22FL532 - Television FUNAI - Free user manual and instructions

Product Type	LED TV
Brand	Funai
Model	22FL532
Screen Size	22 inches (diagonal)
Display Resolution	1366 x 768 pixels (HD Ready)
Refresh Rate	60 Hz
Power Consumption (Typical)	30 W
Standby Power Consumption	< 0.5 W
Weight (with stand)	3.2 kg
Weight (without stand)	2.9 kg
Dimensions (W x H x D) with stand	510 x 370 x 150 mm
Dimensions (W x H x D) without stand	510 x 320 x 40 mm
Inputs	HDMI x2, USB x1, VGA x1, Component Video, Composite Video, RF Antenna
Outputs	Headphone jack, Audio Out (RCA)
Built-in Tuner	ATSC (for North America) or DVB-T (depending on region)
Speakers	2 x 5 W
Power Supply	AC 100-240V, 50/60 Hz
Cleaning	Wipe with a soft, dry cloth. Do not use liquid cleaners.
Safety	Ventilation slots must not be blocked. Use only supplied power cord.
Spare Parts	Remote control, power cord, stand. Contact Funai support for other parts.

Frequently Asked Questions - 22FL532 FUNAI

How do I connect external devices to this TV?

Use the HDMI ports for HD sources like gaming consoles or streaming sticks. For older devices, use the Composite or Component inputs. Connect your computer via VGA.

What is the supported video resolution?

The TV supports up to 1366 x 768 pixels (HD Ready). It can also accept 1080p signals but will downscale to its native resolution.

How do I reset the TV to factory settings?

Go to Menu > Settings > System > Factory Reset. Confirm the action. This will erase all custom settings.

Can I mount this TV on a wall?

Yes, the TV is VESA mount compatible (100x100 mm). Use a VESA wall mount kit suitable for a 22-inch TV.

How do I clean the screen?

Turn off the TV and unplug it. Use a soft, dry microfiber cloth to gently wipe the screen. Do not use liquids, paper towels, or harsh chemicals.

Why is there no sound?

Check if the TV is muted or volume is low. Ensure external audio devices are properly connected. Try a power cycle by unplugging for 30 seconds.

How do I use the USB port?

Insert a USB drive with JPEG, MP3, or video files. Use the Media button on the remote to access the USB content.

What should I do if the remote control stops working?

First, replace the batteries. Then, check for obstructions between the remote and TV. If still not working, try re-pairing or using the buttons on the TV.

How can I improve the picture quality?

Adjust settings from Menu > Picture. Choose a preset like Standard, Movie, or Dynamic. For best results, reduce backlight and sharpness.

Is this TV energy efficient?

Yes, the TV has a typical power consumption of 30 W and standby under 0.5 W. It meets Energy Star standards for efficient operation.

USER MANUAL 22FL532 FUNAI

UNIT INFORMATION ....1

Trademark Information ....1

Servicing....1

Cabinet Cleaning....1

Panel Cleaning ....1

Remote Control / TV....2

INITIAL SETUP ....4

OPERATIONS ....5

Watching a TV Programme ....5

Favourite ....5

EPG (Electronic Programme Guide) .....5

Sound Select....6

Sleep Timer 6

Subtitle Settings ......6

Teletext Settings....6

Switching the Input Mode ....6

Recording 7

Photo Playback ....8

PC Format 9

OTHER SETTINGS ....10

Channel Settings ....10

Picture Adjustment ....12

Sound Adjustment 13

Time Settings ....14

Lock Settings....15

Setup Adjustment 16

TROUBLESHOOTING GUIDE......18

SPECIFICATIONS....20

UNIT INFORMATION

Trademark Information

• Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. DVB is a registered trademark of the DVB Project.
• The "HD TV" Logo is a trademark of DIGITALEUROPE.

Servicing

Should your unit become inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Take the unit to a Service Centre for servicing.

Cabinet Cleaning

Gently wipe the front panel and other exterior surfaces of the unit with a soft cloth. Never use a solvent or alcohol. Do not spray insecticide liquid near the unit. Such chemicals may cause damage and discoloration to the exposed surfaces.

Panel Cleaning

If the LCD panel should require cleaning, wipe it with a cotton or soft cloth. Before cleaning the panel, disconnect the power cord.

