SRT 8106 - Satellite receiver STRONG - Free user manual and instructions

USER MANUAL SRT 8106 STRONG

1.1 Safety Instructions 2

3.1 Connecting to a Terestral Antenna 5

3.2 Connecting to TV with HDMI cable 5

3.3 Connecting to TV with SCART cable 5

344 Connecting to TV with Cinch cable 5

3.5 Connecting to a Digital Audio Amplifier with S/PDIF 5

3.6 Connecting to a Digital Audio Amplifier and TV using HDMI 6

3.7 Connecting a USB storage device 6

3.8 Connecting to a TV using modulator output 6

4.0 STARTING UP FOR THE FIRST TIME 6

5.0 QUICK GUIDE TO USING YOUR RECEIVER 7

6.1 Changing channels 3

www.strongtv English

1.1 Safety Instructions

DO NOT INSTALL YOUR RECEIVER: = In a losed or poorly ventilated cabinet; directly on top ofor under any other equipment; on a surface which might obstruct the ventilation slots. DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: = To direct sunlight or any other equipment that generates heat to rain or intense moisture; to intense vibration and to any shock which may cause permanent damage to your receiver or to any magnetic objects, such as loudspeakers, transformens, etc. Do not use a damaged power cord. I may cause a fre or an electric shock. Do not touch a power cord with wet hands. may cause an electric shock. When the receiver is not used for a long period oftime, you should unplug the power cord from the wall socket. = Do not use alcohol or ammonia based liquids to clean the receive. IFyou wish you may ean your receiver th a soR lintfree loth slightly made damp vith a mild soap solution, and only afer disconnecting from the mains voltage supphs Make sure no foreign objects fal through the ventilation slots because this could cause fre or an electric shock. Do not place any objects on top oFthe receiver because this might prevent proper cooling ofthe companents inside. Safety Precautions = Never ty to open the receiver.ILis dangerous to touch the inside ofthe receiver due to high voltages and possible electrical hazards. Opening the receiver will void the warranty ofthe product. Refer all maintenance or servicing to suitably qualied personnel. When you are connecting cables, be sure that the receiver is disconnected from the mains supph Wait a few seconds aller suitching ofthe receiver before you move the receiver or disconnect any equipment. Use only approved extension corde with compatible wiring that is suitable for the electrical power consumption ofthe installed equipment. Please ensure that the electrical power supply corresponds with the voltage on the electrical identification plate at the back ofthe receiver Ifthe receiver does not operate normal even afer strict following the instructions in this user manual, it is recommended to consult your dealer.

‘Your receiver and is accessories are stored and delvered in a packaging designed to protect against lectrc shocks and moisture. When unpacking i, make sure that al the parts are included and keep the packaging away from children. When transporting the receive iom one place to another or if you are returming it under warranty conditions, make sure to repack the recever in its original packaging with its accessories. Faling to compy vith such packaging procedures could damage the product and void jour warranty. 2 wwwsstrong:tv

Par gun <STRON DIGITAL IV

1.3 Equipment Set-up

Ve recommend you consul a professional installer to set up your equipment. Othenwise, please follou the instructions belouc 1 Refer to the user manual of your TV and antenna. = Make sure that the HDMI cable and outdoor components are in a good condition = Use only a HDMI 1.3 cable or igher for maximum performance. = 1Fyou use the TV SCART connection, use a well shilded SCART cable. = 1Fjou use the modulator connection, use a good quality coaxial RF cable This manual provides complete instructions for instaling and using this receiver. The following, symbols will serve as follout WARNING Indicates warning information. TPS Indicates any other additional important or hepful information. MENU Represents a button on the remote control or the receive. (Bold Characters) Move to Represents à menu tem within a window (halic Character)

= User Manual =_1 Remote control unit m 2x Batteries (AAA type) NOTE: ‘The batteries should not be recharged, disassembled, electrical short drcuited, be mixed or used with other types ofbatteres.

1.5 Usage of external USB devices

1m lis recommended to use USB 2.0 storage devices. your device is not compatible to USB 2.0 specications, multimedia functions of the receiver might not work proper. = To ensure best performance of your USB storage device please format by this receiver (menu “Medios") to FAT32 system. Other fl systems are not supparted by the receiver. However it is possible to use already NTFS formatted disk. STRONG cannot guarantee compatiblity with all types of USE storage devices. lis aduised not to store important information on USB storage deuices used vith the receiver. Alays make backups of data on your USB storage device before using it with this receiver. STRONG wil not take responsibility for any loss of information or cireumstances caused by loss of information

Decreases/increases the volume www.strongtv 3 English

3. AY (CHANNEL UP/DOWN)

Change channel to previous next

4. MODE INDICATOR: RED indicates that the receiver is in STAND.BY mode.

GREEN indicates that the receiver sin OPERATING mode.

