RL38T600ESA - Refrigerator SAMSUNG - Free user manual and instructions

Product Type	French Door Refrigerator Freezer
Brand	Samsung
Model	RL38T600ESA
Dimensions (H x W x D)	192.5 x 91.2 x 71.7 cm
Weight	110 kg
Power Supply	220-240 V, 50 Hz
Energy Class	E
Cooling Technology	Twin Cooling Plus, No Frost
Lighting	LED
Shelves	Tempered glass, height-adjustable
Vegetable Drawer	With humidity control
Water and ice dispenser	Built-in (water filter included)
Door Alarm	Yes
Holiday Mode	Yes
Defrost	Automatic
Maintenance	Clean the interior and gaskets with a soft cloth and soapy water. Do not use abrasive products.
Safety	Child lock (depending on version)
Spare Parts	Available on the Samsung website and from authorized services
Repairability	Repairability index: 8.6/10
Warranty	2 years

Frequently Asked Questions - RL38T600ESA SAMSUNG

How to set the refrigerator and freezer temperature?

Use the control panel on the front. Press Fridge or Freezer to select the zone, then adjust the temperature using the + or - buttons. The recommended range is 3-5°C for the refrigerator and -18°C for the freezer.

What to do if the water dispenser does not flow?

Check that the water filter is correctly installed and not clogged. Make sure the water supply line is open. If the problem persists, remove and reinsert the filter, or contact customer service.

How to change the water filter?

Open the filter cover (usually at the top right). Turn the old filter counterclockwise to unlock it and pull it down. Insert the new filter, turn clockwise until it stops, then run 2-3 liters of water to flush the system.

Why is there frost in the freezer despite No Frost?

The No Frost system minimizes frost, but accumulation can occur if the door is not properly closed or opened frequently. Check the seal tightness and ensure food does not block the cold air intake.

How to activate holiday mode?

Press the Vacation button (or hold it down depending on the model). Holiday mode sets the refrigerator to a higher temperature (about 7°C) to save energy while preserving a small amount of food. The freezer remains normal.

How to clean the door gasket?

Use a soft cloth dampened with warm water and mild soap. Gently rub the gasket to remove residues. Avoid harsh chemicals that could damage the rubber. Dry thoroughly after cleaning.

What to do if the door alarm sounds?

The alarm triggers if the door remains open for more than 2 minutes. Close the door fully to stop it. If the alarm continues, check that an object is not preventing closure. If the problem persists, contact technical service.

How to install the ice maker?

The ice maker is usually built-in. Make sure the water dispenser is connected and the water filter is in place. In the menu, activate Ice Maker. The first ice cubes may be small; the system adjusts after a few cycles.

What to do if the refrigerator is not cooling well?

Check that the set temperature is correct. Ensure air inlets are not blocked by food. Clean the condenser coils at the back (if accessible). If the problem persists, the compressor or refrigerant may be faulty; contact a professional.

How to reverse the door opening direction?

Reversing is complex and requires tools. Remove the upper and lower hinges, transfer the hinge plates to the other side, then reposition the doors. It is recommended to call an authorized technician to avoid damage.

USER MANUAL RL38T600ESA SAMSUNG

User servicing manual

1. You can check where to buy replacement parts at http://samsung.com
2. Visit the part purchase site and enter the model code of your product to check the parts available for purchase. The model code is labelled on the outer side of your product.
3. You can check the model code and version on the barcode label at the bottom left of the product.
4. For replacement parts, make sure the part name matches that of the illustration in this manual.
5. User-serviceable parts are limited to handles (some models only), gaskets, drawers, and hinges.

NOTE

Following the repair by a non-authorised service provider, self-repair or non-professional repair of the product, Samsung is not liable for any damage to the product, any injury or any other product safety issue caused by any attempt to repair the product which does not carefully follow these repair and maintenance instructions. Any damage to the product caused by an attempt to repair the product by any person other than a Samsung certified service provider will not be covered by the warranty.

CAUTION

• The part name listed on the site may differ from that in this manual. Please make sure you choose the right part name.
• Replacing hinges requires extreme caution because it involves detaching the door.
• Be sure to wear safety gloves while making repairs.

English

The actual image and provided parts of the refrigerator may differ, depending on the model and the country.

