ADP6085 - Wristwatch ADIDAS - Free user manual and instructions

Product Type	Wristwatch
Brand	Adidas
Model	ADP6085
Display Type	Analog
Case Diameter	44 mm
Case Material	Stainless steel
Bracelet Material	Silicone
Weight	50 g
Water Resistance	50 meters (5 ATM)
Battery Type	CR2032 lithium coin cell
Battery Life	Approximately 2 years
Functions	Time, date, alarm, chronograph (stopwatch)
Hands	Hour, minute, second hands with luminous fill
Dial	Black with white indices and date window at 3 o'clock
Crown	Pull-out crown for time and date adjustment
Glass	Mineral crystal
Clasp	Pin buckle
Maintenance	Clean with a soft, dry cloth; avoid chemicals
Safety	Keep away from strong magnetic fields; do not operate crown underwater
Spare Parts	Battery replacement available; strap replacement possible
Repairability	Battery replacement by watchmaker; other repairs may require authorized service

Frequently Asked Questions - ADP6085 ADIDAS

How do I set the time on my Adidas ADP6085 watch?

To set the time, pull the crown out to position 2 (second click). Turn the crown clockwise or counterclockwise to adjust the hands. Push the crown back to position 0 to start the watch.

How do I set the date?

Pull the crown out to position 1 (first click). Turn the crown clockwise to advance the date. For watches with a quickset date, turning the crown will change the date. Push back to position 0.

How do I use the chronograph?

Press the top pusher to start the chronograph. Press again to stop. Press the bottom pusher to reset to zero. Note: The chronograph may not be available on all models; refer to the dial for subdials.

Is my Adidas watch water resistant?

Yes, the ADP6085 has a water resistance rating of 50 meters (5 ATM). It is suitable for swimming and showering, but not for diving. Avoid pressing buttons underwater.

How do I set the alarm?

This analog model may not have an alarm function. If your watch has a digital subdisplay, consult the manual. Typically, pull the crown and press a pusher to toggle alarm settings.

How often should I replace the battery?

The battery typically lasts about 2 years. When the watch stops or runs slow, replace the CR2032 battery. Take it to a watchmaker to avoid damaging the seals.

Can I change the strap?

Yes, the strap can be replaced with any 22mm width strap. Use a spring bar tool to remove the old strap and attach a new one.

How do I clean my watch?

Use a soft, dry cloth to wipe the case and bracelet. For silicone straps, mild soap and water is safe. Avoid solvents or harsh chemicals.

What should I do if water gets inside the watch?

If moisture appears, remove the watch immediately and place it in a dry, warm area. If persistent, take it to a watchmaker for service. Ensure the crown is pushed in fully.

Where can I find a replacement manual?

You can download the manual for free from notice-facile.com. Search for 'Adidas ADP6085' and download the PDF.

USER MANUAL ADP6085 ADIDAS

1. Pull crown out to position 2.
2. Turn counter-clockwise to advance the time and continue until the day changes to the present day.
3. Set to the correct time.
4. Push crown back to position 1

DATE SETTING (3 HAND DATE)

1. Pull the crown out to position 2.
2. Turn the crown either clockwise or counter-clockwise and set the date for the previous day. The direction that moves the date varies on different watch models.

TIME SETTING

1. Pull crown out to position 2.
2. Turn counter-clockwise to advance the time and continue until the day changes to the present day.
3. Set to the correct time.
4. Push crown back to position 1

TIME SETTING 2 HAND (DISC)

1. Pull crown out to position 2.
2. Turn the crown either clockwise or counter-clockwise
3. Set to the correct time.
4. Push crown back to position 1.

DUAL TIME/ DAY/ DATE (3 EYE WITH DATE)

DAY/TIME SETTING

1. Pull crown out to position 3.
2. Turn crown clockwise to set day and time.
3. Return crown to position 1. NOTE: If the date is set between the hours of around 9:00 PM and 1:00 AM, the date may not change on the following day.