5. 4 DIGITS DISPLAY: Indicates current time in STAND-BY mode

Indicates current channel number in OPERATING mode

6. IRSENSOR: Point your remote control towards this sensor.

1. ANTIN To connect to your antenna for the reception of broadeast signal.

2 TO To commet to ne terestial anterna input of your TV set. ‘his connection wil allow you to watch analogue terrestral programmes via the tuner in your TV.

3. SPDIF COAXIAL To connect Jour receive t a digital audio amplifier.

4. MODULATOR To connect to a TV using a coaxial cable

S. HDMI Te connect your eceiver with your TV set using a HDMI cable.

6. TVSCART Te connect your receiver with our TV set using a SCART cable

To connect your receiver with your TV set using a cinch cable.

8. AUDIO L/R CONNECTOR

0 connect your receiver with your TV set using a cinch cable. s. uss Connector for USB hard disk devices

10. POWER CORD Your receiver requires a voltage of 220-240 AC (Auto.

selectable), 50/60Hz 25%. Check the local pouer specification before connecting your receiver o the wall outlet.

1.0 ‘ur the receiver On/Standby

2 @ Mutes audio output ofthe receiver

3. PG+PG- Page up/doun and 10 channels steps in channel ist mode

12. RECORD Records the TV programme to the connected storage device

14.09 “Channel selection or value input

15.EPG Shows the EPG (Electronic Programme Guide) in TV mode

16. RECALL Back to previous shovum channel

17. AUDIO Sets the current audio channel t le, right or stereo

18. TV/RADIO oggles between TV or RADIO mode

19.FAV Favourite group selection

20. FILE Shows the Media Player ist

21.77X Shows Teletext on OSD (On Screen Display) 22 SUBTITLE Shovs list of subtile languages 23.40% Fast rewind/Fastfonvard

24. COLOURED BUTTONS

For Multimedia and Teletext functions

3.1 Connecting to a Terrestrial Antenna

To receive broadcast signal your trrestral indoor or outdoor antenna must be connected to the ANT IN connector on the back of the receiver. Use a propery shielded antenna cable and suitable connectors. The TO TV connector allous you to loop the antenna signal to a second receiver or TV set.

3.2 Connecting to TV with HDMI cable

Fig.4 The TV set shall be connected with the receiver using a good quality HDMI 1.3 or higher cable. This connection gives the highest possible qualit

3.3 Connecting to TV with SCART cable

SRT 8106 is also equipped with a SCART connectoraltemativel, he TV set can be connected to the receiver using a good quality SCART cable.

3.4 Connecting to TV with Cinch cable

TV sets without SCART or HDMI input{s) can be connected to the receiver using suitable cinch cables. Connect one end ofthe cable to the Audio L, R and VIDEO connectors on the back of SRT 8106. Connect the other end to the respective inputs on your TV set.

3.5 Connecting to a Digital Audio Amplifier with S/PDIF

Fig.4 By connecting your receiver to a digital amplifier or home theatre system, you can enjoy the best possible sound quality and mul-channel audio (depending on broadcast}. Connect your Digital Audio Ampliier or home theatre system with a suitable cinch cable to the S/PDIF connector on the back oftne receive. www.strongtv 5 English

<STRONG PART 1 Eng GA Ty

3.6 Connecting to a Digital Audio Amplifier and TV

using HDMI Fes By connecting your recever to ie latest digital amplifers or home theatre systems with HDMI connections you il enjoy the best possible sound quality and mul-channel audio (depending on broadcast). Connect the HDMI output ofthereceiver to an input of your amplifier, and then connect the HDMI output oFthe amplifier to your TV set. Select the correct input on your amplifier to watch and listen to programmes.

3.7 Connecting a USB storage device

Fig.4 NOTE: Ve recommend the use of a hard disk drive USB 2.0 or higher for recording and play back OFTV events. For proper functioning of Time Shi and recording functions, a fast USB device [such as a hard disk drive) is needed. Interrupted playback or a distorted picture during playback or Time Shif are indications for a low device speed. STRONG cannot guarantee proper functioning of recoding and or Time Shi functions with all USB devices.

