KN-URC80B - Remote control KONIG - Free user manual and instructions

Product type	Universal remote control
Brand	Konig
Model	KN-URC80B
Dimensions (approx.)	17 x 5 x 2 cm
Weight (approx.)	100 g
Power source	2 AAA batteries (not included)
Maximum range	8 m
Main functions	Control of TV, decoder, DVD player, hi-fi system, amplifier
Compatibility	Over 500 brands
Configuration	By manual code or automatic search
Housing material	ABS plastic
Color	Black
Care and cleaning	Clean with a dry, soft cloth
Safety precautions	Do not expose to moisture, do not open
Spare parts available	Batteries, protective case (subject to availability)
Repairability	Battery replacement possible, no user-serviceable parts
Warranty	2 years (depending on retailer)
General information	User manual available in multiple languages

Frequently Asked Questions - KN-URC80B KONIG

How to set up the KN-URC80B remote for my TV?

Turn on your TV. With the remote, press and hold the SET button until the LED flashes. Enter the 4-digit code for your brand (list provided in the manual). If the LED turns off, setup is successful. Test the functions.

What to do if the remote does not work?

Check the batteries: insert two new AAA batteries with correct polarity. Make sure no obstacles block the infrared signal. If the problem persists, reset the remote by removing the batteries and pressing any button for 5 seconds.

How to find the code for my brand without the manual?

Use the automatic search function: hold SET until the LED flashes, then press POWER or VOL+ repeatedly. The remote scans codes. As soon as your device turns off, press SET to save the code.

What types of devices can the remote control?

The KN-URC80B can control TVs, decoders, DVD/Blu-ray players, hi-fi systems, amplifiers, and other infrared devices. It is compatible with over 500 brands.

How to replace the batteries of the remote?

Turn over the remote, open the battery compartment by sliding the cover. Insert two new AAA batteries following the (+) and (-) markings. Close the cover.

The remote only controls the TV, not the decoder, what to do?

You must set up the remote for each device. Use the mode selector (TV, DVD, etc.) to select the device. Repeat the setup procedure for each device with its specific code.

How to reset the remote to factory settings?

Remove the batteries, wait 30 seconds, then press any button several times to discharge capacitors. Reinsert the batteries. All previous codes will be erased.

What does the LED flashing rapidly mean?

Rapid flashing usually indicates a setup error or low battery. Replace the batteries and restart the coding procedure.

Can I use this remote for a device not listed?

Yes, thanks to the automatic search function, you can try to find a compatible code. If no code works, it is possible that your device is not infrared or uses a different frequency.

Where can I download the full manual of the KN-URC80B?

The PDF manual is available for free on the site notice-facile.com in multiple languages. Go to the product page and click the download button.

USER MANUAL KN-URC80B KONIG

Universal remote control

We congratulate you on the purchase of a König universal remote control. Your new remote control replaces the original remote control of your TV, the remote control of your satellite receiver or DVB-T / cable box (also referred to as STB in the following) as well as that of your Blu-ray or DVD player / recorder. Moreover, with your KN-URC80B you can also operate your audio equipment such as CD player (CD), cassette recorder (TAPE), radio or tuner (TUNER) or an amplifier (AMP).

Read all instructions carefully and retain the instructions for reference at a later date.

You can program your remote control using the operating instructions and the associated code and brand list, via the following methods:

a) by manual programming, by entering a four digit code from the code list, b) by automatic programming, depending on the brand, by entering the three digit code from the brand list c) by an automatic searching d) or by programming the original remote control codes.

We recommend starting by using the manual programming method (a).

Inserting and replacing the batteries

Your KN-URC80B remote control is powered by two 3-Volt lithium batteries (CR 2032). Insert the batteries in accordance with the markings on the battery compartment. Please take extra care to ensure correct polarity. Dispose of the old batteries in accordance with local regulations.

Note △:

Your KN-URC80B has an internal memory to make sure that the programming is retained after changing the batteries.

We recommend that you always use new batteries. Never combine old and new batteries because the performance of your remote control and the service life of the batteries will be negatively affected.

General information

Your KN-URC80B is fitted with a 5 second protection mechanism. When programming, you must press a button within a period of 5 seconds, otherwise the remote control reverts back to its regular operating mode.

Note ▲:

A short double flash of the signal LED confirms the input, a long flash indicates cancellation. If you enter a code number incorrectly, press any key and wait for a long flash of the signal LED. You can then continue entering according to the instructions.