Remote Control / TV

1. (Power)

Turns the unit on and go into the standby mode.

2. SLEEP (p. 6)

3. Number buttons

Selects the desired channel in TV mode and enters the password in the PIN code input field.

4. EXIT (p. 5)

Returns to the previous display.

1. ▲ / ▼ / ◀ / ▶ (Cursor) (p. 5)

6. OK

7. MENU (p. 10)

8. AUDIO (p. 6)

9. + / - (p. 5)

To adjust the volume.

- VOL. ◀ / ▶ (Front panel) works the same function as ◀ / ▶ (cursor) on the menu.

10. (Mute) (p. 5)

11. RED / GREEN / YELLOW / BLUE

Uses for "EPG (Electronic Programme Guide)" (p. 5) / "[Programme Edit]" (p. 11).

12. DISPLAY

Display the channel number or input source.

13. SOURCE (p. 26)

- SOURCE (Front panel) works the same function as OK to determine the setting menu.

14. PICTURE MODE (p. 12)

15. SOUND MODE (p. 13)

16. FAV / FAV (p. 5)

17. FAV (p. 5)

18. EPG

"EPG (Electronic Programme Guide)" (p. 5)

19. (p 5) / √

To select a channel.

- PROG. ▲ / ▼ (Front panel) works the same function as ▲ / ▼ (cursor) on the menu.

20. (Play / Pause) / (Skip Backward) /

▶▶ (Skip forward) / ■ (Stop) / ◀◀ (Rewind) / ▶▶ (Fast-forward)

21. REC (Record)

22. (Subtitle) (p. 6)

1. (Expand) / (Subpage) / (Hold) / (Text) / (Reveal) / (Index) (p. 6)

1. CI slot
2. USB terminal (p. 7, 8)
3. Data input from USB flash memory only.
4. User should not connect any devices to the USB terminal such as digital camera, keyboard, mouse, etc. (because these will not work.) •The software update is, in most cases, handled by an authorised service person or in some circumstances the user may be asked to do the software update themselves.
5. Coaxial digital audio output jack
6. PC (VGA) input jack
7. Audio input jack for PC connection
8. (Aerial) input jack
9. Component video, Composite video and Audio (L/R) input jacks
10. AC power cord inlet
11. SCART jack
12. HDMI (HDMI 1 / HDMI 2) input jack
13. Headphone audio output jack
14. Standby / Power indicator

Lights up red when the unit goes into standby mode.

Light off when power is on.

1. Infrared sensor window

Receives the infrared rays transmitted from the remote control.

INITIAL SETUP

This section will guide you through the unit's initial setup which includes selecting a language for your on-screen menu and auto scan, which automatically scans and memorises viewable channels.

1 After making all the necessary connections, turn on the unit using the main power switch, then press ⏻.

2 Use ◀ / ▶ to select the location, then press OK.

• Select [Home Mode], this unit is set to maximise the energy efficiency for home setting and it can be adjusted through a choice of picture and sound quality according to your preference.
• Select [Retail Mode], this unit will be set up with predefined setting for retail displays.
• If you select [Retail Mode], the confirm message will appear.

3 Use ▲ / ▼ to select [OSD Language], then select the language you want, using ◀ / ▶. 4 Use ▲ / ▼ to select [Auto Tuning], then press OK. 5 Use ▲ / ▼ to select [Country], then select the country you want, using ◀ / ▶. 6 Use ▲ / ▼ to select [Tune type], then select [DTV], [ATV] or both channel, using ◀ / ▶. 7 Press OK to start scanning.

- Scan confirmation menu will appear.

- If you press MENU during channel scanning, this operation will be paused, then press MENU again to exit the initial setup.

OPERATIONS

Read this first

These operations are accessible by remote control. Some may also be accessible by controls on the main unit.

Watching a TV Programme

To select a channel

Use repeatedly to select your desired channel, or use the Number buttons to enter a channel number, then press OK for quicker access. (e.g.) If you want to select the channel 24 without pressing OK, press 2 first, then press 4 within 3 seconds.

To adjust the volume

Use / to adjust the audio volume.

Press to turn on or off the sound right away.

- You can recover the original volume by pressing again or L + -

Favourite

You can easily find a favourite channel.