01 Top hinge 02 Gasket 03 Drawer 04 Handles (Applicable models only) 05 Middle hinge 06 Barcode label 07 Bottom hinge

English

Handle replacement

Model name looks like this: RB38**6****, RB38**2****, RL38**6****, RB3L**2****, RB36**6****, RB36**2****, RL36**6****, RL36**2****, RB34**6****, RB34**2****, RL34**6****, RL34**2****

What replaces the asterisks may differ depending on the model.

Asterisk(s) in the model code indicate a variant model and may replace (0-9) or (A-Z) in the model code.

CAUTION

• When replacing the door handle, take care not to scratch the front of the door.
• Firmly press the handles at the supports. Make sure there is no gap between the supports and the door.
• Tightly fasten the screws when attaching the handle.
• Check that the handle is firmly attached before using the product.

Tools required (not provided)

Phillips screwdriver Flat-head screwdriver

To detach the handles

NOTE

This procedure applies to both the fridge and freezer compartment.

1. Use a flat-head screwdriver to remove the screw covers.
2. After detaching the handle, attach the screw covers back on the screw holes.
3. Use a Phillips screwdriver to remove the screws and detach the handle.

NOTE

Use these screws to fasten the handle on the opposite side.

1. Assemble the new handle in the reverse order of disassembly.

English

Gasket replacement

CAUTION

Make sure you firmly attach the gasket. Otherwise, cold air from the refrigerator may leak.

To remove the gasket

Open the door and remove the gasket from the door.

To replace the gasket

Attach a new gasket to the refrigerator door. Make sure there is no gap between the new gasket and the door.

Drawer replacement

CAUTION

Check that the drawer is inserted properly into the rail during assembly.

To remove the drawer

Gently lift up the front of the drawer and slide it out.

To reattach the drawers

Reattaching the drawers follows the reverse order of their respective removal steps.

English

Hinge replacement

To replace the hinges, you must remove the doors first.

CAUTION

- When removing the doors, take extreme caution because the doors are heavy. - Before replacing the hinges, put a soft pad such as cardboard on the floor to prevent scratches on the door when you place the doors down. - As the hinges must be handled carefully and replaced by two or more persons, we recommend you to call for professional technical service.

- If you remove the hinge without holding the door, the door may fall and cause injury. - Ensure that the shaft is firmly tightened on the hinge. - Check that the hinge is firmly attached to the cabinet. - Make sure the wire connectors are connected properly. - Be careful not to damage the wires when fastening the top cover.

WARNING

- Tilting/laying the refrigerator requires a minimum of 2 people. - Disconnect the power cord before reversing the doors.

Tools required (not provided)

Phillips screwdriver, flat-head screwdriver, 11 mm spanner

10 mm socket wrench, 8 mm socket wrench, 10 mm spanner

English

Reversing the door

NOTE

For models with handles, reverse the handles first. (For detailed information, see the "Handle replacement (For models with bar handles)" section.)

1. With the fridge door closed, use a Phillips screwdriver to remove the screws fastening the top cover (A).
2. Gently lift the top cover (A) and place it on top of the refrigerator.

- Be careful when lifting the top cover (A). There is a wire connected underneath it.

1. Remove the wire and the wire connector placed on the holder underneath the top cover.

- This step may not apply to some models.

CAUTION

Do not pull the connectors too hard.

1. Disconnect the wire connector (A).
2. This step may not apply to some models.

1. Use a socket wrench (8 mm) to remove the screws fastening the top hinge (A).

CAUTION

To prevent the fridge door from falling, make sure to hold it tight while removing the screws.

1. Open the fridge door, and then lift the door to remove it from the middle hinge. Keep the door in a safe place.

CAUTION

The door is heavy. To prevent damage or injury, use caution while removing the door.

1. Open the freezer door, and then use a socket wrench (8 mm) to remove the screws fastening the bottom hinge (A).

1. With the freezer door sitting on the bottom hinge (A), slowly pull the bottom hinge (A) to remove it from the holder on the bottom of the refrigerator. Once the bottom hinge (A) is removed from the holder, remove it from the freezer door, and then pull the freezer door down to remove it from the middle hinge (B).

CAUTION

To prevent the freezer door from falling, make sure to hold the freezer door tight until it is safely removed from the middle hinge (B).

1. Use a Phillips screwdriver and socket wrench (10 mm) to remove the screws fastening the middle hinge (A).
2. Reassemble in the opposite order of disassembly after replacing the top, middle, and/or bottom hinge.