DATE SETTING

1. Pull crown out to position 2.
2. Turn crown clockwise to set date.
3. Return crown to position 1.

DUAL TIME SETTING

1. Press A to set dual time hand forward in 15 minute increments.
2. Press B to set dual time hand backward in 15 minute increments. NOTE: Dual time hand can be advanced rapidly by continuously pressing A or B.

CHRONOGRAPH STOPWATCH (3 EYE WITH DATE)

TIME AND DATE SETTING

1. Before setting the time, make sure the chronograph is stopped and set to zero [12:00] position.
2. Pull crown out to position 2.
3. Turn crown clockwise until the previous day's date is displayed.
4. Pull crown out to position 3 when the second hand is at the 12:00 position.
5. Turn crown to set time. Note: 24-hour hand moves correspondingly with the hour and minute hands. When setting the time be sure to check that the 24-hour hand is set properly.
6. Return crown to position 1. Note: When the crown is in position 2, do not press the pushers. Otherwise the chronograph hands will move.

CHRONOGRAPH

1. Press A to start/stop the chronograph.
2. Press B to reset to zero.

CHRONOGRAPH ZERO RESET

1. If either of the chronograph hands is not at the zero (12:00) position, pull crown out to position 3.
2. Press A to move hands clockwise; press B to move hands counter-clockwise.
3. Return crown to position 1.

CHRONOGRAPH 2 EYE WITH DATE (WITH OR WITHOUT DATE)

TIME AND DATE SETTING

1. Before setting the time, make sure the chronograph is stopped

and set to zero [12:00] position.

1. Pull crown out to position 2.
2. Turn crown clockwise until the previous day's date is displayed
3. Pull crown out to position 3 when the second hand is at the 12:00 position.
4. Turn crown to set time.

Note: 24-hour hand moves correspondingly with the hour and minute hands.

When setting the time be sure to check that the 24-hour hand is set properly.

1. Return crown to position 1.

Note: When the crown is in position 2, do not press the pushers. Otherwise the chronograph hands will move.

CHRONOGRAPH

1. Press B to start/stop the chronograph.
2. Press A for Split time, Press A again to restart
3. Press A to reset to zero.

CHRONOGRAPH ZERO RESET

1. If either of the chronograph hands is not at the zero (12:00) position, pull crown out to position 3.
2. Press A to move hands clockwise; press B to move hands counter-clockwise.
3. Return crown to position 1.

CALGARY (QFL769BB/QFL873AC)

NORMAL TIME DISPLAY

1. Press A for EL

1. Press C to select T1 or T2 format.
2. Press D to toggle chime on/off.

TIME/CALENDAR SETTING

1. In time mode, press and hold D for 2 seconds to enter time setting; hour will begin flashing.
2. Press C to increase selling value. Press D to decrease selling value.
3. Press B to enter next setting field.
4. Setting sequence is hour, minute, second, year, month, date, 12/24 Hr.
5. Press A to exit setting mode.

CHRONOGRAPH MODE

1. Press B to enter chrono mode.
2. Press D to select split or lap mode. Split mode will display the full time of all records after

each split. Lap mode will display only the new lap time after each record has been recorded.

1. Press C to start chronograph.
2. Press C again to split time.
3. Repeat step 4 until desired number of laps have been reached (maximum 10).
4. Press D to stop chrono.
5. To review, press B to enter recall mode before resetting.
6. Press D again to reset chrono.

RECALL MODE

1. Press C to recall each lap (10 maximum).
2. Press D to return to chrono.

ALARM MODE

1. Press B to enter alarm mode.
2. Press C to toggle alarm on/off.
3. Press D to select T1 Alarm 1 or T2 Alarm 2.

ALARM SETTING

1. Press and hold D for 2 seconds to enter alarm setting; hour will begin flashing.
2. Press C to increase setting value. Press D to decrease setting value.
3. Press B to set minutes.
4. Press A to exit setting mode.

NOTE: Alarm turns on automatically when exiting setting mode.