- You can set favourite channel at “[Programme Edit]” (p. 11).

1 Press FAV while watching a programme to show the favourite channel list. 2 Use ▲ / ▼ to select the channel you want, then press OK.

• Use FAV + / — to select the favorite channel while watching a program.
• Use ◀ / ▶ to move to the previous or next page.

3 Press EXIT to exit.

EPG (Electronic Programme Guide)

For Digital TV operation

You can easily find a channel or see the detailed channel information. EPG gives you scheduled information of the TV program.

1 Press EPG and use ▲ / ▼ to select a channel.

[Record] (RED) :Press to call up record list. You can choose the time of the appointment to record you want.

[Display] (GREEN) :Press to display the detail information about the programme.

[Schedule] (YELLOW) :Press to see the setting you have done before.

[Remind] (BLUE) :Press to set the time you want to remind the programme you want to see.

- When the time appointment is in conflict, it will produce a warning message.

2 Press EPG to exit.

Sound Select

For Digital TV operation

Press AUDIO to display the currently selected audio language with the number of available ones and press repeatedly to cycle through them.

DD:

Dolby Digital sound

D+ :

Dolby Digital Plus sound

AAC:

HE-AAC sound

no icon:

MPEG sound

For Analogue TV operation

Press AUDIO to display the currently selected audio mode and press repeatedly to cycle through the available audio modes.

(e.g.)

NICAM STEREO Mono

NICAM DUAL I NICAM DUAL II Mono

NICAM MONO Mono

Stereo ↔

Mono

DUAL I ← DUAL II

Mono

Sleep Timer

The sleep timer can be set to put the unit into standby mode after a set period of time.

1 Press SLEEP repeatedly to change the sleep time period.

• Each time you press SLEEP, the timer increases from 10 minutes up to 240 minutes. - Press SLEEP repeatedly until [Off] appears to cancel the sleep timer. - If the unit goes into standby mode, the sleep timer will be cancelled.

Subtitle Settings

You can change the subtitle settings used for TV programmes.

1 Press 📄 (Subtitle) repeatedly to change the subtitle language.

Teletext Settings

You can change the teletext settings used for TV programmes.

1 Press ☐ (Text) to turn on the teletext decoder.

2 Press ☐ (Text) repeatedly to show the teletext in transparent mode.

• To enlarge fonts, press.

- To select the teletext subpages, press.

• To directly select the page numbers shown at the bottom of the TV screen, use RED / GREEN / YELLOW / BLUE.

• To call up the hidden information, press.

• To hold the current page, press.

• To go back to the start page, press.

3 Press EXIT to turn off the teletext decoder.

Switching the Input Mode

You can switch the input mode to TV mode or external input mode.

1 Press SOURCE.

2 Use ▲ / ▼ to select the input mode you want, then press OK.

- [Component] will be displayed if you connected component video cables to this unit.

Recording

This unit can record a TV programme. Use a USB flash memory for saving the data.

Before you begin

You must connect the USB flash memory to USB terminal of this unit (shown below) and select [DTV] at [Input Source]. Refer to "Switching the Input Mode" (p. 6).

•The USB flash memory is not supplied with this unit. - The unit recognise a USB flash memory only. Do not use a USB hub and an extension cord between the USB flash memory and the unit. Always connect the USB flash memory to this unit directly. • We do not guarantee the all USB flash memory can be supported on this unit.

1 Press SOURCE → to display the input mode and use ▲ / ▼ to select [DTV], then press OK.

Record

2 Select the channel you want, then press REC to start recording the current programme.

3 Press to stop the recording.

• When you stop the recording, it will return to normal broadcast television.
• When the storage space of the disk is low, a warning message will appear. Then it stops recording automatically and returns to normal broadcast television.

Playback

2 Press ① (index) to call up the recorded list. 3 Use ▲ / ▼ to select the desired file, then press OK to start the playback.

Operation in Playback

Press OK to display the menu.

▶||:

Press to play or pause the playback.

◀/▶

Press to rewind or fast-forward the playback.

Each press of ◀ or ▶ will rewind or fast-forward faster, up to five times.

◀◀/ ▶▶

Press to skip backward or forward in the file.

Press to stop the playback.

