SPA942 - Phone LINKSYS - Free user manual and instructions
Find the device manual for free SPA942 LINKSYS in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | VoIP Desk Phone |
| Brand | Linksys |
| Model | SPA942 |
| Lines Supported | 2 |
| Display | Monochrome LCD, 128x64 pixels |
| Programmable Keys | 4 |
| Network Interface | 10/100 Base-T Ethernet (RJ-45) |
| Power | Power over Ethernet (PoE) or AC adapter (12V DC, 1A) |
| Dimensions (W x D x H) | 8.0 x 6.5 x 3.5 inches (203 x 165 x 89 mm) |
| Weight | 1.5 lbs (680 g) |
| Audio Codecs | G.711, G.726, G.729A, G.723.1 |
| VoIP Protocols | SIP v2 (RFC 3261) |
| Speakerphone | Full-duplex |
| Headset Jack | RJ-9 (2.5mm) |
| Installation | Plug and play with provisioning server |
| Upgrade and Recovery | Firmware upgrade via TFTP/HTTP |
| Security | SRTP, TLS, Digest authentication |
| Cleaning | Wipe with dry cloth; do not use liquid cleaners |
| Operating Temperature | 32°F to 104°F (0°C to 40°C) |
| Warranty | 1 year limited |
Frequently Asked Questions - SPA942 LINKSYS
How do I set up my Linksys SPA942 phone?
Connect the phone to your network using an Ethernet cable. If using PoE, plug the cable into the LAN port; otherwise, connect the power adapter. The phone will auto-provision if configured with a provisioning server. Otherwise, configure SIP settings via the phone's web interface.
How can I access the web interface of the SPA942?
Find the phone's IP address by pressing the Setup button (star key) and navigating to Network Status. Then enter that IP in your browser. Default login: admin/admin.
How do I use the speakerphone?
Press the Speaker button (key with a speaker icon) to activate speakerphone mode. Press again to switch back to handset.
How can I set up voicemail?
Voicemail is typically configured on your PBX. On the phone, program a speed dial for voicemail. Press Messages button (envelope icon) to access.
Can I use a headset with the SPA942?
Yes, the phone has a headset jack on the left side (RJ-9 2.5mm). You need a headset adapter that fits. Press the Headset button to enable.
How do I transfer a call?
During a call, press the Transfer (Trn) soft key. Dial the target number and press Transfer again to complete (blind transfer) or wait for answer and press Transfer (attended transfer).
How do I reset the phone to factory defaults?
Go to the web interface: Admin Login > Factory Reset. Or physically: while powering on, hold the '1' key for 10 seconds until the display shows 'Factory Reset'.
What Ethernet cables are supported?
Standard Cat5e or Cat6 cables. Use the included cable or any shielded/unshielded straight-through cable.
How do I update firmware?
Download the latest firmware from Linksys support. In the web interface, go to Admin > Firmware Upgrade, upload the file, and wait for reboot.
What do the LEDs mean?
Power LED: solid green when on. Ethernet LED: green when link is up, blinking for activity. Line LEDs: solid green for active line, blinking for incoming call.
User questions about SPA942 LINKSYS
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Phone in PDF format for free! Find your manual SPA942 - LINKSYS and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SPA942 by LINKSYS.
USER MANUAL SPA942 LINKSYS
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : LINKSYS
Model : SPA942
Category : Phone