3.8 Connecting to a TV using modulator output

Fig. 6 To view a TV channel on your TV {or a TV setin another room), atermativel you can use the UHF analogue modulator output and connect it with a suitable coaxial cable to the (other) TV set. You must et the (other) TV set search or scan fr the RF signal out ofthe modulator (Refer to the manual of our TV set) Default channel is 38, PAL-BG, but is adjustable in the System setup menu in the TV system. Choose a channel which is not occupied by TV transmiters in your region to avoid iterference. Please note, if other connection options are available on your TV set these are preferable.

4.0 STARTING UP FOR THE FIRST TIME

IF jou use your eceiver for the first time, the Welcome “Easy install” menu appears. Use À W to move the highlight t the setting you wish to alter and use 4) to change values. Start by selecting your language using 4). Once you have selected your language, press W to move the highlight to the nest item and use 4 to change. Language Select your language. Region: Select your region where this receiver is used. Sub: Select Normal to display subtiles per default, Select Hard of Hearing to show HoH subtiles per default. Select Offto hide subtiles per defaut. Aspect Mode: Use this option to select the aspect ratio of your TV and the preferred conversion method. Options are: Auto (automatic detection of aspect ratio), 4:3 Panscan (Displays 169 widescreen broadcasts full screen on your 43 TV), 43 leterbox (black bars on top and under the picture on a 4:3 TV) and 169 {use this setting for 16,9 TV sets). 6 wwwsstrong:tv

Par gun <STRON DIGTAL IV ‘Scan mode Select AÏ to store scrambled and fre to air channels or select Free to store on free to air channels. Note: Scrambled channels you cannot watch with this receiver Connection: Use this option to select the connection to your TV set. Select HDMI or SCART. Iyou are using a inch cable then this selection is not important. Once all settings are made, move the highight to OK and press OK to continue. NOTE: Wrong region selection can lead to missing channels or channels being. stored on wrong positions in the channel ist. The receiver will now advance to the Aerial Adjustment screen This part ofthe wizard is of great help when setting up your antenna system. Use A Y to move the highlight to the setting you wish to alter and use 4 to change values. The felloving settings are available: Antenna Power: Set to On if you use an active antenna. When set to On, 5 V will be present on he ANT IN connector ofthe receive. Select Offor passive antennas. Beeper Select On for an audible indication of signal reception. Offturms the beeper of. Channel No. Select a channel that is know to carry a broadast in your region. The Signal Strength and Signal Quality bars give a visual indication ofthe reception. AAdjust your antenna to obtain maximum signal strength and qualit. Once all settings are made, press OK to start scanning. The receiver will now search for all available channels. Once scanning is finished, the receiver svitches to viewing mode. La In case the Welcome “Easy install” menu does not appear afer suitching on he receiver the first time, reset the receiver to factory settings by pressing the MENU button and selecting Tools, then submenu Load Factory Setting. {Default PIN 0000)

5.0 QUICK GUIDE TO USING YOUR RECEIVER

Ve at STRONG understand that you can't wat to enjoy your new high definition digital terestial receiver The following quick guide wil make you familiar with the basic operation f this device. We do, however, advice you to read the full manual to get the best performance from your receiver To turn your receiver ON or to Standby, use the W button on the remote contel. Choose the desired channel with the À W buttons. Alternative you can igi the channel number with the 0-9 buttons on the remote control. Or press OK in vieuing mode to display the channel ist. The volume can be adjusted with the 4 buttons

Your new receiver is equipped with several features to make watching TV a true pleasure. This paragraph describes these features. Please also read chapter 7.0 o get amiliar vith the menu of your receive. www.strongtv 7 English

<STRONG PART na DIEMALIV

6.1 Changing channels

‘To gain direct access to a certain channel, simply input its number with the 0-9 keys on the remote “control. Channel numbers can be up to four digits long. Entering a number with less than four digits is possible. Just wait a few seconds and your receiver wi switch to the selected channel or press OK immediately afler selecting the channel number

Press OK in viewing mode to display the Chanmel Lis. Use À W in the Channel List to highlight your “channel of choice and press OK once to select the highlighted channel. Press OK again to leave the Channel List. TP: Use 4 to toggle beteen the Al Channel ist and Favourite ist or press FAV for a list ofavalable Favourite lists. 6:1.3 Using the A v or PG+/PG- keys À suitches to the net channel °Y suitches to the previous channel. PG+ suitches to the next 10 channels. PG:switches Lo the previous 10 channels.

file watching TV you can press the INFO button any time to get information about the current channel and event. Press INFO twice for extended EPG deals about the curent channel. Press INFO three times for technical details about the current channel. er mate dan ae Ab depart

6.3 Selection of audio language

Some channels support a choice of audio formats and/or languages. To select another audio stream, press AUDIO in viewing mode. À lis th available audio streams will now be displayed. Use À W to Select the desired stream and confirm with OK. The audio channel as stereo, mono, lef and right can be selected with the 4 buttons.

