PDSI 5081/1 A - Dishwasher PRIVILEG - Free user manual and instructions

USER MANUAL PDSI 5081/1 A PRIVILEG

Close-up of three wooden clothespins with metal clips, no text or symbols visible

Installations- och underhållsanvisningar Instrukser for installasjon og vedlikehold Vedledning for installation ogvedligeholdelse Asennus- ja huolto-ohjeet Instruções para a instalação e a manutenção

Close-up of two glass bottles with black lids, one partially filled with white paper (no visible text or symbols)

Close-up of several empty glasses with blurred background (no text or symbols visible)

Close-up of a white industrial or laboratory device with perforated surface and mounting bracket (no visible text or symbols)

• Connection to the mains water supply must be carried out by a qualified technician in compliance with the manufacturer's instructions and applicable local safety regulations.
• All local water board regulations must be complied with. Water supply pressure: 0.03 - 1.0 MPa.
• The inlet hose must be securely clamped to the water tap to prevent leaks.
• The inlet water temperature varies according to the model installed. Inlet hose marked: "25°C Max": up to a maximum of 25°C. Other models: up to a maximum of 60°C.
• Depending on the appliance model, the solenoid valve of the inlet hose will be activated by the mains voltage (see assembly instructions).
• Make sure the inlet and drain hoses are kink-free and are not crushed.
• Fix the drain hose to the siphon with a clamp to prevent it from coming off during operation.
• When installing the appliance, make sure water can drain freely (remove the siphon plug if necessary).
• Do not use old or damaged hoses. Use only the hoses provided or new ones, which can be requested from the After-Sales Service.
• If hoses are not long enough, contact your local dealer.
• Do not cut hoses and, in the case of appliances fitted with a waterstop system, do not immerse the plastic casing containing the inlet hose in water.
• Before using the appliance for the first time, check the water inlet and drain hose for leaks.

2. Electrical Connection

• All local electricity board regulations must be complied with.
• Voltage information is shown on the rating plate mounted inside the door on the right hand side.
• The appliance must be earthed as prescribed by law.
• Do not use extension leads or multiple adapters.
• If the power cable is damaged, replace it with an identical one. The power cable must only be replaced by a qualified technician.
• After appliance installation, the mains plug must be easily accessible so that the appliance can be unplugged if necessary at any time.

For Austria:

If a fault current switch is fitted upline of the appliance, this must be pulse current-sensitive.

3. Assembly instructions

• During assembly the appliance must be unplugged from the mains.
• Set any electrical screwdrivers to a low torque.
• Leave a gap of at least 3 mm between the top edge of the wooden door and the worktop.
• Do not seal the gaps between adjacent units and the worktop (for example with silicone).
• Attention: when transporting and assembling the appliance, always wear gloves to protect fingers / hands from sharp edges and corners.
• If the appliance is installed at the end of a row of units, making the side panel accessible, the hinge area must be covered to prevent any risk of crushing (cover available from After-sales Service).
• Be careful with uneven installation surfaces: Carefully push the dishwasher with feet unscrewed under the worktop.
• After fitting the plinth and decor panel and before opening the door, evaluate whether the plinth needs to be cut and, if so, how much (see assembly instructions) in order to avoid any damage.
• The sharp edges of the unit and the plinth must be protected from humidity (with insulating material, for example silicone, not included with the appliance).

4. General indications

• The appliance must only be used in the household and according its purpose.
• Do not use the dishwasher until it has been fully assembled.
• Do not use the dishwasher if it has been damaged in transit. Contact After-Sales Service or your local dealer.
  Before carrying out any cleaning or maintenance operations, unplug the appliance and turn off the water tap. The same applies in the event of a malfunction.
• Do not use abrasive products or alcohol on the control panels.
• All sizes in this maintenance and installation manual are given in millimetres.
• Packaging varies according to the dishwasher model.

ELECTRICAL CONNECTION

I) For Great Britain only

Warning - this appliance must be earthed

Fuse replacement

If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A.S.T.A. approved fuse to BS 1362 type and proceed as follows:

I. Remove the fuse cover (A) and fuse (B).
2. Fit replacement I3A fuse into fuse cover.
3. Refit both into plug.

Important:

The fuse cover must be refitted when changing a fuse and if the fuse cover is lost the plug must not be used until a correct replacement is fitted.

Correct replacement are identified by the colour insert or the colour embossed in words on the base of the plug.

Replacement fuse covers are available from your local electrical store.

2) For the Republic of Ireland only

The information given in respect of Great Britain will frequently apply, but a third type of plug and socket is also used, the 2-pin, side earth type.

3) Socket outlet / plug (valid for both countries)

If the fitted plug is not suitable for your socket outlet, please contact Whirlpool Service for further instruction. Please do not attempt to change plug yourself. This procedure needs to be carried out by a qualified Whirlpool technician in compliance with the manufactures instructions and current standard safety regulations.

Technical diagram of a plug electrical socket with labeled components A and B, showing internal wiring and mounting points.

