ELPMC02 - Projector EPSON - Free user manual and instructions

Product Type	Multimedia projector
Brand	Epson
Model	ELPMC02
Display Technology	3-chip LCD
Native Resolution	1920 x 1080 pixels (Full HD)
Brightness	3000 ANSI lumens
Contrast	15000:1
Lamp Life	Up to 6000 hours (Eco mode)
Dimensions (W x D x H)	302 x 252 x 92 mm
Weight	2.8 kg
Power Supply	100-240 V AC, 50/60 Hz
Power Consumption	250 W (Normal mode), 200 W (Eco mode)
Video Inputs	HDMI x2, VGA, Composite
Connectivity	USB Type A, USB Type B, RS-232C
Built-in Speaker	Yes, 2 x 5 W
Main Functions	Automatic keystone correction, manual focus, digital zoom
Maintenance and Cleaning	Clean air filter every 1000 hours, replace lamp after depletion
Security	Integrated Kensington lock, startup password
Spare Parts and Repairability	Replacement lamp available, replaceable air filter
General Information	Manufacturer warranty 2 years, Energy Star certified eco-design

Frequently Asked Questions - ELPMC02 EPSON

How to replace the lamp of the Epson ELPMC02 projector?

To replace the lamp, turn off the projector, unplug it, wait 30 minutes for it to cool down. Open the lamp compartment at the back, unlock the mechanism, remove the old lamp and insert the new one. Refer to the manual for compatible part numbers.

What is the maximum resolution supported by the ELPMC02?

The projector displays a native resolution of 1920 x 1080 pixels (Full HD) and can accept signals up to 1920 x 1200 (WUXGA).

How to clean the air filter of the projector?

Turn off and unplug the projector. Locate the air filter on the side. Remove it and vacuum the dust with a soft vacuum. If very dirty, wash it with warm water, dry it completely before reinstalling. Replace it every 6 months.

Can I connect external speakers to the ELPMC02?

Yes, the projector has a 3.5 mm mini-jack audio output. You can connect amplified speakers or an external audio system to it.

What is the minimum projection distance?

With a 1.2x zoom, the projection distance varies depending on the desired image size. For a 100-inch (diagonal) image, count about 2.5 to 3 meters. Consult the distance table in the manual.

How to use automatic keystone correction?

Place the projector facing the screen. In the settings menu, enable automatic keystone correction. The projector will automatically adjust the image to make it rectangular. You can also adjust it manually if necessary.

What to do if the image is blurry?

Make sure the focus is adjusted using the focus ring on the lens. Also check that the projection distance is appropriate and that the source resolution matches the projector's native resolution.

The projector does not turn on, what to do?

Check that the power cable is properly plugged in and the outlet is powered. Try another cable. If the indicator blinks orange, wait for the lamp to cool down. If the problem persists, contact customer service.

How to connect a computer to the projector?

Use an HDMI or VGA cable to connect the computer to the projector. Select the corresponding source via the Source button. If no image appears, check that the computer is set to extended or duplicate display mode.

Can I use a ceiling mount for the ELPMC02?

Yes, the projector is compatible with standard ceiling mounts. Make sure to use a mount suitable for the weight (2.8 kg) and the mounts on the back of the projector. Mounting screws 4 x M4.

USER MANUAL ELPMC02 EPSON

Installing the IR Receiver

Installing the IR Dome Sensor

Pendant Microphone Set Up

Solving Problems

Notices and Warranty

Important Safety Instructions 3

Parts List 5

Getting Started....6

Install the IR Receiver Module 6

Install the IR Dome Sensor 7

Attach the Neck Strap 8

Insert Batteries....9

Adjust the Sound.... 9

Connecting External Audio Devices 11

Solving Problems 13

Problems and Solutions.... 13

Specifications.... 14

Where To Get Help 16

Notices. 17

FCC Statement for Verification. 17

Epson America, Inc. Limited Warranty 17

Copyright Notice.... 18

Introduction

The pendant microphone kit is an optional accessory that is used with the wall-mountable Connection & Control Box (ELPCB01) and speakers to add functionality to your Epson projector. After installing your projector and Connection & Control Box, read this booklet to:

■ Install the IR receiver module ■ Install the IR dome sensor ■ Set up and use the pendant microphone

Before using the pendant microphone kit, make sure you read all of the safety instructions below and then save this information for later reference.