EXIT:

Press to make the menu disappear while it is displayed.

Press SOURCE → and select the input mode you want to exit this mode.

Photo Playback

This unit can play JPEG picture files. Use a USB flash memory containing the files.

Before you begin

You must connect the USB flash memory to the USB terminal of this unit (shown below) and select [DTV] at [Input Source]. Refer to "Switching the Input Mode" (p. 6).

• The USB flash memory is not supplied with this unit. • The unit recognizes only a USB flash memory.

Do not use a USB hub or an extension cord between the USB flash memory and the unit.

Always connect the USB flash memory to this unit directly.

- We do not guarantee that all USB flash memories can be supported on this unit.

1 Press SOURCE → to display the input mode and use ▲ / ▼ to select [Media], then press OK. 2 Press OK to enter [PHOTO], and select [C], then press OK to enter.

3 Use ▲ / ▼ / ◀ / ▶ to select the desired file, then press OK.

4 Press OK to display the menu during the slideshow.

• Use ◀ / ▶ to select [Zoom In] or [Zoom Out] and press OK. The zoom factor: 1x, 2x and 4x
• Use ◀ / ▶ to select [Playlist] and press OK to display the list.
• Use ◀ / ▶ to select [Info.] and press OK to display the information.
• Use ◀ / ▶ to select [Move View] and press OK to move the picture, if the picture is big enough to surpass the screen.

Operation in Slideshow

▶|| :

Press to play or pause the slideshow.

/

Press to skip backward or forward the file.

■ :

Press to stop the slideshow.

[Repeat] (YELLOW) :

Press to select the repeat mode; [Repeat None], [Repeat 1] or [Repeat All] in order.

[Rotate] (▶):

Every press on ▶ will turn the picture clockwise by 90 degrees.

EXIT:

Press to go back to the previous screen.

5 Press SOURCE → and select input mode you want to exit this mode.

• Funai cannot be held responsible if your USB flash memory is not supported, nor will Funai accept any liability for damage or loss of stored data.
• A USB flash memory that required its own driver or the device with a special system such as fingerprint recognition are not supported.
• Be sure to keep a backup copy of the original files on your device before you play them back on this unit. We have no responsibilities for damage or loss of your stored data.
• To avoid damaging the USB flash memory and the unit always turn off the unit before you remove the USB flash memory.
• This unit is not allowed to use the USB flash memory which requires external power supply (500 mA or more).
• This unit can be recognised up to 60,000 files in the USB flash memory.
• This unit may not be recognised if the length of the file names is too long. Only English characters can be recognised.
• This unit does not support MTP(Media Transfer Protocol) or the file other than FAT, FAT32 and NTFS file system. If the file is not supported, error message appears.
• When the unit does not recognise the USB flash memory, try reconnecting it.
• This unit cannot play back a file which go over the limit of file restriction.

It is supported that files to be played back in this unit are recorded under the following specifications:

JPEG :
Baseline 8,192 x 8,192
Progressive 1,024 x 768

The following signals can be displayed.

Format Resolution	on Refresh rate
VGA	720 x 400 70Hz
	640 x 480	60Hz
		72Hz
		75Hz
SVGA	800 x 600	60Hz
		72Hz
		75Hz
XGA	1,024 x 768	60Hz
		70Hz
		75Hz
SXGA	1,280 x 768 60Hz
WXGA	1,360 x 768 60Hz

- Other formats or non-standard signals will not be displayed correctly.

- Please use the VGA cable that has a ferrite core.

OTHER SETTINGS

Read this first

Before adjusting each setting, press MENU to display the menu.

To exit the menu, press MENU.

Some settings need to enter PIN code, refer to "Lock Settings" (p. 15).

Channel Settings

You can edit the channel settings.

1 Use ◀ / ▶ to select [CHANNEL].

[Auto Tuning]

You can scan the DTV, ATV or both channel in your area automatically.

2 Use ▲ / ▼ to select [Auto Tuning], then press OK. 3 Use the Number buttons to enter the 4-digit PIN code you set. 4 Use ▲ / ▼ to select [Country], then select the country you want, using ◀ / ▶. 5 Use ▲ / ▼ to select [Tune type], then select [DTV], [ATV] or both channel, using ◀ / ▶. 6 Press OK to start scanning.

