ProLiant DL20 G10 - Server HP - Free user manual and instructions
Find the device manual for free ProLiant DL20 G10 HP in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Rack Server (1U) |
| Brand | HP |
| Model | ProLiant DL20 G10 |
| Processor | Intel Xeon E-2200 series or Pentium G5400 |
| Memory | Up to 64 GB DDR4 ECC (2 slots) |
| Storage | Supports up to 4 LFF or 8 SFF hot-plug SAS/SATA drives |
| Networking | 2x 1GbE embedded, optional 10GbE |
| Management | HPE iLO5 with dedicated management port |
| Power Supply | 1x 290W or 500W hot-plug power supply, optional redundant |
| Dimensions (H x W x D) | 4.32 x 43.46 x 34.73 cm (1U) |
| Weight | Approximately 7.5 kg (minimum configuration) |
| Cooling | 4 hot-plug fans |
| Expansion Slots | 1x PCIe 3.0 x16 (low profile) |
| Operating Temperature | 10°C to 35°C |
| Safety Features | Rack mount kit, bezel lock, TPM 2.0 support |
| Maintenance | Tool-less access to internal components, hot-swap drives |
| Spare Parts & Repairability | Supported: memory, drives, PSU, fans, system board |
| Common Use Cases | Virtualization, file/print serving, edge computing |
| Operating Systems | Windows Server, Linux, VMware ESXi |
Frequently Asked Questions - ProLiant DL20 G10 HP
How do I configure RAID on the HP ProLiant DL20 G10?
To configure RAID, access the Smart Storage Administrator (SSA) during POST by pressing F9. You can create RAID arrays using the embedded S100i controller or an optional HBA.
How to access the iLO5 management interface?
The default iLO5 network settings are DHCP. Find the IP address on the server's iLO Summary Screen during boot or use the HPE iLO Mobile App. Default login is Administrator/administrator.
Can the server be mounted in a standard 19-inch rack?
Yes, the DL20 G10 includes a rack mount kit for standard 19-inch racks. The server occupies 1U of rack space.
What is the maximum RAM capacity?
The server supports up to 64 GB DDR4 ECC memory via two DIMM slots. Use registered or unbuffered DIMMs.
How to update the BIOS/firmware?
Download the latest firmware from the HPE Support Center. Use the HPE SPP (Service Pack for ProLiant) or iLO5 to apply updates.
Does the server support hot-swap hard drives?
Yes, the ProLiant DL20 G10 supports hot-plug SFF (2.5-inch) or LFF (3.5-inch) SAS/SATA drives in the standard drive cage.
Why does the server overheat?
Check that all cooling fans are spinning and the ambient temperature is below 35°C. Ensure airflow is not blocked by cables or rack doors. The iLO5 dashboard shows temperature readings.
How to reset the administrator password?
If you lose the iLO password, you can reset it by powering off the server, removing the NVRAM battery for a few minutes, or using the password reset jumper on the system board.
What type of power supply does it use?
The DL20 G10 uses a hot-plug power supply with 290W or 500W options. It supports 100-240V AC input.
How to install a PCIe card?
Power off the server, remove the top cover, and install the card in the PCIe 3.0 x16 slot (low profile bracket required). Secure with the retention clip.
User questions about ProLiant DL20 G10 HP
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Server in PDF format for free! Find your manual ProLiant DL20 G10 - HP and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ProLiant DL20 G10 by HP.
USER MANUAL ProLiant DL20 G10 HP
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : HP
Model : ProLiant DL20 G10
Category : Server