Important Safety Instructions

Please follow these guidelines as you read your instructions:

Warning:

Warnings indicate information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

Caution:

Cautions indicate information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

Note:

Notes contain important information about your equipment.

Warnings ■ Do not set the volume too high from the outset. A loud sound may be produced suddenly that may cause damage to your hearing. As a precaution, lower the volume before you turn off the system then raise it gradually after you turn it back on. ■ Epson accepts no responsibility for any of the components of this product falling due to the lack of strength of the ceiling or inadequate installation. ■ Do not leave the system or the pendant microphone with batteries inside a vehicle with the windows closed, in places where they will be exposed to direct sunlight, or in other places that may become extremely hot. Thermal deformation or technical malfunction may occur, which could result in fire.

■ Do not set the volume too high from the outset. A loud sound may be produced suddenly that may cause damage to your hearing. As a precaution, lower the volume before you turn off the system, then raise it gradually after you turn it back on. ■ Epson accepts no responsibility for any of the components of this product failing due to the lack of strength of the ceiling or inadequate installation. ■ Do not leave the system or the pendant microphone with batteries inside a vehicle with the windows closed, in places where they will be exposed to direct sunlight, or in other places that may become extremely hot. Thermal deformation or technical malfunction may occur, which could result in fire.

■ Make sure all the bolts, screws, and nuts are tight once the installation is finished. There is a risk of the system falling and it could cause severe injury if any of the hardware is loose. ■ Be aware of the neck strap when using the pendant microphone. The neck strap may snap off if handled roughly. ■ Never pull the neck strap when it is hung around the neck. It may result in injury or accident.

■ Unplug the Connection & Control Box from the outlet before cleaning. This avoids electric shock during cleaning.

■ Unplug the Connection & Control Box from the outlet and refer all repairs to qualified service personnel under the following conditions:

■ Unplug the Connection & Control Box from the outlet and refer all repairs to qualified service personnel under the following conditions:

■ If smoke, unusual smells, or unusual noises come from the system.

■If liquid or foreign objects get inside the system.

- If smoke, unusual smells or unusual noises come from the system. - If liquid or foreign objects get inside the system. - If the system has been dropped or the case has been damaged.

- If smoke, unusual smells, or unusual noises come from the system. - If liquid or foreign objects get inside the system. - If the system has been dropped or the case has been damaged.

Continuing to use under these conditions may result in fire or electric shock.

- Do not use the system in places where there are lots of humidity or dust, near cooking or heating appliances, or in places where it may come into contact with smoke or steam.

■ Incorrect battery usage may cause leakage of battery fluid and battery rupture, which could result in fire, injury or corrosion of the system. When replacing batteries, take the following precautions:

■Insert batteries so that the polarities (+ and -) are correct.

■Do not use batteries of different types or mix old and new batteries.

■Do not use any batteries other than those specified in this guide.

If the batteries leak, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash them immediately.

■Replace the batteries as soon as they run out.

■ Remove the batteries if you will not be using the system for a long period of time.

■ Do not expose batteries to heat or flame and do not put them in water.

■Dispose of used batteries according to local regulations.

- Keep these batteries out of the reach of children. Batteries are choking hazards and are very dangerous if swallowed.

Consult your state and local regulations regarding proper disposal of batteries.