CAUTION

• Make sure the wire connectors are connected properly.

- Be careful not to damage the wires when fastening the top cover

English

Repair guide

Phillips screwdriver Flathead screwdriver

Phillips screwdriver Flathead screwdriver

Removing the handles

NOTE

Phillips screwdriver Flathead screwdriver

Open the door and remove the gasket from it.

Installing the gasket

01 Upper hinge 02 Door gasket 03 Drawer 04 Handles (only certain models) 05 Middle hinge 06 Barcode label 07 Lower hinge

Serbian

Replacing the handle

The model name looks like this: RB38**6****, RB38**2****, RL38**6****, RB3L**2****, RB36**6****, RB36**2****, RL36**6****, RL36**2****, RB34**6****, RB34**2****, RL34**6****, RL34**2****

The content that replaces the asterisks may vary depending on the model.

The asterisks in the model code indicate the model variant and may be replaced by digits (0–9) or letters (A–Z).

CAUTION

• When replacing the handle on the door, be careful not to scratch the front of the door.
• Press the handles firmly onto the supports. Make sure there is no gap between the supports and the door.
• Tighten the screws firmly when installing the handle.
• Before using the product, check that the handle is properly attached.

Required tools (not provided)

Open the door and remove the door gasket from it.

To replace the door gasket

Install the new door gasket on the refrigerator door. Make sure there is no gap between the new gasket and the door.

Replacing the drawer

CAUTION

During installation, check that the drawer is properly inserted into the guides.

To remove the drawer

Gently lift the front of the drawer upward and pull it out.

To replace the drawer

1. With the refrigerator doors closed, use a Phillips screwdriver to remove the screws securing the top cover (A).
2. Carefully lift the top cover (A) and place it on top of the refrigerator.

- Be careful when lifting the top cover (A). There are connected cables underneath.

1. Remove the cable and cable connector from the holder located under the top cover.

- This step does not apply to all models.

CAUTION

1. While the freezer door rests on the lower hinge (A), slowly pull the lower hinge (A) to remove it from the holder on the bottom of the refrigerator. Once the lower hinge (A) is removed from the holder, remove it from the freezer door, then pull the freezer door downward to detach it from the middle hinge (B).

! CAUTION

01 Top hinge 02 Gasket 03 Drawer 04 Handles (only on certain models) 05 Middle hinge 06 Barcode label 07 Bottom hinge

Croatian

Replacing the handles

The model name looks like this: RB38**6****, RB38**2****, RL38**6****, RB3L**2****, RB36**6****, RB36**2****, RL36**6****, RL36**2****, RB34**6****, RB34**2****, RL34**6****, RL34**2****

1. Use a flat-head screwdriver to remove the screw covers.
2. After detaching the handle, attach the screw covers back onto the screw holes.
3. Use a Phillips screwdriver to remove the screws and detach the handle.

NOTE

Use the specified screws to attach the handle to the opposite side.

1. Assemble the new handle in the reverse order of detachment.

Croatian

Replacing the gasket

CAUTION

Make sure to firmly attach the gasket. Otherwise, cold air from the refrigerator could escape.

To remove the gasket

Open the door and remove the gasket from the door.

To replace the gasket

Carefully lift the front part of the drawer and pull it out.

Reinstalling the drawers

1. Using a ratchet wrench (8 mm), remove the screws that secure the upper hinge (A).

CAUTION

To prevent the door from falling, hold it firmly while removing the screws.

01 Upper hinge 02 Gasket 03 Drawer 04 Handles (only on models that have them) 05 Middle hinge 06 Barcode label 07 Lower hinge

Albanian

Phillips screwdriver Flathead screwdriver

Cross-head screwdriver Flat-head screwdriver

Open the door and remove the gasket from the door.

To replace the gasket

Open the door and remove the gasket from the door.

Replacing the gasket

Attach the new gasket to the refrigerator door. Make sure there are no gaps between the new gasket and the door.

Replacing the drawer

CAUTION

Carefully lift the front of the drawer and pull it out.

Reinstalling the drawer

1. Keep the refrigerator door closed, then use a Phillips screwdriver to remove the screws securing the top cover (A).
2. Carefully lift the top cover (A) and place it on top of the refrigerator.