PA-R100 - Receiver TASCAM - Free user manual and instructions
Find the device manual for free PA-R100 TASCAM in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Stereo Receiver |
| Power Output | 100W per channel (8 ohms, 20Hz-20kHz, 0.05% THD) |
| Total Harmonic Distortion | < 0.05% |
| Frequency Response | 20Hz - 20kHz (±0.5dB) |
| Signal-to-Noise Ratio | 85dB (line) |
| Input Sensitivity | 150mV (line) |
| Inputs | 4x Line, 1x Phono (MM), 1x Tuner, 1x Tape Monitor |
| Outputs | 2x Speaker (A/B), 1x Headphone (6.3mm), 1x Tape Rec |
| Speaker Impedance | 4-16 ohms |
| FM Tuner Section | FM stereo, 87.5-108MHz, 50dB quieting sensitivity 15µV |
| AM Tuner Section | AM mono, 530-1710kHz |
| Dimensions (W x H x D) | 435 x 140 x 350 mm |
| Weight | 8.5 kg |
| Power Supply | AC 230V, 50/60Hz |
| Power Consumption | 250W (max) |
| Material | Metal chassis, aluminum front panel |
| Cleaning Instructions | Wipe with a dry, soft cloth. Do not use solvents. |
| Safety Features | Overload protection, short-circuit protection, thermal shutdown |
| Spare Parts Availability | Contact Tascam service center for genuine parts |
Frequently Asked Questions - PA-R100 TASCAM
How do I connect speakers to the PA-R100?
Use the speaker terminals on the back panel. Connect the left channel to the left terminal and right channel to the right terminal. Ensure impedance is between 4 and 16 ohms. Use the A or B speaker selectors on the front panel.
Can I use the PA-R100 with a turntable?
Yes, the PA-R100 has a dedicated phono input for moving magnet (MM) cartridges. Connect your turntable to the PHONO jacks and ensure the ground wire is attached to the ground terminal.
What should I do if there is no sound from the speakers?
Check that the speaker wires are properly connected, the speaker selector is on, the volume is turned up, and the source is selected correctly. Also verify that the mute function is not activated and that the protection circuit has not tripped.
How do I clean the PA-R100?
Unplug the unit and wipe the exterior with a dry, soft cloth. Do not use alcohol, thinner, or abrasive cleaners. For vents, use a soft brush or vacuum cleaner on low suction.
What is the power output of the PA-R100?
The PA-R100 delivers 100 watts per channel into 8 ohms, with both channels driven, from 20Hz to 20kHz with less than 0.05% THD.
Can I connect headphones to the PA-R100?
Yes, there is a 6.3mm headphone jack on the front panel. When headphones are plugged in, the speaker outputs are automatically muted.
How do I set the FM tuner?
Press the FM button on the front panel. Use the tuning knob to search for stations. For preset memory, refer to the manual for storing frequencies.
What types of audio sources can I connect?
The PA-R100 has multiple inputs: LINE (for CD players, etc.), PHONO (turntable), TUNER, and TAPE MONITOR (for tape decks). It also has a tape output for recording.
Is the PA-R100 safe to use with 4 ohm speakers?
Yes, the PA-R100 is rated for 4 to 16 ohms. However, continuous operation at very high volume with 4 ohm loads may cause the amplifier to overheat. Ensure adequate ventilation.
Where can I find replacement parts or service?
For genuine Tascam spare parts and authorized service, contact your local Tascam distributor or visit the Tascam support website. Do not attempt internal repairs yourself.
User questions about PA-R100 TASCAM
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual PA-R100 - TASCAM and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. PA-R100 by TASCAM.
USER MANUAL PA-R100 TASCAM
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : TASCAM
Model : PA-R100
Category : Receiver