Stereo 200 - Receiver CYRUS - Free user manual and instructions
Find the device manual for free Stereo 200 CYRUS in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Stereo Receiver |
| Brand | Cyrus |
| Model | Stereo 200 |
| Power Output | 2 x 100W (8 ohms, 20Hz-20kHz, THD<0.05%) |
| Frequency Response | 20Hz - 20kHz ±0.5dB |
| Total Harmonic Distortion | <0.005% |
| Signal-to-Noise Ratio | >110dB (line input) |
| Inputs | 5x RCA line, 1x Phono (MM), 1x Optical, 1x Coaxial, 1x USB-A |
| Outputs | Speaker terminals, 1x Pre-out, 1x Headphone (6.3mm) |
| Bluetooth | aptX HD, AAC, SBC |
| Dimensions (W x H x D) | 430 x 100 x 360 mm |
| Weight | 12.5 kg |
| Power Consumption | 350W (max), <0.5W standby |
| Color | Black or Silver |
| Remote Control | Included (CR2032 battery) |
| Protection Features | Overload, short circuit, thermal shutdown |
| Cleaning Instructions | Wipe with a soft, dry cloth. Avoid liquids and abrasives. |
| Safety Warnings | Do not expose to moisture, ensure adequate ventilation, disconnect during storms. |
| Spare Parts & Repairability | Authorized service centers available; replacement parts through Cyrus support. |
Frequently Asked Questions - Stereo 200 CYRUS
How do I connect my speakers to the Cyrus Stereo 200?
Use banana plugs or bare wire. Connect the left speaker to the left terminals (red+ and black-) and right speaker similarly. Ensure the impedance is at least 4 ohms. Tighten the binding posts securely.
How do I set up a turntable with this receiver?
Connect your turntable's RCA cables to the Phono input. If your turntable has a built-in preamp, use a line input instead. Make sure the grounding wire is connected to the GND terminal to avoid hum.
Can I stream audio via Bluetooth?
Yes, the Stereo 200 supports Bluetooth aptX HD for high-quality streaming. Press the Bluetooth button on the remote or front panel, then pair from your device. The receiver appears as 'Cyrus Stereo 200'.
What is the power output of the Cyrus Stereo 200?
It delivers 2 x 100W into 8 ohms (20Hz-20kHz, THD<0.05%). It can drive speakers with impedance down to 4 ohms, providing up to 160W per channel.
How should I clean the receiver?
Use a soft, lint-free cloth slightly dampened with water (if needed) to wipe the exterior. Never use solvents or abrasive cleaners. Ensure the unit is unplugged and dry before reconnecting.
Does it have a headphone output?
Yes, there is a 6.3mm headphone jack on the front panel. When headphones are plugged in, the speaker outputs are muted automatically.
How do I factory reset the Cyrus Stereo 200?
Turn off the receiver. Press and hold the Standby button on the front panel for about 10 seconds while turning it back on. The display will show 'RESET' and the unit will restart with default settings.
What should I do if there is no sound from the speakers?
Check that the correct input is selected and the volume is not muted. Verify speaker connections are secure. Try a different source. If using Bluetooth, ensure the device is paired. If the issue persists, check if the protection mode is activated (flashing standby LED).
Can I connect a powered subwoofer?
Yes, use the Pre-out output (RCA) on the back panel to connect to your subwoofer's line input. This provides a variable output controlled by the volume knob.
How do I update the firmware on the Stereo 200?
Firmware updates are done via USB. Download the latest firmware from the Cyrus website to a FAT32-formatted USB drive. Insert it into the USB-A port, then press and hold the 'Menu' button for 3 seconds. Follow on-screen instructions.
User questions about Stereo 200 CYRUS
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual Stereo 200 - CYRUS and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Stereo 200 by CYRUS.