Functional Description

Icon TV Function STB Function DVD Function
shift	No Function No Function No Function
	On / Off, standby On / Off, standby On / Off, standby
	Signal LED Signal LED Signal LED
AV	AV AV AV
f AV	List of favourites List of favourites
e Pg	Electronic TV programme Electronic TV programme
info	Info Info Display
	Cursor up Cursor up Cursor up
	Cursor down Cursor down Cursor down
	Cursor left Cursor left Cursor left
	Cursor right Cursor right Cursor right
ok	OK OK OK
a/d	Switching between the analogue and digital tuner		Audio
exit	Exit Exit Return
opt	Opt Opt Setup
tv	Switching to the TV mode (Television)
stb	Switching to the STB mode (SAT receiver or DVB-T / cable box)
dvd	Switching to the DVD mode (DVD / Bluray player or recorder)
aux	Switching to the AUX mode (any TV, STB, DVD or other appliance)
vol ▲	Volume+	Volume+	Volume+
	Mute	Mute	Mute
prog ▲	Programme+ Programme+	Programme+
vol ▼	Volume-	Volume-	Volume-
menu	Menu	Menu	Menu
prog ▼	Programme- Programme-	Programme-
	Switch video text on	Switch video text on	Subtitle
	Switch video text off
	16:9 Display format
●		Recording	Recording
		Reverse	Reverse to title
▶II		Play(press briefly) / Pause(press for longer time)	Play(press briefly) / Pause(press for longer time)
		Stop Stop
		Fast-forward	Skip title
○	Red	Red
○	Green	Green
○	Yellow	Yellow
○	Blue	Blue
CD Function TAPE Function TUNER Function AMP Function
On / Off, standby On / Off, standby On / Off, standby On / Off, standby
Volume+ Volume+ Volume+ Volume+
Mute Mute Mute Mute
		Programme+
Volume- Volume- Volume- Volume-
		Programme-
	Recording Switching to		VCR input
Reverse to title Fast-forward
Play(press briefy) / Pause(press for longer time)	Play(press briefy) / Pause(press for longer time)
Stop Stop
Skip title Reverse
			Switching to CD input
			Switching to TAPE input
			Switching to TAPE input
			Switching to TV input

Manual Programming

1) Switch on your TV, satellite receiver or your DVB-T / cable box (STB), your DVD / Blu-ray player or recorder (DVD) and your audio equipment. 2) Page to the brand of your equipment "TV", "STB", "DVD", "CD", "TAPE", "TUNER" or "AMP" in the list of codes. One or more 4-digit codes are displayed for each brand. 3) Press and hold the v), (stb), (dvd) or (aux) button depending on the level that you would like to programme, until the signal LED (⏻) flashes twice.

Note:

For audio equipment, first press the (Shift Symbol) button and then the TV/CD button (tv/cd) for CD, STB/TAPE button (stb/tape) for TAPE, DVD/TUNER button (dvd/tuner) for TUNER or AUX/AMP button (aux/amp) for AMP

4) Use the number keys to enter the first four-digit code from the code list for the brand that you have selected. The signal LED (💡) flashes twice to indicate that the code has been accepted. 5) Test the functionality of your remote control using the standby button() and then with the buttons 1 to 47 (according to the function description table). 6) If the equipment does not respond or only partially to the button commands, repeat the steps 3 to 5 using the next code from the list of codes. 7) If the equipment responds properly to all functions, your KN-URC80B is programmed correctly and can be used. Please make a note of the code used for reference.

My programming codes to use:

TV STB DVD	AUX CD TAPE TUNER AMP

Automatic programming according to the brand

Alternatively, or if in case of manual programming the correct code for your equipment cannot be found, you may use the automatic search for brand for programming.

1) Switch on your TV, satellite receiver or your DVB-T / cable box (STB), your DVD / Blu-ray player or recorder (DVD) and your audio equipment. 2) Page to the brand of your equipment under the relevant "TV", "STB", "DVD", "CD", "TAPE", "TUNER" or "AMP" section in the list of brands given in the Appendix of this manual. There is a 3-digit brand code for each brand. 3) Press and hold the TVt(), STB (stb), DVD (dvd) or AUX (aux) button depending on the level that you wish to programme until the signal LED (fl) flashes twice.