- When the scanning is completed, the lowest memorised digital or analogue channel will be displayed.

- If you press MENU during the scanning, this operation will be stopped and the lowest memorised channel will be displayed.

[ATV Manual Tuning]

For Analogue TV operation

You can search ATV channel manually in your area.

2 Use ▲ / ▼ to select [ATV Manual Tuning], then press OK. 3 Use the Number buttons to enter the 4-digit PIN code you set. 4 Use ▲ / ▼ to select [Current CH], then use ◀ / ▶ to select the channel you want. 5 Use ▲ / ▼ to select [Sound System], then use ◀ / ▶ to select the system you want. 6 Use ▲ / ▼ to select [Fine-Tune], then use ◀ / ▶ to adjust the setting. 7 Use ▲ / ▼ to select [AFC], then use ◀ / ▶ to select [On] or [Off].

- If you set to [On], this unit adjust tuning to near channel automatically.

8 Use ▲ / ▼ to select [Search], then press OK to start scanning.

[DTV Manual Tuning]

For Digital TV operation

You can search DTV channel manually in your area.

2 Use ▲ / ▼ to select [DTV Manual Tuning], then press OK. 3 Use the Number buttons to enter the 4-digit PIN code you set. 4 Use ◀/▶ to select the channel you want, then press OK to start scanning.

For Digital TV operation

You can edit the programme settings.

- You can check favourite channel list at "Favourite" (p. 5).

2 Use ▲ / ▼ to select [Programme Edit], then press OK to enter the programme edit list.

[Delete] (RED) :Press to delete the current channel.

[Move] (YELLOW) :Press and use ▲ / ▼ to move the current channel.

[Skip] (BLUE) :Press to skip the current channel.

[Fav] (FAV) :Press to set a favourite channel.

[Signal Information]

For Digital TV operation

You can see the detailed information about the signal.

2 Use ▲ / ▼ to select [Signal Information], then press OK.

[CI Information]

For Digital TV operation

You can see the detailed information about the Common Interface, if you have inserted the CI card.

2 Use ▲ / ▼ to select [CI Information], then press OK.

- We do not guarantee that all cards can be supported on this unit.

Picture Adjustment

You can adjust the picture settings according to your personal preference.

These settings are automatically stored after exiting the picture menu.

1 Use ◀ / ▶ to select [PICTURE].

[Picture Mode]

2 Use ▲ / ▼ to select [Picture Mode], then press OK. 3 Use ▲ / ▼ to select [Dynamic], [Standard], [Mild], or [Personal], then press OK.

• You can change picture mode easily using PICTURE MODE.
• Press PICTURE MODE repeatedly to select the picture mode you want. In this function, you can also assign the picture mode individually to each input mode.

[Contrast] / [Brightness] / [Colour] / [Tint] / [Sharpness]

2 Use ▲ / ▼ to select the item you want, then press OK, and then the setting display appears. Adjust the setting using ◀ / ▶. - You can adjust the settings if you set [Personal] in [Picture Mode].

[Colour Temp]

You can change the colour tone of the picture.

2 Use ▲ / ▼ to select [Colour Temp], then press OK. 3 Use ▲ / ▼ to select [Cold], [Normal] or [Warm], then press OK.

[Noise Reduction]

You can adjust to reduce the appearance of digitising error caused by the compression.

2 Use ▲ / ▼ to select [Noise Reduction], then press OK. 3 Use ▲ / ▼ to select [Off], [Low], [Middle], [High] or [Default], then press OK.

[Backlight]

You can adjust backlight brightness. 2 Use ▲ / ▼ to select [Backlight], then press OK, and then the setting display appears. Adjust the setting using ◀ / ▶.

Sound Adjustment

You can adjust the sound settings according to your personal preferences.

1 Use ◀ / ▶ to select [SOUND].

[Sound Mode]

2 Use ▲ / ▼ to select [Sound Mode], then press OK. 3 Use ▲ / ▼ to select [Standard], [Music], [Movie], [Sports], or [Personal], then press OK.

• You can change sound mode easily using SOUND MODE.
• Press SOUND MODE repeatedly to select the sound mode you want.

[Treble] / [Bass] / [Balance]

You can set left / right speaker settings.