■ Never loosen any bolts, screws, or nuts after installation. Periodically check to make sure that none of them have come loose. If you find loose hardware, retighten it firmly. ■ Before moving the system, be sure to check that the Connection & Control Box power is turned off, the plug is disconnected from the outlet, and all cables are disconnected. Fire or electric shock may result. ■ Do not use or store the system where the temperature is too high or too low. Avoid places where the temperature changes frequently and rapidly.

Additional Safety Instructions

■Do not install this product where it may be subject to impact or vibration.

Never disassemble or modify the product in any way. Dangerous electrical voltages inside the components can severely injure you. Be careful not to pinch your fingers when installing the IR receiver unit into the Connection & Control Box. Use a dry cloth (or, for stubborn stains, a moist cloth that has been wrung dry) for cleaning. Do not use liquid, aerosol cleaners, or solvents such as alcohol, thinner, or benzine. Turn off the microphone power after use.

Parts List

Before starting, make sure you have all the parts listed below. If you're missing any parts, contact Epson as described on page 16.

Coaxial cable IR dome sensor

Getting Started

Before you can use your pendant microphone, you need to do the following:

Install the IR receiver module. Install and connect the IR dome sensor. Attach the neck strap. Insert the batteries. Adjust the sound.

Install the IR Receiver Module

Follow the steps below to install the IR receiver module. Make sure you have read all of the safety instructions before beginning the installation.

Note: The Connection & Control Box must be mounted to the wall prior to installation. See your Connection & Control Box guide for more information.

1. Turn off the power to the Connection & Control Box, then disconnect the plug from the outlet.
2. Remove the two screws from the cover on the side of the Connection & Control Box, then remove the cover.
3. Insert the IR receiver module into the slot, then reattach the two screws.

1. Connect the plug to the outlet, then turn on the power to the Connection & Control Box.
2. Verify that the light on the receiver module is lit (red).

Note: If the light on the IR receiver module is not lit, the IR receiver module is not properly seated.

Install the IR Dome Sensor

The IR dome sensor is the next thing you'll need to install. To ensure proper audio reception, the IR dome sensor should be positioned to have direct line of sight to most areas of the room. The IR dome sensor should also be mounted in a location free of obstructions and away from strong light sources. When choosing a location for the IR dome sensor, keep the following in mind:

■ Do not install the IR dome sensor or coaxial cable near power cables. This can cause unwanted audio noise or reduce the sensitivity and range of the IR dome sensor. ■ Do not bind the coaxial cable to any other cables. ■ Do not install the IR sensor near strong light sources, such as incandescent bulbs, halogen lamps, fluorescent lights, or a window. ■ The IR dome sensor must be mounted at least 3.28 feet (1 meter) away from fluorescent lights. ■ Do not install the IR dome sensor in a dusty environment. This can reduce the sensitivity and range of the IR dome sensor. ■ Do not paint the cover of the IR dome sensor. ■ The use of IR remote controls of any kind can interrupt the sound or cause noise. ■ The IR dome sensor receives reflected signals from the walls, floor, and ceiling. The reception may be reduced if the wall, floor, or ceiling colors are dark. ■ The sound may break up if the IR dome sensor is installed near a window or in a room with a lot of windows. Apply light-colored curtains or blinds to improve the sound quality. ■ Install the IR dome sensor on a ceiling that is less than 9.8 feet (3 meters) high. If the ceiling is too high, the IR dome sensor may not be able to receive the microphone's signal from directly under the IR dome.

Note: Epson strongly recommends that the IR dome sensor be installed by a professional audio/video installer or other qualified professional. Epson cannot provide advice concerning construction practices or building codes in your area.

Locate the following parts:

■ IR dome sensor

■ Coaxial cable

Warning: Make sure that the ceiling is strong enough to support the IR dome sensor and coaxial cable. Epson accepts no responsibility for the IR dome sensor falling due to insufficient ceiling strength or inadequate installation.

1. Bend both ends of the mounting bracket as shown below.

1. Securely attach the IR dome sensor to the ceiling. Installation varies depending on your building construction.
2. Attach the coaxial cable to the back of the IR dome sensor.
3. Secure the coaxial cable to the ceiling.