Note:

For audio equipment, first press the Shift button (shift) and then the TV/CD button (tv/cd) for CD, STB/TAPE button (stb/tape) for TAPE, DVD/TUNER button (dvd/tuner) for TUNER or AUX/AMP button (aux/amp) for AMP

4) Using the numeric buttons, enter the code 1 0 0 3 for TV. the code 3 0 0 3 for STB, the code 5003 for DVD, the code 6003 for CD, the code 7 0 0 3 for TAPE, the code 8 0 0 3 for TUNER or the code 9003 for AMP.

The signal LED (⏻) flashes twice in order to confirm that the search mode has been activated.

5) Use the number keys to enter the three-digit brand code from the brand list for the brand that you have selected. The signal LED (①) flashes twice to indicate that the code has been accepted.

6) For TV, STB and AMP, hold the standby button (); for DVD, CD and TAPE, hold the stop button (■) or for the TUNER, hold button 2 (2) of your KN-URC80B pressed until the equipment switches off; for DVD, CD or TAPE until playback stops or with the TUNER, until it switches to the next programme. This step may take several minutes.

7) As soon as the equipment responds, press the OK button (k) to confirm the programming and hold it until the signal LED (💡) flashes twice. 8) Test the functionality of your remote control using the standby button () and then with the buttons 1 to 47 (according to the function description table). 9) If the equipment responds properly to all functions, your KN-URC80B is correctly programmed and can be used.

Note ▲:

It could happen that during the search process, the KN-URC80B finds several codes to which your TV set responds, but where all buttons do not function for each code. In this case, the search process should be re-started (steps 3 to 9) until you obtain the best code. Re-starting the search process starts at the last saved programming.

Automatic search feature

Alternatively, or if either in case of manual programming or with automatic programming, the correct code for your equipment cannot be found, you may use the automatic search feature.

1) Switch on your TV, satellite receiver or your DVB-T / cable box (STB), your DVD / Bluray player or recorder (DVD) and your audio equipment. 2) Press and hold the TV (tv), STB (stb), DVD (dvd) or AUX (aux) button depending on the level that you wish to programme until the signal LED (fl) flashes twice.

Note:

For audio equipment, first press the Shift button (shift) and then the

TV/CD button (tv/cd) for CD,

STB/TAPE button (stb/tape) for TAPE,

DVD/TUNER button (dvd/tuner) for TUNER or

AUX/AMP button (aux/amp) for AMP

3) Using the numeric buttons, enter

the code 1 0 0 1 for TV,

the code 3001 for STB.

the code 5001 for DVD,

the code 6001 for CD.

the code 7001 for TAPE,

the code 8001 for TUNER or

the code 9001 for AMP.

The signal LED (⏻) flashes twice in order to confirm that the search mode has been activated.

4) For TV, STB and AMP, hold the standby button(); for DVD, CD and TAPE, hold the stop button (1) or for the TUNER, hold button 2 (2) of your KN-URC80B pressed until the equipment switches off; for DVD, CD or TAPE until playback stops or with the TUNER, until it switches to the next programme. This step may take several minutes. 5) As soon as the equipment responds, press the OK button(k) to confirm the programming and hold it until the signal LED (⏻) flashes twice. 6) Test the functionality of your remote control using the standby button() and then with the buttons 1 to 47 (according to the function description table). 7) If the equipment responds properly to all functions, your KN-URC80B is correctly programmed and can be used.

Note △:

It could happen, that during the search process, the KN-URC80B finds several codes to which your TV set responds, but where all buttons do not function for each code. In this case, the search process should be re-started (steps 2 to 7) until you obtain the best code. Re-starting the search process starts at the last saved programming.

Code reader

The code reader can be used to display the codes that you have found in the search process so that you can make a note of them:

1) Press and hold the TVv(), STB (stb), DVD (dvd) or AUX (aux) button depending on the level that you wish to programme until the signal LED (fl) ashes twice.

Note :

For audio equipment, first press the Shift button (shift) and then the

TV/CD button (tv/cd) for CD,

STB/TAPE button (stb/tape) for TAPE,

DVD/TUNER button (dvd/tuner) for TUNER or

AUX/AMP button (aux/amp) for AMP

2) Use the number buttons to enter the code 0 0 0 2. The Signal LED (1) flashes twice again. 3) Press 1 and count the number of times the Signal LED flashes; this is the first number. 4) Press 2 and count the number of times the Signal LED flashes; this is the second number. 5) Press 3 and count the number of times the Signal LED flashes; this is the third number. 6) Press 4 and count the number of times the Signal LED flashes; this is the fourth number.