TIMER MODE

1. Press C to start countdown timer.
2. Press D to stop countdown timer. Press D again to reset timer.

TIMER SETTING

1. Press B to enter timer mode.
2. Press and hold D to enter setting mode; hour will begin flashing.
3. Press C to increase setting value. Press D to decrease setting value.
4. Press B to enter next setting field.
5. Setting sequence is hour, minute, second.
6. Press A to exit setting mode.

PEACHTREE (FL145GB)

NORMAL TIME DISPLAY

1. Press A for EL in any mode
2. Press C to toggle between Time 1 and Time 2
3. Press and hold C to set Time 1 or Time 2 as the default timer.
4. Press D to toggle chime on/off.

TIME/CALENDAR SETTING

1. In normal time display, press and hold A to enter setting mode; chime will begin flashing.
2. Press C to increase setting value. Press D to decrease setting value.
3. Press B to set and advance to next setting value.
4. Setting sequence is chime, 12/24-hour time, hour, minute, second, year, month, date, Auto EL.
5. Press A to save data and exit setting mode.

CHRONOGRAPH MODE

1. Press B to change to chronograph mode.
2. Press C to start chronograph; press D for lap when the chronograph is running.
3. Press D to change views while chronograph is running.
4. Press C to stop chronograph.

NOTE: When running, there is a maximum of 10 laps, afterward last lap will be overwritten each time

additional lap is recorded.

RECALL MODE

1. Press A to recall the memory when the chronograph is stopped.
2. Press A to view the next lap.
3. Press C or D to exit Recall Mode and go back to chronograph mode.

TIMER MODE

1. Press B to change to timer mode.
2. Press C to start timer.
3. Press C to stop timer. Press D to reset the timer when it is stopped.

TIMER SETTING

1. In timer mode, press and hold A to enter setting mode; timer type will begin flashing.
2. Press C and D to select count down stop, count down repeat, or count up timer.
3. Press B to advance to next setting field.
4. Press C to decrease and D to increase.
5. Press B to set and advance to next setting value.
6. Setting sequence is timer type, hour, minute, second.
7. Press A to save data and exit setting mode.

NOTE: Alarm will sound at 2 beeps per second, and will beep for 30 seconds after timer reaches zero.

ALARM MODE

1. Press B to change to alarm mode.
2. Press C to toggle between alarms 1, 2, 3, 4.
3. Press D to enable the alarm; press D again to disable the alarm.
4. Press B to exit alarm mode.

ALARM SETTING

1. In alarm mode, press and hold A to enter setting mode, hour will begin flashing.
2. Press C to increase; press D to decrease.
3. Press B to set and advance to next setting value
4. Setting sequence is hour, minute.
5. Press A to exit setting mode

DENVER/ CANDY / SYDNEY (UPCR-780A-P07 / QUPCR-823A-P03 / QUPCR-780A-3-P16)

NORMAL TIME DISPLAY

1. Press A for EL.
2. Press C to select T1 or T2 format.

TIME/CALENDAR SETTING

1. In time mode, press and hold D for 2 seconds to enter time setting; hour will begin flashing.

Press C to increase setting value.

1. Press C to increase setting value.
2. Press B to enter next setting field.
3. Setting sequence is hour, minute, day, year, month, date.
4. Press D to exit setting mode.

ALARM MODE

1. Press B to enter alarm mode.
2. Press C to toggle alarm/chime on/off.
3. Press D to select Home Alarm or T2 Alarm.

ALARM SETTING

1. Press and hold D for 2 seconds to enter alarm setting; hour will begin flashing.
2. Press C to increase selling value
3. Press B to set minutes.
4. Press D to exit setting mode.

NOTE: Alarm turns on automatically when exiting setting mode.

CHRONOGRAPH MODE

1. Press B to enter chrono mode.
2. Press D to select split or lap mode. Split mode will display the full time of all records after each split.

Lap mode will display only the new lap time after each record has been recorded.

1. Press C to start chrono.
2. Press C again to split time.
3. Repeat step 4 until desired number of laps have been reached (maximum 10).
4. Press D to stop chrono.
5. To review, press B to enter recall mode before reselling
6. Press D again to reset chrono.