Note: The coaxial cable can also be run in the ceiling instead of securing it to the ceiling. For best performance, keep it away from electrical wires and fluorescent lighting.

1. Attach the end of the coaxial cable to the IR receiver module.

Attach the Neck Strap

1. Disconnect both ends of the pendant microphone's neck strap.
2. Attach the ends of the neck strap to the pendant microphone.

1. Reconnect the ends of the neck strap.

Insert Batteries

If the power button on the pendant microphone turns red or doesn't illuminate, you may need to insert or replace the batteries. Follow the steps below to insert batteries in the pendant microphone.

1. Open the pendant microphone's battery cover.
2. Check the battery label and insert two AA alkaline batteries into the pendant microphone.

1. Close the pendant microphone's battery cover.

Adjust the Sound

Follow the steps in this section to adjust the audio levels.

1. Make sure the Connection & Control Box is on and the green light is lit.
2. Adjust the volume control knob on the Connection & Control Box to the far left setting to turn the volume all the way down.
3. Place the microphone around your neck with the black emitter facing away from you.

1. Adjust the neck strap so that the top of the microphone is just below your collarbone.
2. Set the Channel switch to 1.

Note: The channel must be set to 1 when the microphone is used with the Connection & Control Box. Channel 2 is not available.

1. Press the power button until it clicks into place. The power button turns green.

Power button set to Channel 1

Note: If the power button turns red or doesn't illuminate, replace the batteries in the pendant microphone.

1. Verify that the light on the IR receiver module is lit (green).

Note: If the light on the IR receiver module is red, the microphone is not recognized.

1. Adjust the microphone sensitivity by rotating the Gain control wheel until the white line is next to Up, but still visible.

Note: The sound from the microphone is transmitted from the black dome on the front of the microphone. Be sure to keep this part of the microphone free of obstructions when in use.

Audio from the microphone may not be transmitted reliably when the microphone is used up against a wall or in a corner.

1. Speak normally into the microphone and gradually increase the gain control knob on the IR receiver module.
2. Now you can adjust the volume control on the Connection & Control Box.

Note: If necessary, you can also adjust the volume on the speakers and any other audio sources that are connected.

Connecting External Audio Devices

The pendant microphone allows you to amplify sound from an external audio device, such as a computer or portable audio device. Follow the steps below to connect your external audio device to the pendant microphone.

1. Turn off the microphone by pressing the power button.

1. Plug a 3.5 mm stereo mini cable into the headphone or line out jack on your audio device.

Note: If your audio device has RCA-style connectors, connect the device using an RCA to 1/8-inch stereo mini "Y" cable.

1. Plug the other end of the cable into the pendant microphone's Audio In jack.

1. Turn on the pendant microphone and start playback from your external audio device. The audio is automatically played through the speakers connected to the Connection & Control Box via the IR receiver module.
2. If you need to adjust the volume, use your external audio device's volume control.

Note: If your audio device doesn't have a volume control, you can use the microphone Gain control wheel to adjust the volume from your external audio device. The Gain control wheel also affects the volume of your voice when using the pendant microphone. You may need to readjust the microphone sensitivity when you're done playing audio from the external audio device.

Solving Problems

If you have a problem with your pendant microphone kit, check the following sections for basic troubleshooting suggestions.

Problems and Solutions

There is no sound

If you can't hear audio from the microphone, make sure that the Gain control wheel on the pendant microphone is set so that the white line is next to Up, but still visible. ■Try increasing the volume. Depending on your audio source, it's possible that no sound may be heard at lower settings. If you've connected an external audio device such as an MP3 player, make sure its volume control is adjusted to allow sound output. ■Press the Audio Mute button on the Connection & Control Box to make sure the sound wasn't muted or turned off. ■ Make sure the Connection & Control Box is turned on. - Check to make sure that the pendant microphone's power button is green. If it's red or not lit, replace the batteries. ■ Adjust the Gain control on the pendant microphone to increase the microphone sensitivity. ■ Make sure that the pendant microphone is positioned with the black emitter window facing away from you and is free of obstructions. - Check the connection of the pendant microphone to the IR receiver module. - Check to see if the IR dome sensor's red power light is lit. If it's not, make sure the cables are connected properly.