2 Use ▲ / ▼ to select the item you want, then press OK. The setting display appears; adjust the setting using ◀ / ▶.

- You can adjust [Treble] and [Bass] settings if you set [Personal] in [Sound Mode].

[SPDIF Mode]

2 Use ▲ / ▼ to select [SPDIF Mode], then select [PCM], [Auto], or [Off] using ◀ / ▶.

[PCM] : PCM

[Auto] : Dolby Digital (if available)

[AD Switch]

For Digital TV operation

You can adjust audio output setting and volume for visually impaired.

2 Use ▲ / ▼ to select [AD Switch], then select [Off] or [On], using ◀ / ▶.

- Only MPEG sound is available for this function.

Time Settings

You can change Time setting.

- [Clock] will change with the area which you have selected in the Time Zone.

1 Use ◀ / ▶ to select [TIME].

[Time Zone]

You can set the time zone according to the resident area.

2 Use ▲ / ▼ to select [Time Zone], then press OK.

3 Use ▲ / ▼ / ◀ / ▶ to select the time you want, then press OK.

- Although you select [Auto], the correct time may not be displayed on the "Sleep Timer" (p. 6) depending on DTV broadcasting.

[Sleep Timer]

The sleep timer can be set the unit to go to the standby mode after an incremental period of time.

2 Use ▲ / ▼ to select [Sleep Timer], then press OK.

3 Use ▲ / ▼ to select the time you want, then press OK.

- You can also set buttons on the Remote Control; refer to "Sleep Timer" (p. 6).

[Auto Standby]

You can set the time to go into standby mode automatically when no activity is detected after power is turned on. In spite of this setting, the unit goes into standby mode automatically if there is no signal input from the antenna terminal and no user operation for 15 minutes.

2 Use ▲ / ▼ to select [Auto Standby], then press OK.

3 Use ▲ / ▼ to select the time you want, then press OK.

[OSD Timer]

You can set the OSD displaying time during no activity is detected after pressing MENU.

2 Use ▲ / ▼ to select [OSD Timer], then press OK.

3 Use ▲ / ▼ to select the time you want, then press OK.

Lock Settings

You can change Lock settings.

1 Use ◀ / ▶ to select [LOCK].

[Lock System]

You can proceed with Parental settings if you enter your PIN code.

2 Use ▲ / ▼ to select [Lock System], then press OK. 3 Use the Number buttons to enter the 4-digit PIN code you set.

• If you have not set up your PIN code as France, enter 0001.
• If you have not set up your PIN code as other country, enter 0000.
• When you enter correct PIN code, you can change following settings. • After you move to other settings, you have to enter your PIN code again to proceed Parental setting.

[Set Password]

You can set your own PIN code.

2 Use ▲ / ▼ to select [Set Password], then press OK. 3 Use the Number buttons to enter the new 4-digit number. 4 Use the Number buttons to enter the same 4-digit number again.

[Block Program]

2 Use ▲ / ▼ to select [Block Program], then press OK. 3 Press GREEN to lock the current channel.

•To unlock programme, input the PIN code you set.

[Parental Guidance]

You can set the parental rating to avoid watching an inappropriate programme for your children.

2 Use ▲ / ▼ to select [Parental Guidance], then press OK. 3 Use ▲ / ▼ to select the age restriction, then press OK.

[Key Lock]

If you set to [On], you cannot use the buttons on the unit. 2 Use ▲ / ▼ to select [Key Lock], then select [On] or [Off], using ◀ / ▶.

Setup Adjustment

You can change other settings.

1 Use ◀ / ▶ to select [SETUP].

[OSD Language]

You can select the preferred on-screen language.

2 Use ▲ / ▼ to select [OSD Language], then press OK.

3 Use ▲ / ▼ / ◀ / ▶ to select the language you want, then press OK.

[TT Language]

You can select the preferred teletext language.

2 Use ▲ / ▼ to select [TT Language], then press OK.

3 Use ▲ / ▼ / ◀ / ▶ to select the language you want, then press OK.

- You can also set buttons on the Remote Control; refer to "Teletext Settings" (p. 6).

[Hearing Impaired]

You can set Hearing Impaired mode.

