FT-2980R - Talkie Walkie YAESU - Free user manual and instructions
Find the device manual for free FT-2980R YAESU in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | VHF FM Transceiver |
| Brand | Yaesu |
| Model | FT-2980R |
| Frequency Range | 144–148 MHz (amateur band) |
| Output Power | 80W (high), 30W (medium), 10W (low) |
| Modulation Modes | FM, F3E |
| Number of Channels | 200 memory channels |
| Power Supply | 13.8V DC ±15%, negative ground |
| Current Drain | Approx. 13A (transmit high power) |
| Dimensions (WxHxD) | 140 x 40 x 180 mm (5.5 x 1.6 x 7.1 in) |
| Weight | 1.1 kg (2.4 lb) |
| Operating Temperature | -20°C to +60°C |
| Antenna Impedance | 50 ohms, SO-239 connector |
| Audio Output Power | 2W (internal speaker), 4W (external at 8 ohms) |
| Frequency Stability | ±5 ppm (-20°C to +60°C) |
| Receiver Sensitivity | 0.2 µV (12 dB SINAD) |
| Selectivity | 12 kHz (-6 dB), 30 kHz (-60 dB) |
| Intermodulation Rejection | 70 dB typical |
| Spurious Emissions | Less than -60 dB |
| Cleaning Instructions | Use a soft, dry cloth. Do not use harsh chemicals. |
| Safety Warnings | Do not operate with damaged antenna; avoid exposure to high RF levels. |
| Spare Parts Availability | Contact Yaesu authorized dealers for replacement parts. |
Frequently Asked Questions - FT-2980R YAESU
How do I program memory channels on the FT-2980R?
To program a memory channel, select the desired frequency, press and hold the F key, then press the MR key. Use the dial to select a memory channel number, then press the PTT key to store.
What power settings are available?
The FT-2980R offers three power levels: High (80W), Medium (30W), and Low (10W). Press the F key, then the LOW button to cycle through them.
How can I set the CTCSS/DCS tones?
Press the F key, then the TONE key to cycle through tone modes: TONE, T SQL, DCS. For CTCSS, select TONE or T SQL, then press F + CODE to adjust the tone frequency using the dial.
Does the FT-2980R support wide or narrow FM?
Yes, the FT-2980R supports both Wide (25 kHz) and Narrow (12.5 kHz) FM operation. To switch, press and hold the F key, then press the D/W button.
What is the maximum transmitting current draw?
At high power (80W) output, the current draw is approximately 13A from a 13.8V DC supply. Ensure your power source can handle this.
How do I perform a factory reset?
Turn off the radio, then press and hold the F and V/M keys simultaneously while turning the power back on. The display will show 'RESET'. Release the keys and press the F key to confirm.
Can I use the FT-2980R as a base station?
Yes, you can use it as a base station with a suitable 13.8V DC power supply and an external antenna. The mobile mount can be removed for desktop use.
What antenna connector does the FT-2980R have?
The antenna connector is a standard SO-239 (female UHF) type. Use a PL-259 plug with 50 ohm coax cable.
How do I enable the automatic squelch?
Press the F key, then the SQL key to enable automatic squelch (ASQ). ASQ opens when a carrier with the set tone is detected.
What safety precautions should I take when installing?
Ensure the radio is connected to a fused 13.8V DC supply. Avoid installing where it may obstruct airbags or driving vision. Do not transmit without an antenna connected to prevent damage.
User questions about FT-2980R YAESU
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Talkie Walkie in PDF format for free! Find your manual FT-2980R - YAESU and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. FT-2980R by YAESU.
USER MANUAL FT-2980R YAESU
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : YAESU
Model : FT-2980R
Category : Talkie Walkie