Your recever includes a ful featured Teletex To access Teleteu, press the TTX button in vieuing, mode and use the 0-9 buttons to input the number ofthe page jou wish to see. The coloured buttons ofthe remote control allow you t jump to selected pages direct as indicated om the bottom fthe teletext screen. Use the À W buttons to select one page up or down, use 4 buttons to select subpages. Press EXIT or TTX to get back to viewing mode.

Some channels support a choice of subtile languages. Press SUBTITLE in viewing mode t display à lis ofavalable subtil languages. Select your subtile ofchoice with À W and press OK to conf. Press EXIT t leave without making changes.

Time Shi allous you t pause Ie broadeasts and resurne playback later. Press TIMESHIFT in viewing mode to activate this mode. On screen wil appear a message Timeshjf On, live TV kecps playing. To pause press I button and press BLUE to resume Time shifled playback. Press 4 or Fast reind/Fastfonvards. Press RED to return to [ve TV. Press TIMESHIFT Lo ext Time Shi mode. NOTE: ‘Time Shif needs a connected USB storage device with sufficient free space and sufficient speed in order to work proper.

6.7 EPG (Electronic Programme Guide)

‘The Electronic Programme Guide is a very useful function that allows you to view event schedules and information and to mark programmes for recording, To access the EPG, press the EPG button in viewing mode. Use A V to select the desired channel and 4 to select the desired event. Press OK to display detailed information on the selected event. Use EXIT to quit the detailed information screen. Press RED to get to the Step Time function. Use 4 to select the desired step and OK to execute it. Press EXT to qui the Step Time function. Press GREEN to set a timer for a selected event Refer to section 7.34 for details on the timer function NOTE: AAvailability of EPG data depends on broadcast.

6.8 Instant Recording

Your new receive allows you to make an instant recording of the programme you are watching Simply press RECORD to star he recording, To enter the duration fr the recording, press RECORD again. Use the 0-9 keys to imput the desired recording time and press OK to confim. During the stat of a recording, a recording sign wi short be shou on the upper le of your TV screen. To stop the recording, press RED. Select Ys and press OK again to stop the recording

‘The main menu gives you access to settings, multimedia functions and buil in games. To access the main menu, press MENU in vieng mode. The main menu consists of the following sub menus: Edit Channel, Installation, System Setup, Tool, Game and Media+ ‘Throughout he main menu, MENU or EXIT can be used to get back to the previous screen

Use À Y to select Edit Channel and press OK or b to enter. Use À Y to highlight the desired sub menu and press OK to select. Press EXIT or 4 to get back to the main menu. www.strongtv 9 English

<STRONG PART na DIEMALIV

7.1.1 TV Channel List

In Edit Channel menu select TV Channel List with A V and press OK to enter. Use 4 10 change the channel group (assumed you have ready set up favourite groups) Select the desired channel with À W. Press OK to view the selected channel in he preview box.

7.1.2 Adding channels to favourite lists

Channels from the TV Channel List can be added to up to 8 different favourite groups. Press FAV while in TV Channel Lit to access this function. The FAV sign on the top ofthe screen vill move up Lo indicate that the Favourite function is selected. Use À Y to select a channel you wish to add to 2 favourite group. When the highlight is on the desired channel press OK. À list with all available Favourite lists will now pop up. Use A Y to select the favourie list you wish to add the channel to and press OK, press EXT to finalize the process. Favoured channels ll be marked vith a heart symbol. Once all changes are made, press EXIT tice. À confirmation banner will pop up. Select Yes to save he changes or No to discard.

7.13 Locking channels

Locked channel ean ny be watched ar enterig the pi code. (DEFAULT PIN: 0000) Fo lock orunlock a channel, press RED while in TV Channel Lis. The red Lock sign onthe top ofthe screen wi move up to indiate that the Lock function selected. Use AY to select the desired channel and press OK to lock or unlock it. You are asked to input the in code. (DEFAULT PIN: 0000) Locked channel ll be marked withthe & symbol. Lockimg/unlocking multiple channels in one session is possible. Once al changes are made, press EXT tice. À confirmation banner vil pop up. Select Yes to save the changes or No to discard, Locking/unlocking multiple channels in one session is possible.

