STRIKE Array 2C - Uncategorized Chauvet - Free user manual and instructions
Find the device manual for free STRIKE Array 2C Chauvet in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | LED Lighting Fixture |
| Model | STRIKE Array 2C |
| Brand | Chauvet |
| Dimensions (L x W x H) | 12 x 8 x 6 inches |
| Weight | 5 lbs |
| Power Supply | AC 100-240V, 50/60Hz |
| Power Consumption | 120W |
| Light Source | RGB LED array |
| Control Protocol | DMX512 |
| DMX Channels | 4 or 8 selectable |
| Beam Angle | 120 degrees |
| Housing Material | Aluminum |
| IP Rating | IP20 (indoor use only) |
| Operating Temperature | 14°F to 113°F (-10°C to 45°C) |
| Cooling | Convection |
| Mounting Options | Floor stand, truss clamp, or hanging bracket |
| Included Accessories | Power cord, user manual |
| Maintenance | Clean with dry soft cloth; avoid solvents |
| Safety Precautions | Do not expose to rain or moisture; disconnect power before cleaning |
| Warranty | 2 years limited |
| Repairability | User replaceable fuse; service by qualified technician |
Frequently Asked Questions - STRIKE Array 2C Chauvet
How do I set the DMX address on the STRIKE Array 2C?
Use the menu buttons on the control panel to navigate to 'DMX Address'. Set the desired address using the up/down buttons. Refer to the DMX protocol chart in the manual for channel assignments.
Can I use this fixture outdoors?
No, the STRIKE Array 2C is rated IP20 and must be used indoors only. Exposure to rain or moisture can damage the unit.
What type of power cable does the fixture use?
It uses a standard IEC power cord (Edison plug for US). Always connect to a grounded outlet with the correct voltage as specified on the label.
How do I clean the LED lens?
Use a dry, lint-free soft cloth to wipe the lens gently. For stubborn dirt, slightly dampen the cloth with water. Do not use alcohol or abrasive cleaners.
The fixture is not responding to DMX. What should I check?
First, verify that the DMX cable is properly connected and not damaged. Check the DMX address setting and ensure the controller is set to the correct address. Try a different cable or port.
How many fixtures can I daisy-chain on one DMX line?
The maximum recommended number is 32 units per DMX line. For longer runs, use a DMX booster/splitter to maintain signal integrity.
What is the beam angle of the STRIKE Array 2C?
The beam angle is 120 degrees, providing a wide wash of light suitable for uplighting or stage lighting.
Can I replace the LED array?
The LED array is not user-replaceable. If it fails, contact Chauvet customer support for repair options. Do not attempt to open the fixture.
How do I select the DMX channel mode?
Press the Menu button until 'DMX Mode' appears. Use the up/down buttons to toggle between 4-channel and 8-channel modes. Press Enter to confirm.
What do the LED indicators on the control panel mean?
A solid green light indicates normal operation. Flashing green means DMX signal is present. Red indicates a fault condition. See the manual for troubleshooting.
User questions about STRIKE Array 2C Chauvet
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual STRIKE Array 2C - Chauvet and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. STRIKE Array 2C by Chauvet.
USER MANUAL STRIKE Array 2C Chauvet
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Chauvet
Model : STRIKE Array 2C
Category : Uncategorized