LED Super Strobe ABL - Lamp Eurolite - Free user manual and instructions
Find the device manual for free LED Super Strobe ABL Eurolite in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | LED Strobe Light |
| Model | LED Super Strobe ABL |
| Brand | Eurolite |
| Light Source | High-power LEDs |
| Number of LEDs | 144 (estimated) |
| Power Consumption | 200W (max) |
| Power Supply | AC 100-240V, 50/60Hz |
| DMX Control | Yes, via 3-pin XLR |
| DMX Channels | 2 or 4 (selectable) |
| Strobe Rate | 0-20 flashes per second |
| Dimming | 0-100% linear |
| Beam Angle | 120° |
| Dimensions (L x W x H) | 12 x 10 x 5 inches (approx.) |
| Weight | 5.5 lbs (2.5 kg) |
| Housing Material | Aluminum and plastic |
| Mounting Options | Floor stand, truss clamp (bracket included) |
| Cooling | Passive heat sink |
| IP Rating | IP20 (indoor use only) |
| Control Mode | DMX, master/slave, sound-activated, standalone |
| Safety Features | Overheat protection, safety cable attachment point |
| Included Accessories | Power cord, DMX cable, mounting bracket, user manual |
| Maintenance | Clean lens with soft dry cloth; no liquid cleaners |
| Spare Parts | LED modules, power supply, control board (contact support) |
Frequently Asked Questions - LED Super Strobe ABL Eurolite
How do I connect the LED Super Strobe ABL to a DMX controller?
Use a standard 3-pin XLR DMX cable. Connect the male connector to the fixture's DMX input and the female connector to your controller or next fixture. Set the DMX address using the DIP switches or display menu. Refer to the manual for channel assignments.
Can I use this strobe light outdoors?
No, the IP20 rating means it is only suitable for indoor use in dry locations. Exposure to moisture or dust may damage the unit.
What is the maximum strobe rate?
The strobe rate can be adjusted from 0 to up to 20 flashes per second, depending on the intensity setting.
How do I clean the LED lenses?
Disconnect the power. Use a soft, lint-free cloth slightly dampened with water to gently wipe the lenses. Do not use solvents or abrasive cleaners.
The strobe light is not responding to DMX. What should I check?
Ensure the DMX cable is properly connected and not damaged. Verify that the DMX address matches the controller. Also check that the fixture is set to DMX mode. Try rebooting the controller and the fixture.
Can I mount the fixture on a truss?
Yes, use a suitable clamp (not included) attached to the included mounting bracket. Always secure the fixture with a safety cable.
How many DMX channels does the unit use?
The fixture can operate in 2-channel or 4-channel mode. In 2-channel mode, channels control dimmer and strobe speed. In 4-channel mode, additional channels provide fine control or RGB color effects if applicable.
What is the power consumption?
The maximum power consumption is approximately 200W. It requires a standard AC 100-240V, 50/60Hz power outlet.
Can I daisy-chain multiple strobes?
Yes, you can connect multiple fixtures in a DMX chain. Use the DMX through port to link to the next fixture. The total number depends on the controller's capabilities, but 32 units per line is typical.
The strobe is overheating. What should I do?
Ensure there is adequate ventilation around the fixture. Do not block the heat sink. Reduce the ambient temperature or lower the power output. If the problem persists, contact support for possible overheat protection activation.
User questions about LED Super Strobe ABL Eurolite
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Lamp in PDF format for free! Find your manual LED Super Strobe ABL - Eurolite and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. LED Super Strobe ABL by Eurolite.