Note:

The Signal LED does not flash if the number is 0. Steps 3 to 6 can be carried out in any order and as many times as required.

Learn feature

Alternatively, or if either in case of manual programming or with automatic programming, the correct code for your equipment cannot be found, you may use the learn feature.

The learn feature may also be used if certain button functions of the original remote control are not included in the database.

Positioning the KN-URC80B and original remote control (Range test)

In order to ensure that the remote control can receive the signal, both remote controls should be placed opposite one another with their transmission diodes facing each other. The distance between both remote controls should not be greater than 5 cm.

You may use the range test to determine the optimal position for learning the codes:

1) Press and hold the TV (tv), STB (stb), DVD (dvd) or AUX (aux) button depending on the level that you wish to programme until the signal LED (1) flashes twice.

Note:

For audio equipment, first press the Shift button (shift) and then the

TV/CD button (tv/cd) for CD,

STB/TAPE button (stb/tape) for TAPE,

DVD/TUNER button (dvd/tuner) for TUNER or

AUX/AMP button (aux/amp) for AMP

2) Enter the code 0 0 1 1 using the numeric buttons. The signal LED flashes twice again.

3) Now, the signal LED lights up in orange and displays the quality of the signals received.

Now place the original remote control and press and hold any button on it.

Change the distance to the KN-URC80B remote control until the signal LED lights up in green.

Note:

Orange light indicates readiness and that the KN-URC80B is not receiving any signal.

If the signal LED lights up in red, it means that the signal is too weak (too far away) or too strong (too near).

If the signal LED lights up in green, it indicates optimal signal quality (optimal alignment for learning).

4) To end the range test, press the TV, STB (stb), DVD (dvd) or AUX (aux) button that had been pressed earlier.

Note ▲:

The optimal alignment depends on the transmission strength of the signals by the original remote control and, hence, it may vary for each remote control. This is why you need to carry out the range test with each remote control from which you would like to learn in order to determine the optimal alignment for it.

Learning – Basic

1) Press and hold the TV(√), STB (stb), DVD (dvd) or AUX (aux) button depending on the level that you wish to programme until the signal LED (💡) flashes twice.

Note:

For audio equipment, first press the Shift button (shift) and then the

TV/CD button (tv/cd) for CD

STB/TAPE button (stb/tape) for TAPE,

DVD/TUNER button (dvd/tuner) for TUNER or

AUX/AMP button (aux/amp) for AMP

2) Enter the code 0 0 0 9 using the numeric buttons. The signal LED flashes twice again. 3) Now, the signal LED lights up in green. 4) Press the button on the KN-URC80B remote control that you would like to teach, e.g., standby (⏻) 5) The signal LED lights up in orange and indicates that the KN-URC80B remote control is ready to learn. 6) Press and hold the desired button on the original remote control until the green signal LED goes off.

Note:

Orange light indicates that the KN-URC80B is not receiving any signal.

If the signal LED lights up in red, it means that the signal is too weak (too far away) or too strong (too near).

7) You may repeat the steps 3 to 6 to teach (or programme) other buttons. To save and end the learning function, press the TV (tv), STB (stb), DVD (dvd) or AUX (aux) button that had been pressed earlier.

Note ▲:

If the buttons that have been learnt do not work properly with your equipment, or particularly if only every second button that you press works, please carry out Advanced Learning.

Learning - Advanced

1) Press and hold the TV (tv), STB (stb), DVD (dvd) or AUX (aux) button depending on the level that you wish to programme until the signal LED (fl) ashes twice.

Note:

For audio equipment, first press the Shift button (shift) and then the

TV/CD button (tv/cd) for CD,

STB/TAPE button (stb/tape) for TAPE,

DVD/TUNER button (dvd/tuner) for TUNER or

AUX/AMP button (aux/amp) for AMP

2) Enter the code 0 0 1 0 using the numeric buttons. The signal LED flashes twice again. 3) Now, the signal LED lights up in green. 4) Press the button on the KN-URC80B remote control that you would like to teach, e.g., standby (⏻) 5) The signal LED lights up in orange and indicates that the KN-URC80B remote control is ready to learn. 6) Press and hold the desired button on the original remote control until the green signal LED goes off.