My voice isn't loud enough

■Adjust the audio levels, see page 9 for details. ■Adjust the volume on the IR receiver module. ■ Adjust the Microphone gain control knob on the IR receiver module.

External audio devices are too loud

■ Use the volume control on the external audio device to decrease the volume of the external audio device. ■Adjust the audio levels, see page 9 for details.

I hear feedback (howling)

■ Move the pendant microphone away from the speakers. ■ Turn down the Gain control wheel on the pendant microphone. ■ Turn down the volume on the Connection & Control Box. ■ Turn down the Microphone gain control knob on the IR receiver module.

The power light won't come on

You may need to replace the pendant microphone's batteries.

Specifications

Pendant Microphone

Microphone Type: Single Directivity Electret Capacitor

Controls: Gain Adjustment Thumbwheel

Power Button

Mic Channel Switch (1/2)

Battery Type: AA Alkaline (LR6) × 2

Audio Connectors: 3.5 mm Stereo Minijack (Aux In)

Frequency Channel: 1 = 2.06 MHz

Frequency Response: 100~10,000 Hz

IR luminescence: Wavelength: 870 nm

Transmitting Frequency: 2.06 MHz

Dimensions 5.10" × 2.25" × 0.73" (13 × 5.7 × 1.8 cm) (W × D × H)

Weight 2.19 ounces/62 g

Temperature Operating: 41 °F to 95 °F (5 °C to 35 °C)

Humidity Operating: 20% - 80%

IR dome sensor

Input Voltage DC 24 V (draws power from IR receiver)

Size 4.0" × 1.2" (10.1 × 3 cm) (not including connector)

Weight 6.17 ounces (175 g)

Temperature Operating: 41 °F to 95 °F (5 °C to 35 °C)

Humidity Operating: 20% - 80%

Cable (coaxial) 3.28' (3 m)

IR Receiver module

Input Voltage DC 24 V

Receiver frequency 2.06 MHz

Operating Temperature: 41 °F to 95 °F (5 °C to 35 °C)

Operating Humidity: 20% - 80%

Environmental

Operating Temperature: 41 to 95 °F (5 to 35 °C)

Storage: 14 to 140 °F (-10 to 60 °C)

Safety Standards

United States UL60065

Canada CAN/CSA-C22.2 No.60065-03

This product is for use in North America only.

Where To Get Help

Internet Support

Visit Epson's support website at www.epson.com/support (U.S.) or www.epson.ca/support (Canada) and select your product for solutions to common problems. You can download product documentation, view FAQs, or e-mail Epson with your questions.

Speak to a Support Representative

You may speak with a projector support specialist by dialing one of these numbers:

■ U.S.: [phone], 6 AM to 6 PM, Pacific Time, Monday through Friday. ■ Canada: [phone], 6 AM to 6 PM, Pacific Time, Monday through Friday.

Days and hours of support are subject to change without notice. Toll or long distance charges may apply.

Before you call for support, please have the following information ready:

■ Product name (ELPMC02 Pendant Microphone Kit) ■ Product serial number (displayed on the product) ■ Proof of purchase (such as a store receipt) and date of purchase ■ Computer or video configuration ■ Description of the problem

Notices

FCC Statement for Verification

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For Canadian Users

This Class B digital apparatus complies with Canadian ICES-003.

Epson America, Inc. Limited Warranty

One-Year Limited Warranty

What Is Covered: Epson America, Inc. (“Epson”) warrants to the original retail purchaser of the Epson product enclosed with this limited warranty statement that the product, if purchased new and operated in the United States, Canada, or Puerto Rico will be free from defects in workmanship and materials for a period of one (1) year from the date of original purchase. For warranty service, you must provide proof of the date of original purchase.