7.14 Skipping channels

Channels marked with Si vil be skipped when zapping channels with the À V buttons. Despite that, these channels are sil avañable from the channel it. Fo mark channel for skpping, press GREEN vil in TV Channel Lis The Skjp symbol on the top of the screen wil move up o indicate that the Skip function is selected. Use À W to select the desired channel and press OK to mark or ummark for skipping, Channels se for skipping will be marked with the = symbol. Once all changes are made, press EXT tvice, À confrmaion bare vil pop up Select Yesto save the changes or No to discard

7.1.5 Moving channels

To enable the Mave function, press YELLOW ue in TY Channel Lis. The Move symbol on the top of the screen will move up to indicate that the Move function is selected. Use À W to select the desired channel and press OK to select. You can now move the selected channel up or dou he channel lis using À W. Once the channel is on the desired position, press OK again. The channel is nou fied on its new position. Once al changes are made, press EXT vice. À confirmation banner vil pop up. Select Yes to save the changes or No to discard.

7.16 Editing channels

he Edi function allows ou to So, Rename ar Delte channels, To enterthe Edit menu, press BLUE while in TV Channel List. The Edit Channel menu ill appear. w wstrongiv

Par gun <STRON DIGITAL IV Sort Press RED 10 enter the Sort menu Use A Y to select the desired sorting method and press OK to confim. Pessible methods are Name (AZ): Soring in alphabetcal order from A to Z. Name (ZA) Soring in alphabetcal order from Z to A. Free/Scramble: First in the list will be Free-To-Air channels. Lock All unlocked channels wi placed first in the list. Default: Sortng by searched Order [rom lave to highest frequency or by LEN numbering). Rename Press GREEN in Edit Channel to enable the Rename function. The Rename sign will move up to indicate that Rename is selected. Use A W to highlight the desired channel and press OK to select it. Atext field will now pop up atthe right ofthe screen. Use @ A W to select the desired characters and enter them with OK. Once you have finished editing, press BLUE to enter the changes. Once all changes are made, press EXIT twice. Select Ye to save the changes or No to discard. Delete Press BLUE in Edit Channel to enable the Delete function. The Delete sign will move up t indicate that Delee is selected. Use A W to highight the desired channel and press OK to mark it for deletion. The recever asks jou to enter the pin code, Once you have marked al channels you wish to delete, press EXIT ice. À confirmation banner will be displayed. Select es to delete the marked channels or No to cancel,

7.1.7 Radio Channel List

Basical, the operation ofthe Radio Channel List is the same as in the TV Channel List, The only difference is that in Radio Channel List there is no video information, so it will always display the radio logo atthe right preview screen.

Use this menu to delete all stored channels. Select Deete All with À W and press OK. The receiver asks you to enter the pin code. (Defaul pin:0000). In the confirmation window select Yes with > and press OK to delete or select No to cancel WARNING ‘The Delete al function will permanently delete al current channels and all Favourite lists from your receiver, and you are not able to leave the menu until you search for channels again.

Use A Y 10 select Installation and press OK or D to advance. Select Auto Scan with À W and press OK to enter. Use 4 10 toggl beteen FTA On Yes or Ne. When FTA Only is set to Yes, scrambled channels wont be stored in the channel st. Use À W to highlight Search. Now press OK to start auto scan ‘The receiver il store ll new found channels in the channel is www.strongtv n English

Use À Y 10 select Installation, press OK or D to advance. Use À Y 10 select Channel Scan and press OK 19 enter. Use 4 10 toggl betneen available scan modes: By Channel and By Frequency. 1FBy Channel is selected, use the eursor buttons to select Scan Band and Channel Ne. By Frequency is selected, use the cursor buttons to select Frequency and Bandvidth. Highlight Search and press OK Lo start scanning. Nes found channels wall be stored in the channel ist.

7.23 Aerial Adjustment

Use A Y to select installation, press OK or to advance. Use À Y to select Auril Adusment and press OK to enter. Use À Y move the highlight to the setting you wish to alter and use 4 to change values. The following setings are available Antenna Power. Set to On ifyou use an active antenna. When set to On, 5 V will be present on the ANT IN connector ofthe receiver. Select Of for passive antennas. Besper Select On for an audible indication of signal reception. Offturs the beeper of. Channel No. Select a channel that is known to carry a broadcast in your region. The Signal Strength and Signal Qualiy bars give a visual indication ofthe reception. AAdjust your antenna to obtain maximum signal strength and qualit} Press EXIT to leave the Aeral Adjustment screen.

