Red 6 - Uncategorized FOCUSRITE - Free user manual and instructions
Find the device manual for free Red 6 FOCUSRITE in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | 6-Channel Microphone Preamp and A/D Converter |
| Brand | Focusrite |
| Model | Red 6 |
| Form Factor | 1U Rackmount |
| Dimensions (W x H x D) | 482 x 44 x 200 mm |
| Weight | Approximately 3.5 kg |
| Power Supply | Internal, 100-240 VAC, 50/60 Hz |
| Power Consumption | 30 W |
| Number of Mic/Line Inputs | 6 |
| Microphone Preamp Gain Range | 0 to 60 dB |
| Input Impedance (Mic) | 600 Ω (adjustable to 2.4 kΩ) |
| High-Pass Filter | 75 Hz, 18 dB/octave |
| Digital Outputs | ADAT, AES, S/PDIF |
| Sample Rates | 44.1 kHz to 192 kHz |
| Bit Depth | 24-bit |
| Dynamic Range | 118 dB (A-weighted) |
| THD+N | <0.0005% typical |
| Maintenance | Clean exterior with dry cloth; avoid liquids |
| Safety | Follow all warnings in manual; use grounded outlets |
| Spare Parts & Repairability | Contact Focusrite support; no user-serviceable parts inside |
| General Information | Serial number on rear panel; software drivers available at focusrite.com |
Frequently Asked Questions - Red 6 FOCUSRITE
How do I connect the Red 6 to my system?
Use the ADAT or AES outputs to connect to your audio interface. For analog connections, use balanced XLR cables for microphones.
What are the power requirements for the Red 6?
The unit requires 100–240 VAC at 50/60 Hz. It has an internal power supply. Use the included power cord.
How do I reset the Red 6 to factory defaults?
Press and hold the 48V and Pad buttons while powering on. Hold for 5 seconds until the LEDs flash.
Can I use the Red 6 with a digital console?
Yes, via the ADAT or AES output. Ensure the console supports the same sample rate and bit depth.
What sample rates are supported?
The Red 6 supports sample rates from 44.1 kHz to 192 kHz with 24-bit depth.
How do I adjust the input impedance?
Press the Impedance button on each channel to toggle between 600 Ω and 2.4 kΩ. The LED indicates the setting.
How do I enable the high-pass filter?
Press the HPF button on the desired channel. The filter is at 75 Hz with an 18 dB/octave slope.
Can I use the Red 6 with a computer without an audio interface?
No, the Red 6 is a standalone preamp and converter. It requires a digital audio interface with ADAT or AES input to connect to a computer.
How do I clean the Red 6?
Use a dry, soft cloth to wipe the exterior. Do not use liquids or solvents. Keep ventilation slots clear.
Where can I find the latest drivers?
Download drivers from the Focusrite website: focusrite.com/downloads. The Red 6 itself does not require drivers; drivers are for the compatible audio interface.
User questions about Red 6 FOCUSRITE
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual Red 6 - FOCUSRITE and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Red 6 by FOCUSRITE.
USER MANUAL Red 6 FOCUSRITE
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : FOCUSRITE
Model : Red 6
Category : Uncategorized