Note:

Orange light indicates that the KN-URC80B is not receiving any signal.

If the signal LED lights up in red, it means that the signal is too weak (too far away) or too strong (too near).

7) Press and hold the same button on the original remote control once again until the green signal LED goes off. 8) You may repeat the steps 3 to 7 to teach (or programme) other buttons. To save and end the learning function, press the TV (tv), STB (stb), DVD (dvd) or AUX (aux) button that had been pressed earlier.

Operating the volume control on the TV or satellite receiver or the DVB-T / cable box (STB) or DVD player / recorder

By default, the volume and mute controls are operated on the satellite receiver or DVB-T / cable box or DVD player / recorder.

If you would like to operate these controls on the TV, please carry out the following steps.

1) Press and hold the TV button ( ), until the signal LED (D) flashes twice. 2) Enter the code 0 0 0 4 using the numeric buttons. The signal LED flashes twice again.

If you would like to restore the volume control functions again to the satellite receiver or the DVB-T / cable box (STB) or the DVD player / recorder, please carry out the following steps.

1) Press and hold the TV button ( ) until the signal LED (D) flashes twice. 2) Enter the code 0 0 0 5 using the numeric buttons. The signal LED flashes twice again.

Disabling buttons

You have the option of disabling individual functions or features that are not required on the KN-URC80B remote control.

1) Press and hold the TV ( ), STB (stb), DVD (dvd) or AUX (aux) button, depending on the function or feature that you would like to disable, until the signal LED (Ⓤ) flashes twice.

Note:

For audio equipment, first press the Shift button (shift) and then the

TV/CD button (tv/cd) for CD,

STB/TAPE button (stb/tape) for TAPE,

DVD/TUNER button (dvd/tuner) for TUNER or

AUX/AMP button (aux/amp) for AMP

2) Enter the code 0 0 0 6 using the numeric buttons. The signal LED flashes twice again. 3) Press all those buttons whose function or feature you would like to disable one after another. 4) Press the level button used in step 1 to save the results.

Note △:

The numeric and level buttons cannot be disabled.

Note ▲:

If you would like to enable the buttons that you have disabled, please reset the remote control completely. See function "Delete Settings (Reset)"

Code block

In order to prevent inadvertent programming of the KN-URC80B remote control you can enable the codes to be blocked.

1) Press and hold the TV button() until the signal LED (D) flashes twice. 2) Enter the code 0 0 0 7 using the numeric buttons. The signal LED flashes twice again. 3) The remote control is now blocked against reprogramming

Note ▲:

You can recognise that the code block is active (enabled) if the signal LED ⏻ of the KN-URC80B remote control flashes long once and not twice briefly when trying to programme it.

Note △:

Repeat the steps 1 to 3 if you wish to disable the code block once again.

Delete settings (Reset)

1) Press and hold the TV button() until the signal LED (D) flashes twice. 2) Using the numeric buttons, enter the code 0 0 0 0. The signal LED (⏻) flashes twice in order to confirm that the KN-URC80B remote control has been reset.

Note ▲:

When you use the "Delete Settings (Reset)" function, your KN-URC80B remote control loses all its programming and is restored to its condition at the time of delivery.

Note on environmental protection

After the implementation of the European Directive 2002/96/EU in the national legal system, the following applies:

Electrical and electronic devices may not be disposed of with domestic waste. Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilising old devices, you are making an important contribution to protecting our environment.

GUARANTEE

Your remote control is guaranteed for a period of two years from the date of purchase. Please consult the dealer in the event of a guarantee claim.

MANUEL D'UTILISATION

MANUAL DE INSTRUÇÕES

Controlo remoto universal König KN-URC80B

STB/TAPE keys (stb/ape) for TAPE,

DVD/TUNER keys (dvd/tuner) for TUNER or

AUX/AMP keys (aux/amp) for AMP

code 3 0 0 3 for STB,

code 5 0 0 3 for DVD,

code 6003 for CD,

code 7 0 0 3 for TAPE,

code 8 0 0 3 for TUNER or

code 9 0 0 3 for AMP.

code 3 0 0 1 for STB,

code 5001 for DVD,

code 6 0 0 1 for CD,

code 7 0 0 1 for TAPE,

code 8 0 0 1 for TUNER or

code 9 0 0 1 for AMP.