2 Use ▲ / ▼ to select [Hearing Impaired], then select [On] or [Off] using ◀ / ▶.

[Hearing Impaired]:

Provides audio service for hearing impaired.

[PVR File System]

You can check the USB speed.

2 Use ▲ / ▼ to select [PVR File System], then press OK.

[Aspect Ratio]

You can change TV Screen Display mode.

2 Use ▲ / ▼ to select [Aspect Ratio], then press OK.

3 Use ▲ / ▼ to select the display mode you want, then press OK.

Available options are below.

[ATV], [DTV], [AV], [SCART]: [Auto], [4:3], [16:9], [Zoom1], [Zoom2]

[PC]: [4:3], [16:9]

[Component]: [4:3], [16:9], [Zoom1], [Zoom2]

[HDMI]: [4:3], [16:9], [Zoom1], [Zoom2], [Just Scan]

[First Time Installation]

This section will guide you through the unit's initial setup, which includes selecting a language for your on-screen menu and auto scan, which automatically scans and memorizes viewable channels.

2 Use ▲ / ▼ to select [First Time Installation], then press OK.

3 Use ◀ / ▶ to select the location, then press OK.

• Select [Home Mode]. This unit is set to maximize energy efficiency for home settings, and it can be adjusted through a choice of picture and sound quality according to your preference.
• Select [Retail Mode]. This unit will be set up with predefined settings for retail displays.
• If you select [Retail Mode], a confirmation message will appear.

4 Use ▲ / ▼ to select [OSD Language], then select the language you want using ◀ / ▶. 5 Use ▲ / ▼ to select [Auto Tuning], then press OK. 6 Use ▲ / ▼ to select [Country], then select the country you want using ◀ / ▶. 7 Use ▲ / ▼ to select [Tune Type], then select [DTV], [ATV], or both channels using ◀ / ▶. 8 Press OK to start scanning.

- A scan confirmation menu will appear.

- If you press MENU during channel scanning, this operation will be paused. Press MENU again to exit the initial setup.

[Reset]

You can restore all settings except channel settings and parental lock settings.

2 Use ▲ / ▼ to select [Reset], then press OK. 3 Press ◀ to select [Yes] to reset to default settings.

- After you select [Yes], the unit will go into standby and turn on automatically.

[CEC]

If you set to [On], the HDMI CEC function allows your device to act in conjunction with this unit.

2 Use ▲ / ▼ to select [CEC], then select [On] or [Off], using ◀ / ▶.

• Your device must be compatible with HDMI CEC in order to use this function.
• We do not guarantee that all devices can be supported on this unit.

[Software Update(USB)]

It is available to update software using USB.

2 Use ▲ / ▼ to select [Software Update(USB)], then press OK.

TROUBLESHOOTING GUIDE

Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked possibilities.

Before arranging for service, check these items. It could save you time and money.

Problem Possible Remedy
Remote control does not work	•Is unit plugged in?•Power at outlet?•Check batteries in remote control.
Bars on TV screen	•If outside antenna is being used, check for broken wire.•Check for local interference.
Picture distorted	•Try a new channel, if OK, then possibly due to poor channel reception.•If outside antenna is being used, check for broken wire.•Surrounding temperature is too low.
Picture rolls vertically	•Try a new channel, if OK, then possibly due to poor channel reception.•If outside antenna is being used, check for broken wire.•Check for local interference.
No colour	•Try a new channel, if OK, then possibly due to poor channel reception.•Is antenna connected to terminal on the back of the unit?•If outside antenna is being used, check for broken wire.•Adjust [Colour] control.
Poor reception on some channels	•Try a new channel, if OK, then possibly due to poor channel reception.•Is antenna connected to terminal on the back of the unit?•If outside antenna is being used, check for broken wire.•Check for local interference.
Weak picture	•Try a new channel, if OK, then possibly due to poor channel reception.•Is antenna connected to terminal on the back of the unit?•If outside antenna is being used, check for broken wire.•Adjust [Contrast] and [Brightness] control.•Surrounding temperature is too low.
Lines or streaks in picture	•Try a new channel, if OK, then possibly due to poor channel reception.•If outside antenna is being used, check for broken wire.•Check for local interference.
Ghosts in picture	Try a new channel, if OK, then possibly due to poor channel reception.Is antenna connected to terminal on the back of the unit?If outside antenna is being used, check for broken wire.Check for local interference.
Picture blurred	Try a new channel, if OK, then possibly due to poor channel reception.If outside antenna is being used, check for broken wire.
Sound OK, picture poor	Try a new channel, if OK, then possibly due to poor channel reception.Is antenna connected to terminal on the back of the unit?If outside antenna is being used, check for broken wire.Check for local interference.Adjust [Contrast] and [Brightness] control.
Picture OK, sound poor	Try a new channel, if OK, then possibly due to poor channel reception.Check for local interference.
No picture or sound	Try a new channel, if OK, then possibly due to poor channel reception.Is unit plugged in?Power at outlet?Is unit's power on?Is antenna connected to terminal on the back of the unit?If outside antenna is being used, check for broken wire.Unplug the AC power cord and wait for about 1 minute, then plug the AC power cord and turn on the unit again.
Different colour marks on TV screen	Try a new channel, if OK, then possibly due to poor channel reception.
Black or luminous point on TV screen	It is quality of the LCD Panel.