RECALL MODE

1. Press C to recall each lap [10 maximum].
2. Press D to return to chrono.

TIMER MODE

1. Press C to start countdown timer
2. Press D to stop countdown timer. Press D again to reset timer

TIMER SETTING

1. Press B to enter timer mode.
2. Press and hold D to enter setting mode; hour will begin flashing
3. Press C to increase setting value.
4. Press B to enter next setting field.
5. Setting sequence is hour, minute, second
6. Press D to exit setting mode

Seoul / Curitiba (QFL657)

NORMAL TIME DISPLAY

1. Press A to change mode. Mode sequence is normal time,

chronograph, timer, alarm.

1. Press B for EL
2. Press C to flash time zone 2. Press and hold C 2 seconds

to toggle normal time display/time zone 2.

1. Press D to toggle key tone on/off.

NOTE: At any point in any setting mode, press B to exit setting mode.

NOTE: In any setting mode, if no pusher is operated for 30 seconds.

all changes will be saved and the setting will automatically return

to normal time display.

TIME/CALENDAR SETTING

1. In normal time display, press and hold B 2 seconds; auto EL

on/off will begin flashing.

1. Press C toggle auto EL on/off.
2. Press A to set and advance to the next setting value.
3. Press C to increase the digit; press D to decrease the digit. Press and hold C or D for fast increment/decrement.
4. Repeat steps 3 and 4 through the setting sequence. The setting sequence is: auto EL, chime on/off,

12/24-hour format, hour, minute, second, year, month/date or date/month format, month and date.

1. Press B to exit setting mode.

NOTE: Weekday is automatically updated upon exiting setting mode.

TIME ZONE 2 SETTING

1. To set Time Zone 2, press and hold C for 2 seconds to change to Time Zone 2.
2. Press and hold B for 2 seconds; the time difference between Time Zone 1 and Time Zone 2 will begin flashing.
3. Press C to increase value; press D to decrease value. Press and hold C or D for

fast increment/decrement.

1. Press B to exit setting mode.

CHRONOGRAPH MODE

1. Press A to change to chronograph mode.
2. Press B to recall lap data. Press B to scroll through laps.
3. Press C to start/stop the chronograph.
4. Press and hold D 2 seconds to reset to zero.

NOTE: Insert chronograph indicator here will flash in all modes if the chronograph is running.

LAP COUNTING

1. Press D while the chronograph is running for lap counting (up to 10 laps).

NOTE: After 8 seconds, the display will show the total chronograph time in the lower portion of the display; the next lap running time will show in the upper portion of the display.

1. Press C to stop the chronograph.
2. Press B when the chronograph is stopped to recall chronograph lap data.
3. Press C or D to exit recall mode and return to the chronograph.

TIMER MODE

1. Press A to change to timer mode.
2. Press C to start/stop the timer.
3. Press D to reset the timer.

NOTE: Alarm will sound for 30 seconds when countdown reaches zero. Press any pusher to silence alarm.

TIMER SETTING

1. In timer mode, press and hold B for 2 seconds to enter setting mode; timer type will begin flashing.
2. Press C to select countdown-stop ("CD-STP"), countdown-repeat ("CD-REP"), or countdown-then up timer ("CD-UP").
3. Press A to set and advance to next setting value.
4. Press C to increase digit, press D to decrease digit. Press and hold C or D for fast increment/decrement.
5. Repeat steps 3 and 4 through setting sequence. Setting sequence is: timer type, hour, minute, seconds.
6. Press B to exit setting mode.

ALARM MODE

1. Press A to change to alarm mode.
2. Press C to select alarm 1-4.
3. Press D to toggle alarm on/off.

ALARM SETTING

1. In alarm mode, press and hold B 2 seconds; hour will begin flashing.
2. Press C to increase digit; press D to decrease digit. Press and hold C or D for fast increment/decrement.
3. Press A to set and advance minute.
4. Repeat step 2
5. Press B to exit setting mode

NOTE: Alarm will sound for 30 seconds. Press any pusher to silence alarm.