XPA-700 - Receiver Omnitronic - Free user manual and instructions
Find the device manual for free XPA-700 Omnitronic in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type | Power amplifier / receiver |
| Model | XPA-700 |
| Brand | Omnitronic |
| Rated output power | 700 W RMS (stereo @ 4 Ω) |
| Frequency response | 20 Hz - 20 kHz (±1 dB) |
| Input sensitivity | 1.2 V (RMS) |
| Input connectors | XLR, 6.3 mm jack, RCA |
| Output connectors | Speakon, binding posts |
| Impedance | 4 Ω - 16 Ω (stereo), 8 Ω (bridge) |
| Dimensions (W × H × D) | 482 × 88 × 350 mm (19", 2U) |
| Weight | 11.5 kg |
| Power supply | AC 230 V / 50 Hz, 1200 VA |
| Protection circuits | Short circuit, thermal, DC offset, overload |
| Cooling | Variable speed fan (temperature controlled) |
| Operating temperature | 0 °C to 40 °C |
| Mounting | 19" rack mount (2U) |
Frequently Asked Questions - XPA-700 Omnitronic
How do I connect speakers to the XPA-700?
Use Speakon connectors for high-power or binding posts for bare wire or banana plugs. Ensure impedance is between 4 Ω and 16 Ω per channel.
Can I bridge the amplifier to get more power?
Yes, set the bridge mode switch (if available) and connect the speaker across the positive terminals of channel A and B. Minimum impedance is 8 Ω.
What is the recommended input signal level?
The input sensitivity is 1.2 V RMS for rated output. Do not exceed 10 dBu to avoid clipping.
How do I clean and maintain the amplifier?
Unplug the unit and use a dry, lint-free cloth. Do not use liquids or solvents. Periodically check and clean the air vents to prevent overheating.
What does the protection LED indicate?
The protection LED lights up during power-on delay, or when short circuit, overheat, or DC offset is detected. In such case, the amplifier mutes the output.
Can I use the XPA-700 with an audio mixer?
Yes, connect the mixer's output (XLR or 6.3 mm jack) to the amplifier's input connectors. Ensure the mixer's output level does not exceed the amplifier's input sensitivity.
What is the maximum power consumption?
Maximum power consumption is approximately 1200 VA at full load. Use a properly rated mains circuit.
Does the amplifier have a standby mode?
There is no dedicated standby button; however, when no signal is present for a few minutes, the amplifier may enter a low-power state (depends on design). Check front panel indicators.
How do I replace a blown fuse?
Disconnect from mains. The fuse holder is located near the power inlet. Replace only with the same type and rating (e.g., 10 A, 250 V slow-blow). If fuse blows again, consult a technician.
Where can I find spare parts or service manual?
Contact Omnitronic customer service or an authorized dealer. Provide model XPA-700 and serial number. The service manual is available for qualified technicians.
User questions about XPA-700 Omnitronic
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual XPA-700 - Omnitronic and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. XPA-700 by Omnitronic.
USER MANUAL XPA-700 Omnitronic
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Omnitronic
Model : XPA-700
Category : Receiver