ProLiant DL180 G10 - Server HP - Free user manual and instructions
Find the device manual for free ProLiant DL180 G10 HP in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Rack Server |
| Form Factor | 1U |
| Dimensions (H x W x D) | 4.3 cm x 43.5 cm x 71.1 cm (1.69 in x 17.11 in x 27.94 in) |
| Weight | Approximately 16.5 kg (36.4 lb) |
| Processor | Intel Xeon Scalable (1 or 2 sockets) |
| Memory | Up to 256 GB DDR4 (12 slots, 2666 MT/s) |
| Storage Bays | 12 x LFF SAS/SATA (or 8 x SFF) |
| Networking | 4 x 1GbE embedded |
| Power Supply | Dual redundant hot-plug, up to 1000 W |
| Management | HP iLO 5 with dedicated management port |
| Expansion Slots | 2 x PCIe 3.0 (low-profile) |
| Cooling | 6 x hot-plug fans with redundancy |
| Security | Secure Boot, TPM 2.0, chassis intrusion detection |
| Supported Operating Systems | Microsoft Windows Server, Red Hat Enterprise Linux, VMware ESXi |
| Remote Management | HTML5/iLO console, virtual media, remote power control |
| Rack Mounting | Sliding rails included |
| Maintenance | Tool-less access to drives, fans, and power supplies |
| Spare Parts | Hot-plug drives, fans, power supplies, memory modules |
| Regulatory Compliance | ENERGY STAR, RoHS, REACH |
Frequently Asked Questions - ProLiant DL180 G10 HP
How do I access the BIOS setup on the ProLiant DL180 G10?
Press F9 during boot to enter System Utilities (BIOS) for configuring hardware settings.
What is the default IP address for iLO 5?
The default iLO 5 IP is DHCP assigned. Alternatively, use the iLO DNS name or press F8 during POST to configure.
How do I replace a failed hard drive?
Locate the failed drive bay (LED illuminated amber), release the latch, slide out the drive, and insert a new hot-plug drive. The controller will automatically rebuild the array.
Can I install non-HP memory modules?
HP recommends using HP Genuine memory. Non-HP memory may work but might not be supported and could cause system instability.
How to reset iLO to factory defaults?
Power off the server, press and hold the iLO reset button (located on the system board) for 10 seconds, then power on.
What RAID levels are supported?
The embedded S100i controller supports RAID 0, 1. Optional HBA/RAID cards support RAID 5, 6, 10, etc.
How do I update the firmware?
Use HP SUM (Smart Update Manager) or iLO web interface to apply firmware updates. Reboot after update.
What is the maximum ambient temperature?
The server operates at 10°C to 35°C (50°F to 95°F) as per HP specifications.
Can I use ECC memory?
Yes, the ProLiant DL180 G10 requires registered ECC DDR4 memory for correct operation.
How to clear the system board CMOS?
Power off and unplug. Locate the CMOS button on the system board, press it for 5 seconds, reconnect and power on.
User questions about ProLiant DL180 G10 HP
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Server in PDF format for free! Find your manual ProLiant DL180 G10 - HP and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ProLiant DL180 G10 by HP.
USER MANUAL ProLiant DL180 G10 HP
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : HP
Model : ProLiant DL180 G10
Category : Server