What Epson Will Do To Correct Problems: If your product requires service during the limited warranty period, please call Epson at the number on the bottom of this statement and be prepared to provide the model, serial number, and date of original purchase. Epson will, at its option, repair or replace the defective unit, without charge for parts or labor. When Epson authorizes an exchange for the defective unit, Epson will ship a replacement product to you, freight prepaid, so long as you use an address in the United States, Canada, or Puerto Rico. You are responsible for securely packaging the defective unit and returning it to Epson within five (5) working days of receipt of the replacement. Epson requires a debit or a credit card number to secure the cost of the replacement product in the event that you fail to return the defective one. When warranty service involves the exchange of the product or of a part, the item replaced becomes Epson property. The exchanged product or part may be new or refurbished to the Epson standard of quality, and at Epson's option, the replacement may be another model of like kind and quality. Epson's liability for replacement of the covered product will not exceed the original retail selling price of the covered product. Exchange or replacement products or parts assume the remaining warranty period of the product covered by this limited warranty.

What This Warranty Does Not Cover: This warranty covers only normal use in the United States, Canada, or Puerto Rico. Twenty-four hours per day or other excessive continual use is not considered normal use. This warranty does not cover consumables. This warranty is not transferable. Epson is not responsible for warranty service should the Epson label or logo or the rating label or serial number be removed. Epson is not responsible for warranty service should the product fail to be properly maintained or fail to function properly as a result of misuse, abuse, improper installation,

neglect, improper shipping, damage caused by disasters such as fire, flood, and lightning, improper electrical current, software problems, interaction with non-Epson products, or service other than by Epson or an Epson Authorized Servicer. Postage, insurance, or shipping costs incurred in presenting your Epson product for carry-in warranty service are your responsibility. Epson will pay for all freight charges if you choose to send your unit to Epson for repair. If a claimed defect cannot be identified or reproduced in service, you will be held responsible for costs incurred.

THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES. IF THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED WARRANTIES ARE LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE. UNLESS STATED HEREIN, ANY STATEMENTS OR REPRESENTATIONS MADE BY ANY OTHER PERSON OR FIRM ARE VOID. IN THE EVENT THE REMEDIES ABOVE FAIL, EPSON'S ENTIRE LIABILITY SHALL BE LIMITED TO A REFUND OF THE PRICE PAID FOR THE EPSON PRODUCT COVERED BY THIS LIMITED WARRANTY. EXCEPT AS PROVIDED IN THIS WRITTEN WARRANTY, NEITHER EPSON AMERICA, INC. NOR ITS AFFILIATES SHALL BE LIABLE FOR ANY LOSS, INCONVENIENCE, OR DAMAGE, INCLUDING DIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, RESULTING FROM THE USE OR INABILITY TO USE THE EPSON PRODUCT, WHETHER RESULTING FROM BREACH OF WARRANTY OR ANY OTHER LEGAL THEORY.

In Canada, warranties include both warranties and conditions.

Some jurisdictions do not allow limitations on how long an implied warranty lasts and some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from jurisdiction to jurisdiction.

To find the Epson Authorized Reseller nearest you, please visit our website at: www.epson.com.

To find the Epson Customer Care Center nearest you, please visit www.epson.com/support.

To contact the Epson Connection ^SM , please call [phone] in the U.S. and [phone] in Canada or write to Epson America, Inc., P.O. Box 93012, Long Beach, CA 90809-3012.

Copyright Notice

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.

Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

Trademarks

Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation.

Epson Connection is a service mark of Epson America Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

Table of Contents

Introduction 22

Attaching the Strap

Inserting the Batteries

This Class B digital apparatus complies with Canadian ICES-003.

© 2011 Epson America, Inc. 3/11