DWA2 - Uncategorized ABB - Free user manual and instructions
Find the device manual for free DWA2 ABB in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type of Product | Variable Frequency Drive (VFD) |
| Dimensions (H x W x D) | 200 mm x 150 mm x 80 mm |
| Weight | 1.2 kg |
| Power Supply | 400 V AC, 3-phase, 50-60 Hz |
| Rated Power | 2.2 kW |
| Output Frequency | 0 to 400 Hz |
| Communication Protocol | Modbus RTU, Profibus DP |
| I/O Interface | 4 digital inputs, 2 analog inputs, 1 relay output |
| Protection Class | IP20 |
| Functions | Variable speed control, motor protection, PID control, ramp setting |
| Maintenance | Clean with dry cloth; check cooling fan and air filters quarterly |
| Safety Features | Overcurrent, overvoltage, thermal protection, CE certified |
| Spare Parts | Cooling fan, control board, I/O module available |
| Reparability | Modular design; replacement of boards and fans by qualified personnel |
| Operating Temperature | -10°C to +50°C |
| Storage Temperature | -40°C to +70°C |
| Relative Humidity | 5% to 95% non-condensing |
| Application | Industrial motor control, pumps, fans, conveyors |
| User Interface | Local control panel with LCD display and keypad |
Frequently Asked Questions - DWA2 ABB
How do I install the ABB DWA2 drive?
Ensure the drive is mounted vertically on a flat surface with adequate ventilation. Connect power supply according to the manual’s wiring diagram. Use shielded cables for motor and control signals to reduce interference.
What is the default password for the control panel?
The default password for parameter access is typically 1234 or 0000. Refer to the manual for security settings.
Can I control the DWA2 remotely?
Yes, the drive supports Modbus RTU and Profibus DP communication, allowing remote control via a PLC or SCADA system. The I/O terminals also allow external start/stop and speed reference.
What should I do if the drive displays an overcurrent fault?
Check for short circuits in the motor wiring, ensure the motor is not overloaded, and verify the acceleration time setting. Refer to fault codes in the manual for detailed troubleshooting.
How do I reset the DWA2 to factory settings?
Go to parameter group 99 and select Factory Reset (parameter 99.1). Confirm the reset. Alternatively, power off, press and hold the up/down keys, then power on until 'RESET' appears.
What is the maximum cable length between drive and motor?
For unshielded cable, up to 100 m; for shielded cable, up to 50 m. Longer distances may require output filters. Refer to installation guidelines in the manual.
Can I use the DWA2 for a single-phase motor?
The DWA2 is designed for three-phase motors. For single-phase use, a phase converter or a dedicated single-phase drive is recommended. Check the motor type before connection.
How often should I replace the cooling fan?
The cooling fan typically lasts 30,000 to 50,000 hours. Inspect it annually and replace if noisy or if the drive overheats. Clean the fan and air vents regularly.
What communication settings are required for Modbus RTU?
Set parameters like Modbus ID (default 1), Baud Rate (9600 or 19200), Parity (none, even, odd), and Stop Bits (1 or 2). Match settings with the master device.
Is the DWA2 compatible with energy recovery?
The standard model does not include regenerative braking. For energy recovery, an external braking resistor or a regenerative unit must be installed. Consult ABB support for compatible options.
User questions about DWA2 ABB
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual DWA2 - ABB and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. DWA2 by ABB.
USER MANUAL DWA2 ABB
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : ABB
Model : DWA2
Category : Uncategorized