike the colour in the playback of some media les or you want t change the colours for the TV screen.

7.4.4 Local Time Setting

Here you can set up your region and time zone. Region: Use 4 to select the region you lvein. GMT Usage: Setto On far broadeaster defined time orto Oftoinputtime and date manual}. GMT Ofer AAllows you t adjustthe time zone you Iveir. This aptionis only available when GMT Usages set to On. The GMT Offet range is "11:30 — +12:00° increasing by half hours progressively. The cities matching the set GMT Offet are displayed at the bottom ofthe screen. Summer Time: Select Offor On to add one hour extra for summer time during the summer Date Date and Time settings are available only when GMT Usage s set to Of. Use he 0-9 buttons to enterthe date. Press EXIT to proceed. Time: Date and Time settings are available only when GMT Usage s set to Of Use he 0-9 buttons to enterthe time. Press EXIT to proceed, Time Display Select On to display time on screen, Of to remove.

‘This menu allows you to set up to 8 timed events for recording orwaking up the receiver. Use A Y to select Timer Setting from the System Setup menu and press OK to enter ‘The receiver ll display a ist th 8 timers followed by their respective status. Select the timer you wish to set or change with AV and press OK to proceed. ‘The timer setup menu will now be displayed. ‘The following settings are available: Timer Mode. Choose between Of ffimer inactive), Once or Dai (Timerwil be executed very day same time). Timer Service. Choose between Channel Timer wll wake up the receiver) or Record Timer wil start to record the scheduled event). Wakeup Channel Use 4 to selectthe channelthe timer wil wake up with Wakeup Date: Use the 0-9 buttons to input the date forthe timed event. On Time: Use the 0-9 buttons to input the start time. Duration: Use the 0-9 buttons to input the timer duration. When al settings are according to your ishes, use AW to move the highlight to Save and press OK 0 confinm. To quit the timer without saving your settings, move the highlight to Cancel. ‘This menu allows you to protect the installation menu and/or channels with a password. Vou can also enter a new password in the Parental Lock menu. 16 wwwsstrongtv

PART 1 English <STRON.

DIGITAL TV Use A Y to select Parental Lock from the System Setup menu and press OK to proceed. You wil be asked to enter your pin code. (DEFAULT PIN: 1234) Menu Lock Locks the installation menu, You can set MenuLock to On or Of. Rating Lock: Choose between: Of, ÂGE 10, AGE 12,…up to AGE 18. Channels with a parental rating above the chosen age wil be protected with a password (if available in your local broadcast) New Password Enter your new password (A digits) here. Confirm Password: Re-enter your password here to confirm.

‘This menu allows you to change settings for O$D Timeout and OSD Transparency. OSD timeout: Sets the time after which on screen banners and messages disappear. The range is 1-10 seconds OS Transparency. Ta setthe OSD transparency from Of 409% with 10% steps.

7.4.8 Favourite List Rename

This menu allows you to personalize the names ofthe 8 avaïlable Favourite ts. Use À V to select Favounie from the System Setup Menu and press OK to pracced. The names of al groups are now displayed Salctfavourte group th A. V and press OK edtits name. A text fildwil nov Pop upattheright the screen Use > À V to select characters andenter them with OK When youhave fiished eding, press BLUE to save the changes Wen al changes have been mad, press EXT tic.

7.4.9 Multiview Settings

This menu allows you to select how you like to display the mosaic for Multi vieu of more channel on your screen. This selection wil be activated you pres in viewing mode the MOSAIC button.

Press MENU in viewing mode to enter the Main Menu. Selectthe Too submenu with À V and press OK or to enter. Use A V to highlight the submenu of choice and press OK proceedl. Press EXT to leave.

7.5.1 Receiver Information

‘This submenu shows receiver specific information such as hardware version and software version. + also displays our web address wwwstrong.v. Please have the Information screen on hand when you call our hotine. The person who answers your call might ask for the information given in this screen.

7.5.2 Factory Setting

‘This option allows you to reset the receiver to factory settings, which clears all stored channels.

WARNING: By resetting your receiver to factory default all your settings and stored

channels will be permanentiy deleted. kwillrestore your receiver to an “out of he box” state. Please use this option with car. Use A Y to select” Factory Setting'in the Tools menu and press OK. You are asked to input password. www.strongtv 17

<STRONG PAT gl DIEMALI Input the correct password using the 0-9 buttons (DEFAULT PIN: 1234). À confirmation window is displayed. Select Yes to return to factory settings. Select No to cancel. Press EXIT to leave.