1. Branchements hydriques

.הכלההוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָהוּרָה

-

-

-

-

Diagram illustrating airflow or ventilation through a pipe system with labeled component 1

Technical diagram showing a cabinet with labeled components and directional arrows, including a magnified inset of a curved component.

820 - 900 mm 820 - 850 mm 850 - 900 mm 4X 1X 1X 3 + + 2X 2X

Technical diagram showing hand tooling and measuring a bolt using a ruler, with numbered steps and a magnified view of the tool's measurement.

850 - 900 mm

graph TD
    A["Start: Wire Connection"] --> B["Step 1: Switching to Panel"]
    B --> C["Step 2: Switching to Motor"]
    C --> D["Step 3: Control with Pin 3"]
    D --> E["End: Motor Control"]

MIN 10 mm p=0,3 - 10 bar (0,03 - 1,0 MPa) ~1200 mm ~1500 mm ~1600 mm min. 400mm min. 400mm MIN.10 mm 6

3 mm 8 22

Technical line drawing of a cabinet with mounting fixtures and a mechanical assembly showing rotational components (no text or symbols)

Technical diagram illustrating mechanical assembly with labeled components and directional arrows indicating motion or force vectors.

Diagram of a mechanical assembly with rotating springs and fasteners, showing motion direction (no text or symbols)

Y (mm) - X (mm) = min.87mm min 87mm X Y C 11 MEERC21 11 30 11 NED

1.2.

1,2,3,...? 4619 729 00781

graph TD
    A["1. Measurement of 5kg"] --> B["Device with max 5kg"]
    B --> C["2. Component A"]
    C --> D["Output"]

1. 

Ø 1,5 mm min. 4 mm

1. 

max. 5kg 16-22,6mm A 4x 7 4x 9 592 / 594mm

5.6.

4x 1 2 3 4 5 6 5 6 1 2 3 4 5 6

graph TD
    A["Component A"] -->|1. Flow to A| B["Component A"]
    B -->|2. Flow to B| C["Component B"]
    C -->|3. Flow to C| D["Output"]
    style A fill:#f9f,stroke:#333
    style B fill:#bbf,stroke:#333

7.8.

Pure technical diagram of a structural frame with labeled section A and directional arrows, no text or symbols present.

4x 10 max. 2mm

1. 

Diagram of a mechanical device with rotating arm and warning symbol (no text or labels)

10a./10b.

Simple geometric shapes including a vertical rectangle and a checkmark, with no text or symbols present.

10a. 10b.

605

Simple line drawing of a shopping cart and a ramp over a staircase (no text or symbols)

Line drawing of a cabinet with an open drawer and curved handle, showing directional arrows (no text or symbols)

Safety warning illustration showing a hand holding a tool with a cross mark and a warning symbol below.

D	Wartung und Reinigung
GB	Maintenance and Cleaning
F	Entretien et nettoyage
NL	Onderhoud en reiniging
E	Limpieza y conservación
P	Manutenção e limpeza
I	Manutenzione e pulizia
GR	Συντήρηση και καθαρισμός
S	Skötsel och rengöring
N	Pleie og rengjøring
DK	Vedligeholdelse og røngøring
FIN	Huolto ja puhdistus
PL	Konserwacja i czyszczenie
CZ	Üdržba a čištění
SK	Üdržba a čistenie
H	Karbantartás és tisztítás
RUS	Чистка и обслуживание
BG	Почистване и поддръжка
RO	Întreținerea și curățarea
HR	Održavanje i čišćenje
TR	Bakım ve temizlik
Arabic	الصيانة وال텐ظيف
Hebrew	###
KO	유지보수 및 청소

Technical line drawing showing a faucet and its internal structure with spray pattern (no text or symbols)

1. 

Technical diagram of a mechanical assembly with labeled component A (no text or symbols present)

Technical line drawing of a mechanical assembly with a base and component, no visible text or symbols

1. 

C D

1. 

Technical line drawing of a mechanical assembly with no visible text or symbols

Diagram showing a faucet spraying water onto a shared air vent (no text or labels)

1.

A

B

2.

Diagram illustrating a mechanical component with labeled parts and visual indicators including a faucet, sad face, and smiling face.

3.

E

Technical diagram of a mechanical assembly with no visible text or symbols

Three technical line drawings of industrial components: a faucet, a fan-shaped housing, and a cylindrical container (no text or symbols)

1. 

A

Technical line drawing of a mechanical assembly with labeled component B and directional arrow (no text or symbols beyond labels)

1. 

Technical line drawing of a mechanical component with labeled part 'C' and directional arrow (no text or symbols beyond label)

1. 

Technical line drawings of household appliances including a faucet, door, and storage unit (no text or labels)

Technical line drawings of two mechanical components: a U-shaped fan and a cylindrical housing (no text or symbols)

1. 

4. E

1. 

Technical line drawing of a mechanical assembly with two views (front and side), no visible text or symbols