7.2.4 LCN (Logical Channel Numbering)

1FLCN (Logical Channel Numbeing) is activated and an LCN signal is provided bythe operator, channels vil be storedin an operator defined order, St LCN to On to activate operator defined channel numbering or Ofto store channels in found order

‘This menu allous you to manage the system settings of your recever. I consists oFthe following sub» menus: Lamguage, TV System, Local Time Seting, Timer Sting, Parental Lock, OSD Settng, Favourite and Auto Standby. Press À V to highlight desired menu and press OK advance to the next screen. Use À W to move he highlight to the desired setting. Values can be changed with 4e. Press EXT to leave.

‘This menu allous you to set up your language preferences. Language: Use 4 to select the desired language for the On Screen Display. First Audio: Use 4 to select the desired Audio language. Second Audio: Use 4 to select a language that will be played when the language selected at Fist Audio isn't available. Subiïle Language: Use QD to select the preferred subtile language. Subite Use 4 to select the preferred subtile ype to be displayed automaticalh: Téltet: Use 4 to select the preferred teletet language (when available) m2 wwwsstrong:tv

Use this menu to match your receiver to your TV set. The following setings are available Video Resolution: Toggles betueen 576 up £o 10B@. Please use a seing that matches your ‘TV's specifications. Afler a selection is made, you wall be asked to confim. Note: Selection is only applicable on HDMI ‘Aspect Mode: Use this option to select he aspect ratio of jour TV and the preferred “conversion method. Options are: Auto (automatic detection of aspect ratio), 4:3 Panscan (Displays 16:9 widescreen broadcasts full screen on your 43 TV) 433 letterbox (black bars on top and under the picture on a 43 TV) and 16:9 {use this setting for 16:9 TV sets) Connection: Use this option to select the connection to your TV set, Select HDMI or TV SCART. RE System: When using the builtin RF modulator you can select here your TV sets analogue reception system. Default is PAL-BG, RF Channel Set the RF channel ofthe modulator. Default is channel 38. Digial Audio Output: | Toggles beteen PCM and Bistream output. When PCM is selected, all audio villbe converted to stereo audio. Bitstream enables multi-channel audio on the digital output.

7.3.3 Local Time Setting

Here you can set up your region and time zone. Region Use 4 to select he region you live in GMT Usage Set to On for broadcaster defined time or to Offto input time and date manualh. GMT offer: Allous you to adjust the time zone you le in. This option s only avalable when GMT Usage is setto On. The GMT Offéet range is ".11:30 — +12:00°, increasing by halfhours progressive}, The cities matching the set GMT Offet are displayed at the bottom ofthe screen, Summer Time: Select Offor On to add one hour extra for summer time during the summer. Date: Date and Time settings are available only when GMT Usage is set to Of. Use the 0-9 buttons to enter the date. Press EXIT to proceed Time: Date and Time settings are available only when GMT Usage is set to Off Use the 0-9 buttons to enter he time. Press EXIT to proceed.

This menu allows you to set up 10 8 timed events for recording or waking up the receiver. Use A V to select Timer Setng from the Sjatem Setup menu and press OK to enter. The receive vil display a list with 8 timers, followed by their respective status, Select the timer you wish t set or change with À W and press OK to proceed The timer setup menu will now be displayed The following setings are avalable: Timer Mode: Choose bemueen Of (Timer inactive), Once or Daily (Timer il be executed every day Timer Seic: Choose betueen Channel (Timer will wake up the receiver) or Record {Timer wil start t record he scheduled event) Wokeup Channel Use 4 to select the channel te timer will wake up with

www.strongtv English

<STRONG PART na DIEMALIV Vkeup Date: Use the 0-9 buttons to input the date for the timed event. Wkeup Time: Use the 0-9 buttons 10 input the desired stat time. Duration: Use the 0-9 buttons to input the timer duration. Once all settings are according to your wishes, use À W to move the highlght to Save and press OK 0 confim. To quit the timer without saving your settings, move the Highlight to Cancel

‘This menu allows you to protect the instalation menu and/or channels with a password. You can also enter a new password in the Parental Lock menu. Use A to select Parental Lock from the System Setup menu and press OK to proceed. You will be asked to enter your pin code. (DEFAULT: 0000) Menu Lock Locks the instalation menu. You can set Menu Lock to On or Of. Channel Locke Choose betueen: Off AGE 4, AGE 5, up to AGE 18. Channels with a parental rating above the chosen age wall be protected with a password (available in your local broadcast.) New Password Enter your new password (4 digits) here. Confirm Password: Re-enter your password here to confirm.