7.5.3 SW Upgrade by OTA

This receveris equippedith a manual and automatic OTA Over-The-A” sofware upgrade mechaniam. his menu allows you to manuall upgrade the Over-The-Air update ifthe automatic update mechanism does not function. might not be avalablein our region. Please visit our website un strong or contact your local service hotline for more information about this option. NOTE: When you suitch to Standby the OTA “Over-The-Ai” sofare upgrade mechanism vil check new sofiware is avalable During this process the LED on front wilight green. This cantake a couple minutes! Ie receiver found new software ll how a message the next time you switch the receiver to ON and you can confim to load. After an update the recever restants automatic}.

WARNING: During the upgrade process NEVER disconnect the receiver from the mains

or switch offthe power! Doing 0 might damage your eceiver and vil void warranty!

7.5.4 Upgrade by USB

‘This feature allows you to upgrade receiver software via the USB port. When new sofoware is available for our receiver, it can be downloaded from our website www strong. Place the software fill [unzipped)inthe root directory of your USB storage device (HDD, memory Stick etc) and insert this device into the USB por of the receiver. Select Upgrade by USB from the Tools menu and press OK to proceed. ‘The upgrade menu wil now be displayed. Use À Y to select Upgrade Mode and choose option Allcode Use A Y to select Upgrade File and choose the file containing the new software. Once all settings are made, move the highight to Start and press OK to start the upgrade process. ‘After a few seconds, the receiver asks: "Are you sure to burn flash?” Select Ves to finalize the upgrade or Noto quit without upgrading. NOTE: after a software upgrade, the receiver should behave in an unexpected way, please perform a factory reset as well. See chapter 7.5.2. After an update the receiverrestarts automatically.

WARNING: During the upgrade process NEVER disconnect the receiver from the mains

or switch offthe power! Daing 50 might damage your receiver and wl void warranty!

7.5.5 Remove USB device safely

Select Remove USB device safe) from the tools menu and press OK. The receiver will display a message indicating that you can safely remove your storage device from the receiver. 18 wwwsstrongtv

PART 1 English <STRON.

DIGITAL TV NOTE: ‘After perfomming this function, the USE device is no longer accessible from your receiver. To gain access to your storage device again, reinsertit or Switch the recever to standby and on again.

There may be various reasons for abnormal operation of the receive. Check the receiver according to the procedures shown below. the receiver does not work properiy after checking please contact your dealer or the local Service Hotine. Do NOT ty to open or disassemble the receive. may cause 2 dangerous situation and warranty Problem Possible cause Whatto do LEDindicator notit_| Mains lead unplugged Check mains plug Nosignalfound | Aeralis disconnected Check aeral lead Aeral is damaged/ Check aerial misaligned Check with dealer Out of digital signal area | Switchreceivers antenna power ON/ Active antenna requires to | connect extemal power switch ON antenna pouer/ external power No picture orsound | HDMIis notselected on Switch to correct TV input env your TVor Amplifier oris set || Selectlower resolution by pressingthe tohigher resolution as TV | V-FORMAT button on the remote control supports Switch on the TV. TVisnotswitched on Pidureisonÿin | Thevideoresolutionis Press the V-FORMAT button and select blackand white | selected on 50 or 60 Hz another frequency resolution No picture or Modulator on wrong channel | Select other channel, orlet TV scan for interference when _ | orwrong TV system. signal. Use correct TV system for our using the RF Interference on TVwhen | region. moduiator. using modulatar. Select other channel. Scrambled channel | Channelis scrambled Select alternative channel Message Noresponseto | Receieroff Plug in and turn on plug remote Remote not aimed correctiy _ | Aim remote at front panel control Front panel obstructed Check for obstructions Remote batteries exhausted _| Replace remote batteries Forgotten PIN code DEFAULT PINIS 1234 Contact local Service Hotine or send'email 0 our Support via wwwstrongiv www.strongtv 19

<STRONG PAT gl DIEMALI Problem Possible cause Whatto do Afermovingthe | Antennasignals are too weak | Press the INFO button on remote 2xto receiverto another call up signal bars and adjust antenna for room/area you {maximum) reception are no longer able orrescan channels to receive digital reception Thereceier Auto Standby function Disable auto standby. See section 7.3.4.2 Switches off enabled. for details automatically.

PART 1 English <STRON.