SPECIFICATIONS

LCD	21.6 inches (22FL532/10, 22FL552/10)
	26 inches (26FL532/10, 26FL552/10)
	31.5 inches (32FL532/10, 32FL552/10)
Television system	DVB-T(MPEG2/MPEG4-H.264), PAL-B/G, D/K, SECAM-B/G, D/K, L (22FL532/10, 26FL532/10, 32FL532/10)
	DVB-T/C(MPEG2/MPEG4-H.264), PAL-B/G, D/K, SECAM-B/G, D/K, L (22FL552/10, 26FL552/10, 32FL552/10)
Sound output	1.5 W, 8 Ω × 2(22FL532/10, 22FL552/10)
	10 W, 8 Ω × 2 (26FL532/10, 26FL552/10)
	10 W, 8 Ω × 2 (32FL532/10, 32FL552/10)

Remote control Digital encoded infrared light system

Operating temperature 5 °C to 40 °C
Power requirements	AC 220-240 V ~ , 50 Hz (22FL532/10, 22FL552/10)
	AC 220-240 V ~ , 50 Hz (26FL532/10, 26FL552/10)
	AC 220-240 V ~ , 50 Hz (32FL532/10, 32FL552/10)
Power consumption	28 W (standby: less than 0.5 W) (22FL532/10, 22FL552/10)
	40 W (standby: less than 0.5 W) (26FL532/10, 26FL552/10)
	42 W (standby: less than 0.5 W) (32FL532/10, 32FL552/10)

Terminals

Antenna UHF/VHF 75 Ω

Audio input RCA jack x 2 (L/R)

Composite video input RCA jack ×1

Component video input RCA jack ×3 (Y/Pb/Pr)

HDMI input HDMI 19pin x 2

PC input D-Sub 15pin x 1 (RGB) / Mini jack ∅3.5 mm x 1 (Audio)

SCART SCART x 1

Headphone audio output Mini jack ∅3.5 mm x 1

Coaxial digital audio output RCA jack × 1

USB terminal

USB × 1

Common Interface CI slot × 1

Dimensions without base	H:347.0 mm / W:531.0 mm / D:51.0 mm (22FL532/10, 22FL552/10)H:403.8 mm / W:634.4 mm / D:56.5 mm (26FL532/10, 26FL552/10)H:473.5 mm / W:755.0 mm / D:56.5 mm (32FL532/10, 32FL552/10)
Dimensions with base	H:384.4 mm / W:531.0 mm / D:135.5 mm (22FL532/10, 22FL552/10)H:447.9 mm / W:634.4 mm / D:180.2 mm (26FL532/10, 26FL552/10)H:517.6 mm / W:755.0 mm / D:180.2 mm (32FL532/10, 32FL552/10)

•Protruding parts excluded.

Weightwithout base	3.62 kg (22FL532/10, 22FL552/10)
	5.21 kg (26FL532/10, 26FL552/10)
	6.88 kg (32FL532/10, 32FL552/10)
Weightwith base	3.80 kg (22FL532/10, 22FL552/10)
	5.60 kg (26FL532/10, 26FL552/10)
	7.27 kg (32FL532/10, 32FL552/10)

22FL532/10 22FL552/10