This menu allows pou 0 change setngs fr. OSD Timeout and OSD Transpareney. OSD imeour Sets ie time fier which on screen banners and messages disappear. The range is 1-10 seconds. OSD Transpareney To setthe OSD transparencyfom Of 40% with 10% steps Load Default OSD Serie Press OK to clear all OSD setngs and reset to defaut values

This menu allows you to persomlize the names ofthe 8 available Favourite lists. Use A V 10 select Favourite from the System Setup Menu and press OK to prceed. The names ofal groups are now displayed. Select the desiredfavourite group with A V and press OK to cdit ts name. À text field will now pop up at the right oftne screen. Use AD À V to select the desired characters and enter them with OK. Once you have inished editing, press BLUE to save the changes. Once al changes are made, press EXIT vice.

Auto Standby is a new feature that helps you with reducing power consumption. When set to On, the receiver will tum to standby ii doesn't receive any commands for three hours. Set Auto Stand to Ofio avoid the automatic switch doun.

7.4.1 Receiver Information

‘This submenu shows receiver specific information such as hardware version and sofware version. I also displays our web address wawstrong.w. Please have the Receiver Information screen on hand when you call our hotline. The person who answers your call might ask for the information given in his screen

7.4.2 Load Factory Setting

‘This option allows you to reset the receiver to factory settings, which clears al stored channels. Wamingl 8y resetting your receiver to factory defaut all your settings and stored channels will be permanent} deleted. Please use this option th care. Use A to select “Load Factory Setting” in the Tools menu and press OK. You are asked to input password Input the correct password using the 0-9 buttons (default: 0000). À confirmation window is displayed. Select Yes to return to factory settings. Select No to cancel. Press EXIT to leave.

7.4.3 SJW Upgrade by OTA

his recever is equipped with an Over The Ar soflware upgrade option An Over The Air update right ot be available in your region Please visit our website wrong. rfrontact your local semi hotline for more information about this option

7.4.4 Upgrade by USB

This feature allows you to upgrade your recevers sofare ia the USB port 1Fnew software is available for your recever it can be dounloaded from our website ww ftrOnE Face the sofa fle [unzipped} in the root directory of your USB storage device (HDD, memory Stick etc.) and insert this device into the USB port fe recever. Select Upgrade by USE from the Took menu and press OK t proceed. The upgrade menu will now be displayed Use À W to select Upgrade Mode and choose option Alode. Use A V to select Upgrade Fil and choose the file containing the new sofware Once al setings are made, move the highlight to Stat and press OK 1o start te upgrade process. Afir a feu seconds he receiver ask: "Are You sure o burn flash? Select Yet fnalize the upgrade or No to qui without upgrading, WARNING! AAfer an update the receiver restarts automatically, During the upgrade process NEVER disconnect the receiver from the mains or switch ofthe poverl Doing s0 might damage your receiver and wil void warranty! www.strongtv 15 English

<STRONG PART na DIEMALIV

7.4.5 Remove USB device safely

Select Remove USB device safly from the tools menu and press OK. The receiver will display a message indicating that you can safely remove your storage device from the receiver. NOTE: fer performing this function, the USB device is no longer accessible from your receiver. To gain access to your storage device again, re insert or switch the receiver to standby and on again.

Your recever is equipped with two games which can be played on your TV sereen using the receiver remote control, Use À Y to select Game fiom the Main menu and press OK or D 10 proceed. Select one ofthe available games (Othello or Sudoku) using À W and press OK to start the game. Follow the directions on screen. Use EXIT to quit a game.

‘The Media menu consists ofthe following submenus: Media Player, Record Manager, DVR HDD Information, HDD Format, DVR Configuration and Jump. Use À 10 highlight the desired menu and press OK to enter. Press EXIT to quit.

his function alows You to play MPEG, AVI, MP3, JPG many other type fes from connected storage device (see details in technical part) Select Media Player from the Medias menu and press OK to proceed Use A Y browse the connected USB device and use OK to open folders. Press OK to play the highighted selection. The help banner atthe bottom ofthe screen xplains ll buttons used in the Media player. Press EXIT to qu. NOTE: You can also access the Media Player fiom vieuing mode with the FILE key on the remote control.

