DWS-3024L - Controller D-LINK - Free user manual and instructions
Find the device manual for free DWS-3024L D-LINK in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Wireless LAN Controller |
| Model Number | DWS-3024L |
| Brand | D-Link |
| Form Factor | Rack-mountable (1U) |
| Dimensions (WxDxH) | 440 x 250 x 44 mm |
| Weight | 3.5 kg |
| Power Supply | AC 100-240V, 50/60 Hz |
| Power Consumption | 30W (maximum) |
| Number of Managed Access Points | Up to 24 |
| Management Ports | 1x RJ-45 console, 1x 10/100/1000 Ethernet |
| Wireless Standards Supported | 802.11a/b/g/n/ac |
| Security Features | WPA/WPA2, 802.1X, MAC filtering, rogue AP detection |
| Management Interface | Web-based GUI, CLI, SNMP |
| Operating Temperature | 0°C to 40°C |
| Storage Temperature | -20°C to 70°C |
| Humidity | 10% to 90% non-condensing |
| Certifications | CE, FCC, RoHS |
Frequently Asked Questions - DWS-3024L D-LINK
How do I access the web interface of the DWS-3024L?
Connect a computer to the same network as the controller. Open a web browser and enter the default IP address (192.168.0.100) or the IP assigned via DHCP. Log in with default credentials (admin/admin). It is recommended to change these after initial setup.
Can I manage third-party access points with this controller?
No, the DWS-3024L is designed to manage only D-Link access points that support the D-Link Wireless Management Protocol (DWMP). Using third-party APs may not work or may cause compatibility issues.
How do I reset the controller to factory defaults?
Locate the reset button on the front panel. Use a paperclip to press and hold the button for about 10 seconds until the LED blinks. The device will reboot with factory settings. Note that all configurations will be lost.
What is the maximum number of access points I can manage?
The DWS-3024L can manage up to 24 D-Link access points. For larger deployments, consider the DWS-4026 or a higher-end model.
How do I update the firmware?
Download the latest firmware from D-Link's support website. Then log into the web interface, navigate to System > Firmware Upgrade, and upload the file. Do not power off the device during the upgrade.
Does the controller support mesh networking?
No, the DWS-3024L does not support mesh networking. It requires wired connections to access points. For mesh capabilities, look at D-Link's DWS-4000 series controllers.
What are the default IP and login credentials?
The default IP is 192.168.0.100, username: admin, password: admin. If the device is on a network with DHCP, it may get a different IP. Check your router's DHCP lease list if needed.
How can I back up my configuration?
In the web interface, go to System > Backup/Restore. Click 'Backup' to download a config file. To restore, upload the saved file. Keep backups for disaster recovery.
What should I do if the controller is overheating?
Ensure the device is in a well-ventilated area and not stacked with other equipment. Check that fans are working. Operating temperature should be between 0°C and 40°C. If overheating persists, contact D-Link support.
Is the DWS-3024L compatible with 802.11ax (Wi-Fi 6) access points?
No, the DWS-3024L was designed for earlier wireless standards (802.11a/b/g/n/ac). It may not fully support 802.11ax features. For Wi-Fi 6, use a newer controller like the DWS-6000 series.
User questions about DWS-3024L D-LINK
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Controller in PDF format for free! Find your manual DWS-3024L - D-LINK and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. DWS-3024L by D-LINK.
USER MANUAL DWS-3024L D-LINK
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : D-LINK
Model : DWS-3024L
Category : Controller