Fuze SFX WH - Lamp Elation - Free user manual and instructions
Find the device manual for free Fuze SFX WH Elation in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Type | Moving head wash/effect fixture |
| Light Source | LED, 100W |
| Beam Angle | 15° - 30° motorized zoom |
| Color Wheel | 9 dichroic filters + open |
| Pan Range | 540° |
| Tilt Range | 270° |
| Control Protocol | DMX512 |
| DMX Channels | 16 |
| Strobe Rate | 1-25 Hz |
| Dimmer | 0-100% linear |
| Power Consumption | 150W |
| Input Voltage | AC 100-240V, 50/60Hz |
| Dimensions (L×W×H) | 320 × 240 × 420 mm |
| Weight | 8.5 kg |
| Housing Material | High-impact ABS plastic |
| Cooling | Active fan |
| IP Rating | IP20 (indoor use only) |
| Noise Level | < 35 dB(A) |
| Operating Temperature | -10°C to 45°C |
| Mounting Options | Floor stand or hanging clamp |
| Included Accessories | Power cord, user manual |
| Cleaning Instructions | Use a soft dry cloth; avoid solvents |
| Safety Features | Safety cable attachment point, auto-off on overheat |
| Warranty | 2 years |
Frequently Asked Questions - Fuze SFX WH Elation
How do I connect the Fuze SFX WH to a DMX controller?
Use a 3-pin or 5-pin XLR cable to connect the DMX IN of the fixture to the DMX OUT of your controller. Ensure the DMX termination is enabled on the last fixture.
What is the default DMX starting channel?
The default is channel 1. You can change it via the control panel menu (SETUP > DMX Address).
How do I clean the lens?
Use a soft, lint-free cloth slightly dampened with water. Do not use alcohol or abrasive cleaners. Clean when the fixture is off and cool.
Can the Fuze SFX WH be used outdoors?
No, the fixture is rated IP20 for indoor use only. Exposure to moisture may damage the electronics.
How do I reset the fixture to factory defaults?
Go to the menu, select SETTINGS > FACTORY RESET, and confirm. The fixture will reboot with default settings.
Why is the fixture not responding to DMX?
Check the DMX cable connection, ensure the correct starting address is set, and verify that the controller is sending data. Try replacing the cable or using a terminator.
What type of power cord does it use?
It uses a standard IEC C14 connector. The included cord is for 100-240V AC, 50/60Hz.
How do I change the fuse?
Disconnect power. The fuse holder is located next to the power input. Use a flathead screwdriver to open, and replace with a T2A 250V fuse.
Can I mount this fixture upside down?
Yes, it can be mounted upside down using a hanging bracket. Always secure with a safety cable.
What do I do if the fixture overheats?
The fixture has an automatic thermal cutoff. Turn it off, let it cool for 15 minutes, ensure ventilation is not blocked, and restart.
User questions about Fuze SFX WH Elation
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Lamp in PDF format for free! Find your manual Fuze SFX WH - Elation and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Fuze SFX WH by Elation.
USER MANUAL Fuze SFX WH Elation
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Elation
Model : Fuze SFX WH
Category : Lamp