7.6.2 Record Manager

The Record Manager gives you access to previous recorded events Select Record Manager from the Media+ menu and press OK to enter. Use A V to highight the recording you wish to play and press OK start playback Press EXT to ext. During plaÿback ii possible to perform the following actions:

To pause the playback >» Fo resume playback «4» For fast forward or as reuind during playback RD Press to stop playback and return to Record Manager. 16 wwwsstrong:tv

Par gun <STRON DIGITAL IV ‘When the timer banner is on screen (activated by pressing > or INFO), the following actions are possible: 4 and press OK to jump forwards and backwards in time during playback. = Set marker point in play back, press again to delete marker point. 2 Jump to next marker point. 3 Jump forward in time. (See details in 7.6.5 DVR Configuration under Sep to) NOTE: You can also access the Record Manager from viewing mode with the RED Key on the remote control. The help banner at the bottom ofthe screen “explain all buttons used in this record manager to edit. Press EXIT to save the settings and quit the menu

7.6.3 DVR HDD Information

‘This option shows relevant information about the connected USE device. Select DVR HDD Information frorn the Media menu and press OK to enter. Press EXIT to leave.

‘The HDD format menu allows you to format the connected USB device. WARNING! Formatting will permanent} delete ALL data stored on the connected device Please make a backup copy of al data you wish to keep before entering the HDD Format menu. STRONG cannot be held responsible for loss of data from USB devices used vith this receive. Select HDD Fonnat om the Media+ menu and press OK to enter. Use @ to select the partition you wish to format (Parition 1 is set per default and press V to ighight Fommat. Press OK to procecd, select Yes or No, or press EXIT to leave vithout formating NOTE: It is possible to use already NTFS formatted USB disk.

7.6.5 DVR Configuration

‘This menu allous youto make settings for Time Shif, recording and playback Select DVR Configuration from the Media» menu and press OK to enter. Use A V to move the highlight and 4 to change settings. Press EXIT to quit. Time Shi: On or Of. When Time Shif is set to Of, Time Shift becomes inactive. Time Shifi to Record: … On or Off. When set to On, Time Shif is also possible during record Record Tipe: TS or PS. When TS is selected, recordings will also include subttles and eletext (uen available). PS makes recordings without these etras. Record Selection Select the partition whereto the receiver should record. Standby afer record On or Off. Select ifreceiver must go to standby mode after Timer record. Step te: 30sec to 10 min. Set the time step you like to jump forward vith the button 3 during playback of recorded iles www.strongtv 7 English

‘There may be various reasons for abnormal operation of the receiver Check the receiver according to the procedures shown below Fe receiver does not work proper} afier checking please contact your dealer or the local Service Hotline. Do NOT try to open or disassemble the receive. It may cause 2 dangerous situation and warranty will be void Problem Possible cause What to do LED indicator not it Mains lead unplugged Check mains plug No signal found Aerial is disconnected Aerial is damaged/misaligned Out of digital signal area {Active antenna requires to switch ON antenna power/ external power Check aerial lead Check aerial Check with dealer Suitch receiver's Antenna Power ON/connect external power No picture or sound on TV HDMI is not selected on your TV or Amplifier or is et to higher resolution as TV supports. TV is not switched on Switch Lo correct TV input Select lower resolution Switch TV on No picture or interference When using the RF modulator. Modulator on wrong channel or wrong TV system: Interference on TV when using modulator. Select other channel, orlet TV scan for signal. Use correct TV systen for our region. Select other channel. Scrambled channel Message Channelis scrambled Select alternative channel No response to remote control Receiver of Remote not aimed correct Front panel obstructed Remote batteries exhausted Plug in and turn on plug {im remote at front panel Check for obstructions. Replace remote batteries Forgotten PIN code Default PIN is 0000 Contact local Service Hotine or send email to our Support via vawstrong iv Afler moving the receiver Lo another roomfarea you are no longer able to receive digital reception Antenna signals are 100 weak Press the INFO button on remote 2x or 3x to call up signal bars and adjust antenna for (maximum) reception or rescan channels The receiver suitches of automaticalh. Auto Standby function enabled. Disable auto standby. See

DIEMALIV Connectors ANT IN IEC Female TO TV-IEC Male (TV SCART (RGE, CVBS, Audio LBR) HDMI13 MODULATOR — IEC Male SJPDIF. coaxial output Cinch Cinch (Audio LBR and Video CVBS) USB 2.0 port: General Data Supply Voltage: Power Consumption: Power consumption in Standby: Operating Temperature: Storage Temperature: Operating Hurnidity Range: Size (Wx D x H) in mm: Netweight 5 V/800 mA (max) supported 220-240 V AC (SMPS), 50/60 Hz